SIST EN 12365-2:2003
(Main)Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 2: Linear compression force test methods
Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 2: Linear compression force test methods
This part 2 of prEN 33/WI 131/245 specifies the method to be used to select, condition and test samples of gasket or weatherstripping, to determine the force required to deflect them by a predetermined amount under the conditions layed down in the test. The test has been devised to cover all likely gasket and weatherstripping shapes or materials.
Schlösser und Baubeschläge - Dichtungen und Dichtungenprofile für Fenster, Türen und andere Abschlüsse sowie vorgehängte Fassaden - Teil 2: Linearer Schließdruck, Prüfverfahren
Dieser Teil der EN WI 33245 legt das Verfahren fest, das für die Auswahl, Konditionierung und Prüfung von Proben von Dichtungen und Dichtungsprofilen a anzuwenden ist, um die erforderliche Kraft zu bestimmen, mit der sie unter den für die Prüfung vorgeschriebenen Bedingungen um ein zuvor festgelegtes Maß zusammengedrückt werden. Die Prüfung gilt für alle möglichen Formen oder Materialien von Dichtungen und Dichtungsprofilen.
Quincaillerie pour le bâtiment - Profilés d'étanchéité de vitrage et entre ouvrant et dormant pour portes, fenetres, fermetures et façades rideaux - Partie 2: Méthodes d'essai pour déterminer la réaction linéique a la déformation
La présente partie de l'EN 12365 spécifie la méthode devant être utilisée pour sélectionner, préparer le conditionnement et soumettre aux essais des échantillons de profilés d'étanchéité de vitrage et entre ouvrant et dormant afin de déterminer la force nécessaire pour les comprimer et les déformer à leur épaisseur de travail minimale au moyen d'une valeur prédéterminée et ceci dans les conditions fixées pour l'essai.
Des exemples de détermination de la plage de travail de profilés d'étanchéité de vitrage et entre ouvrant et dormant types sont indiqués dans l'annexe A.
Stavbno okovje – Tesnila in tesnilni trakovi za vrata, okna, polkna in obešene fasade – 2. del: Preskusne metode za obremenjevanje z linijsko tlačno silo
General Information
- Status
- Published
- Publication Date
- 31-Oct-2003
- Technical Committee
- ISTP - Doors and windows
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 01-Nov-2003
- Due Date
- 01-Nov-2003
- Completion Date
- 01-Nov-2003
- Directive
- 89/106/EEC - Construction products
Relations
- Effective Date
- 22-Dec-2008
Overview
EN 12365-2:2003 - Building hardware: Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 2: Linear compression force test methods - is a CEN standard that specifies how to select, condition and test samples of gaskets and weatherstripping to determine the linear compression force required to deflect them to a defined minimum width. The method is designed to cover all typical gasket and weatherstripping shapes and materials used in building hardware.
Key topics and technical requirements
- Scope and purpose: Defines the procedure to measure force per metre required to compress or deflect sealing profiles through their working range.
- Working range classification: Nine working-range grades are identified (examples: grade 2 > 1 mm up to grade 9 > 30 mm) to characterise allowable deflection.
- Compression-force classification: Nine grades for linear compression force (examples: grade 2 > 10 N/m, grade 5 > 100 N/m, grade 9 > 1 000 N/m).
- Specimen preparation and conditioning:
- Test pieces length: 100 mm to 500 mm.
- Condition in relaxed state at 23 °C ±2 °C and 45 %–55 % RH for not less than 24 h and not more than 6 days.
- Time between forming and testing should preferably not exceed 3 months.
- Test apparatus and measurement:
- Displacement dial gauge for deflection; force gauge for load.
- Typical apparatus illustrated in Annex B (support block, anvil, moving carrier).
- Test procedure and tolerances:
- Laboratory temperature: 23 °C or 25 °C (humidity 45 % at 23 °C or 55 % at 25 °C).
- Compression speed: not exceeding 10 mm/min ± 1 mm/min.
- Record force after maintaining compression for 30 s ± 5 s.
- Measurement tolerances: compression ± 0.05 mm; force accuracy better than 1 %; length ± 0.1 mm; temperature ± 1 °C; RH ± 5 %.
- Repeat on three specimens and report the average in N/m to one decimal place.
- Test report: Must identify specimen, test house, test method, product designation, results, observations, date and signature.
Practical applications
- Quality control and product development for gaskets, seals and weatherstripping used in doors, windows, shutters and curtain walling.
- Performance specification and verification for architects, façade engineers and specifiers requiring defined compression behaviour.
- Type testing for manufacturers to classify products by working range and linear compression force.
- Independent test laboratories and certification bodies assessing compliance with EN 12365 series.
Who uses this standard
- Seal and gasket manufacturers
- Window, door and curtain-wall system suppliers
- Façade consultants and building envelope engineers
- Testing and certification laboratories
- Product specifiers and procurement teams
Related standards
- EN 12365-1:2003 - Performance requirements and classification (companion document).
- EN 12365-3 & EN 12365-4 - Other parts covering deflection recovery and recovery after accelerated ageing.
- prEN 12519:2003 - Terminology for windows and doors.
Keywords: EN 12365-2:2003, gasket test method, weatherstripping compression test, linear compression force, building hardware, doors and windows testing.
Frequently Asked Questions
SIST EN 12365-2:2003 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 2: Linear compression force test methods". This standard covers: This part 2 of prEN 33/WI 131/245 specifies the method to be used to select, condition and test samples of gasket or weatherstripping, to determine the force required to deflect them by a predetermined amount under the conditions layed down in the test. The test has been devised to cover all likely gasket and weatherstripping shapes or materials.
This part 2 of prEN 33/WI 131/245 specifies the method to be used to select, condition and test samples of gasket or weatherstripping, to determine the force required to deflect them by a predetermined amount under the conditions layed down in the test. The test has been devised to cover all likely gasket and weatherstripping shapes or materials.
SIST EN 12365-2:2003 is classified under the following ICS (International Classification for Standards) categories: 91.060.50 - Doors and windows. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 12365-2:2003 has the following relationships with other standards: It is excused to SIST EN 12365-1:2003. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 12365-2:2003 is associated with the following European legislation: EU Directives/Regulations: 305/2011, 89/106/EEC. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN 12365-2:2003 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Schlösser und Baubeschläge - Dichtungen und Dichtungenprofile für Fenster, Türen und andere Abschlüsse sowie vorgehängte Fassaden - Teil 2: Linearer Schließdruck, PrüfverfahrenQuincaillerie pour le bâtiment - Profilés d'étanchéité de vitrage et entre ouvrant et dormant pour portes, fenetres, fermetures et façades rideaux - Partie 2: Méthodes d'essai pour déterminer la réaction linéique a la déformationBuilding hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 2: Linear compression force test methods91.060.50Vrata in oknaDoors and windowsICS:Ta slovenski standard je istoveten z:EN 12365-2:2003SIST EN 12365-2:2003en,fr,de01-november-2003SIST EN 12365-2:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12365-2September 2003ICS 91.060.50; 91.190English versionBuilding hardware - Gasket and weatherstripping for doors,windows, shutters and curtain walling - Part 2: Linearcompression force test methodsQuincaillerie pour le bâtiment - Profilés d'étanchéité devitrage et entre ouvrant et dormant pour portes, fenêtres,fermetures et façades rideaux - Partie 2: Méthodes d'essaipour déterminer la réaction linéique à la déformationSchlösser und Baubeschläge - Dichtungen undDichtungenprofile für Fenster, Türen und andereAbschlüsse sowie vorgehängte Fassaden - Teil 2: LinearerSchließdruck, PrüfverfahrenThis European Standard was approved by CEN on 1 August 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12365-2:2003 ESIST EN 12365-2:2003
Examples of determining the working range of typical gaskets andweatherstripping.8Annex B (informative)
Typical test apparatus.12Annex C (informative)
Flow chart of test procedure.13SIST EN 12365-2:2003
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...