iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST ENV 1992-1-4:2004

(Main)

Eurocode 2: Design of concrete structures - Part 1-4: General rules - Lightweight aggregate concrete with closed structure

Eurocode 2: Design of concrete structures - Part 1-4: General rules - Lightweight aggregate concrete with closed structure

Migrated from Progress Sheet (TC Comment) (2000-07-10): Splitting of WI 13. Dates refer to ENV. ++ 2-Y-Review (therefore re-use of old WI and use of stage 41).

Eurocode 2: Planung von Stahlbeton- und Spannbetontragwerken - Teil 1-4: Allgemeine Regeln - Leichtbeton mit geschlossenem Gefüge

Eurocode 2: Calcul des structures en béton - Partie 1-4: Regles générales - Béton de granulats légers a structure fermée

Eurocode 2: Projektiranje betonskih konstrukcij - 1-4. del: Splošna pravila za beton iz lahkega agregata z zaprto zgradbo

General Information

Status
Withdrawn
Publication Date
31-Aug-2004
Withdrawal Date
31-Oct-2005
ICS
91.010.30 - Technical aspects
91.080.40 - Concrete structures
Technical Committee
KON - Structures
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Nov-2005
Due Date
01-Nov-2005
Completion Date
01-Nov-2005
Directive
89/106/EEC - Construction products
Mandate
M/100 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on precast concrete products
M/BC/CEN/89/11 - Framework mandate to CEN on Eurocode work : execution of a standardization programme on Eurocodes for the structural design of building and civil engineering works
Ref Project
ENV 1992-1-4:1994 - Eurocode 2: Design of concrete structures - Part 1-4: General rules - Lightweight aggregate concrete with closed structure

Relations

Replaced By
SIST EN 1992-1-1:2005 - Eurocode 2: Design of concrete structures - Part 1-1: General rules and rules for buildings
Effective Date
01-Nov-2005
Parent
SIST ENV 1992-1-3:2004 - Eurocode 2: Design of concrete structures - Part 1-3: General rules - Precast concrete elements and structures
Effective Date
22-Dec-2008

Buy Standard

ENV 1992-1-4:2004ENV 1992-1-4:2004
PreviousNext
Standardization document
ENV 1992-1-4:2004
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ENV 1992-1-4:2004
01-september-2004
Eurocode 2: Projektiranje betonskih konstrukcij - 1-4. del: Splošna pravila za beton
iz lahkega agregata z zaprto zgradbo
Eurocode 2: Design of concrete structures - Part 1-4: General rules - Lightweight
aggregate concrete with closed structure
Eurocode 2: Planung von Stahlbeton- und Spannbetontragwerken - Teil 1-4: Allgemeine
Regeln - Leichtbeton mit geschlossenem Gefüge
Eurocode 2: Calcul des structures en béton - Partie 1-4: Regles générales - Béton de
granulats légers a structure fermée
Ta slovenski standard je istoveten z: ENV 1992-1-4:1994
ICS:
91.010.30 7HKQLþQLYLGLNL Technical aspects
91.080.40 Betonske konstrukcije Concrete structures
SIST ENV 1992-1-4:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ENV 1992-1-4:2004

---------------------- Page: 2 ----------------------

SIST ENV 1992-1-4:2004

---------------------- Page: 3 ----------------------

SIST ENV 1992-1-4:2004

---------------------- Page: 4 ----------------------

SIST ENV 1992-1-4:2004

---------------------- Page: 5 ----------------------

SIST ENV 1992-1-4:2004

---------------------- Page: 6 ----------------------

SIST E
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST-TS CEN/TS 19103:2022(Main)
Eurocode 5: Design of Timber Structures - Structural design of timber-concrete composite structures - Common rules and rules for buildings
CEN/TS 19103:2021

1.1   Scope of CEN/TS 19103
(1)   CEN/TS 19103 gives general design rules for timber-concrete composite structures.
(2)   It provides requirements for materials, design parameters, connections, detailing and execution for timber-concrete composite structures. Recommendations for environmental parameters (temperature and moisture content), design methods and test methods are given in the Annexes.
(3)   It includes rules common to many types of timber-concrete composite, but does not include details for the design of glued timber-concrete composites, nor for bridges.
NOTE   For the design of glued timber-concrete composites or bridges alternative references are available.
(4)   It covers the design of timber-concrete composite structures in both quasi-constant and variable environmental conditions. For ease of use, it provides simple design rules for quasi-constant environmental conditions and more complex rules for variable environmental conditions.
1.2   Assumptions
(1)   The general assumptions of EN 1990 apply.
(2)   CEN/TS 19103 is intended to be used in conjunction with EN 1990, EN 1991 (all parts), EN  1992 (all parts), EN  1994 (all parts), EN 1995 (all parts), EN 1998 (all parts) when timber structures are built in seismic regions, and ENs for construction products relevant to timber structures.

  • Technical specification
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1992-1-2:2005/A1:2019(Amendment)
Eurocode 2: Design of concrete structures - Part 1-2: General rules - Structural fire design
EN 1992-1-2:2004/A1:2019

DOP of 12 months!

  • Amendment
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1992-4:2018(Main)
Eurocode 2 - Design of concrete structures - Part 4: Design of fastenings for use in concrete
EN 1992-4:2018

1.1   General
(1)   This EN provides a design method for fastenings (connection of structural elements and non-structural elements to structural components), which are used to transmit actions to the concrete.
Inserts embedded in precast concrete elements during production, under Factory Production Control (FPC) conditions and with the due reinforcement, intended for use only during transient situations for lifting and handling, are covered by the CEN/TR “Design and Use of Inserts for Lifting and Handling Precast Concrete Elements”, by CEN/TC 229.
(2)   This EN is intended for safety related applications in which the failure of fastenings will result in collapse or partial collapse of the structure, cause risk to human life or lead to significant economic loss.  In this context it also covers non-structural elements.
(3)   The support of the fixture may be either statically determinate or statically indeterminate. Each support may consist of one fastener or a group of fasteners.
(4)   This EN is valid for applications which fall within the scope of the series EN 1992. In applications where special considerations apply, e.g. nuclear power plants or civil defence structures, modifications may be necessary. The transmission of the fastener loads to the supports of the concrete member shall be shown for the ultimate limit state and the serviceability limit state according to EN 1992-1-1.
(5)   This EN does not cover the design of the fixture. The design of the fixture shall be carried out to comply with the appropriate Standards.
(6)   This document relies on characteristic resistances and distances which are stated in a European Technical Product Specification (see Annex E). At least the characteristics of Annex E, Table E.1 should be given in a European Technical Product Specification providing a basis for the design methods of this EN.
1.2   Type of fasteners and fastening groups
(1)   This EN uses the fastener design theory ) (Figure 1.1) and applies to:
a)   cast-in fasteners such as headed fasteners, anchor channels with rigid connection between anchor and channel;
b)   post-installed mechanical fasteners such as expansion anchors, undercut anchors and concrete screws;
c)   post-installed bonded anchors, bonded expansion anchors and bonded undercut anchors.
NOTE   Connections with post-installed ribbed reinforcing bars should be covered by a European Technical Product Specification and comply with the requirements of EN 1992-1-1.
(2)   For other types of fasteners modifications of the design provisions may be necessary.
(3)   This EN applies to fasteners with established suitability for the specified application in concrete covered by provisions, which refer to this EN and provide data required by this EN. The suitability of the fastener is stated in the relevant European Technical Product Specification.
(...)
(4)   This EN applies to single fasteners and groups of fasteners. In a fastening group the loads are applied to the individual fasteners of the group by means of a common fixture. In this EN it is assumed that in a fastener group only fasteners of the same type and size are used.
The configurations of fastenings with cast-in place headed fasteners and post-installed fasteners covered by this EN are shown in Figure 1.2.
For anchor channels the number of fasteners is not limited.
(...)
NOTE   Configuration with three fasteners is not recommended close to an edge (ci < 100mm) as there are no safe design models for shear loads.
1.3   Fastener dimensions and materials
(1)   This EN applies to fasteners with a minimum diameter or a minimum thread size of 6 mm (M6) or a corresponding cross section. In general, the effective embedment depth should be: hef  40 mm. The actual value for a particular fastener shall be taken from the relevant European Technical Product Specification. In case of post-installed chemical fasteners the effective embedment depth is limited to hef  20dnom. (....)

  • Standard
    129 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    98 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1992-1-1:2005/A1:2015(Amendment)
Eurocode 2: Design of concrete structures - Part 1-1: General rules and rules for buildings
EN 1992-1-1:2004/A1:2014

General rules for the structural design of buildings and civil engineering works in reinforced and prestressed concrete made with normal and lightweight aggregates, plain or lightly reinforced concrete and precast concrete for the design of reinforced concrete components with unbonded tendons.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1994-1-2:2006/A1:2014(Amendment)
Eurocode 4 - Design of composite steel and concrete structures - Part 1-2: General rules - Structural fire design
EN 1994-1-2:2005/A1:2014

Supplementary to Part 1-1. Additional and varied rules to be used for the design of composite structures which are required to avoid premature structural collapse and to limit the spread of fire in the accidental situation of exposure to fire.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1992-2:2005/A101:2011
Eurocode 2 - Design of concrete structures - Part 2:Concrete bridges - Design and detailing rules - National Annex

(101)P Part 2 of Eurocode 2 gives a basis for the design of bridges and parts of bridges in plain, reinforced and prestressed concrete made with normal and light weight aggregates.
(102)P The following subjects are dealt with in Part 2.
Section 1: General
Section 2: Basis of design
Section 3: Materials
Section 4: Durability and cover to reinforcement
Section 5: Structural analysis
Section 6: Ultimate limit states
Section 7: Serviceability limit states
Section 8: Detailing of reinforcement and prestressing tendons — General
Section 9: Detailing of members and particular rules
Section 10: Additional rules for precast concrete elements and structures
Section 11: Lightweight aggregate concrete structures
Section 12: Plain and lightly reinforced concrete structures
Section 113: Design for the execution stages

  • National annex
    4 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    4 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1992-3:2006/A101:2011
Eurocode 2 - Design of concrete structures - Part 3: Liquid retaining and containment structures - National Annex

1.1.2 Scope of Part 3 of Eurocode 2
(101)P Part 3 of EN 1992 covers additional rules to those in Part 1 for the design of structures constructed from plain or lightly reinforced concrete, reinforced concrete or prestressed concrete for the containment of liquids or granular solids.
(102)P Principles and Application Rules are given in this Part for the design of those elements of structure which directly support the stored liquids or materials (i.e. the directly loaded walls of tanks, reservoirs or silos). Other elements which support these primary elements (for example, the tower structure which supports the tank in a water tower) should be designed according to the provisions of Part 1-1.
(103)P This part does not cover:
- Structures for the storage of materials at very low or very high temperatures
- Structures for the storage of hazardous materials the leakage of which could constitute a major health or safety risk.
- The selection and design of liners or coatings and the consequences of the choice of these on the design of the structure.
- Pressurised vessels.
- Floating structures
- Gas tightness
(104) This code is valid for stored materials which are permanently at a temperature between -40 °C and +200 °C.
(105) For the selection and design of liners or coatings, reference should be made to appropriate documents.
(106) It is recognised that, while this code is specifically concerned with structures for the containment of liquids and granular materials, the clauses covering design for liquid tightness may also be relevant to other types of structure where liquid tightness is required.
(107) In clauses relating to leakage and durability, this code mainly covers aqueous liquids.  Where other liquids are stored in direct contact with structural concrete, reference should be made to specialist literature.

  • National annex
    2 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    2 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1992-1-1:2005/AC:2011(Corrigendum)
Eurocode 2: Design of concrete structures - Part 1-1: General rules and rules for buildings
EN 1992-1-1:2004/AC:2010

Eurocode 2 applies to the design of buildings and civil engineering works in plain, reinforced and prestressed concrete. It complies with the principles and requirements for the safety and serviceability of structures, the basis of their design and verification that are given in EN 1990: Basis of structural design.

  • Corrigendum
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1994-1-1:2005/AC:2009(Corrigendum)
Eurocode 4: Design of composite steel and concrete structures - Part 1-1: General rules and rules for buildings
EN 1994-1-1:2004/AC:2009

TC - Editorial and technical modifications to Foreword, Clauses 1, 3, 4, 5, 6, 9 and Annex B.

  • Corrigendum
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1994-2:2005/A101:2009
Eurocode 4 - Design of composite steen and concrete structures - Part 2: General rules and rules for bridges - National annex
  • National annex
    3 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    3 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day