SIST EN 60832-2:2010

SLOVENSKI STANDARD
SIST EN 60832-2:2010
01-junij-2010
Delo pod napetostjo - Izolacijske palice in priklopne naprave - 2. del: Priklopne
naprave (IEC 60832-2:2010)
Live working - Insulating sticks and attachable devices - Part 2: Attachable devices (IEC
60832-2:2010)
Arbeiten unter Spannung - Isolierende Arbeitsstangen und auswechselbare
Adapter/Arbeitsköpfe - Teil 2: Auswechselbare Adapter/Arbeitsköpfe (IEC 60832-2:2010)
Travaux sous tension - Perches isolantes et outils adaptables - Partie 2: Outils
adaptables (CEI 60832-2:2010)
Ta slovenski standard je istoveten z: EN 60832-2:2010
ICS:
13.260 9DUVWYRSUHGHOHNWULþQLP Protection against electric
XGDURP'HORSRGQDSHWRVWMR shock. Live working
29.260.01 (OHNWULþQDRSUHPD]DGHORY Electrical equipment for
SRVHEQLKUD]PHUDKQD working in special conditions
VSORãQR in general
SIST EN 60832-2:2010 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60832-2:2010

---------------------- Page: 2 ----------------------

SIST EN 60832-2:2010

EUROPEAN STANDARD
EN 60832-2

NORME EUROPÉENNE
March 2010
EUROPÄISCHE NORM

ICS 13.260; 29.240.20. Supersedes EN 60832:1996 (partially)


English version


Live working -
Insulating sticks and attachable devices -
Part 2: Attachable devices
(IEC 60832-2:2010)


Travaux sous tension -  Arbeiten unter Spannung -
Perches isolantes et outils adaptables - Isolierende Stangen und auswechselbare
Partie 2: Outils adaptables Adapter/Arbeitsköpfe -
(CEI 60832-2:2010) Teil 2: Auswechselbare
Adapter/Arbeitsköpfe
(IEC 60832-2:2010)




This European Standard was approved by CENELEC on 2010-03-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60832-2:2010 E

---------------------- Page: 3 ----------------------

SIST EN 60832-2:2010
EN 60832-2:2010 - 2 -
Foreword
The text of document 78/839/FDIS, future edition 1 of IEC 60832-2, prepared by IEC TC 78, Live working,
was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60832-2 on
2010-03-01.
This EN 60832-2, together with EN 60832-1, supersedes EN 60832:1996. The two parts have been
created to clearly separate the requirements and testing of insulating sticks from those of attachable
universal devices.

Compared to EN 60832, the major changes included in EN 60832-2 are:
− updating of the list of devices;
− clarifying the applicability of the document to other attachment system than splined end-fitting;
− application of conformity assessment for products having completed the production phase, according
to IEC 61318:2007 (Edition 3), focusing on the classification of defects and the introduction of
alternative testing in case of production follow-up.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2010-12-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2013-03-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60832-2:2010 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60832-2:2010
- 3 - EN 60832-2:2010
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60060-1 - High-voltage test techniques - HD 588.1 S1 -
Part 1: General definitions and test
requirements


IEC 60212 1971 Standard conditions for use prior to and HD 437 S1 1984
during the testing of solid electrical insulating
materials


IEC 60417 Graphical symbols for use on equipment - -
-


IEC 61318 2007 Live working - Conformity assessment EN 61318 2008
applicable to tools, devices and equipment


IEC 61477 - Live working - Minimum requirements for the EN 61477 -
utilization of tools, devices and equipment

---------------------- Page: 5 ----------------------

SIST EN 60832-2:2010

---------------------- Page: 6 ----------------------

SIST EN 60832-2:2010

IEC 60832-2
®
Edition 1.0 2010-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside


Live working – Insulating sticks and attachable devices –
Part 2: Attachable devices

Travaux sous tension – Perches isolantes et outils adaptables –
Partie 2: Outils adaptables

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
XB
CODE PRIX
ICS 13.260; 29.240.20; 29.260.99 ISBN 2-8318-1077-7
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60832-2:2010
– 2 – 60832-2 © IEC:2010
CONTENTS
FOREWORD.5
INTRODUCTION.7
1 Scope.8
2 Normative references .8
3 Terms, definitions and symbols .8
3.1 Terms and definitions .8
3.2 Symbols .9
4 Requirements .9
4.1 General .9
4.2 Dimensional and mechanical requirements.9
4.2.1 Dimensional requirements .9
4.2.2 Mechanical requirements.10
4.3 Mechanical protection .12
4.4 Protection against corrosion .12
4.5 Marking .12
4.6 Instructions for use.12
5 Tests .13
5.1 General .13
5.2 Visual inspection .13
5.3 Dimensional check .13
5.4 Compatibility check .13
5.5 Durability of marking .13
5.6 Mechanical tests and specific tests.14
5.6.1 Universal adaptor and hook stick adaptor .14
5.6.2 Formed-wire ring – Tension of the spigot.15
5.6.3 Locating drift – Bending test .16
5.6.4 Conductor cleaning brush – Semi-tubular type.17
5.6.5 Conductor cleaning brush – V-shaped type – Fatigue test .19
5.6.6 Oilcan – Functioning of the operating lever.19
5.6.7 Ratchet spanner (ratchet wrench) – Friction .19
5.6.8 Spanner (wrench) – Torsion test.20
5.6.9 Retaining pin remover .20
5.6.10 Holding fork – Bending test.24
5.6.11 Retaining device installer/remover – Bending test.24
5.6.12 Binding wire cutter blade (tie wire cutter) – Bending test.25
5.6.13 Rotary blade – Tension test.27
5.6.14 Rotary prong – Tension test.27
5.6.15 Adjustable pliers.28
5.6.16 Vice-grip pliers .29
5.6.17 Adjustable insulator fork .31
5.6.18 All-angle pliers .33
5.6.19 Pin holder.34
5.6.20 Flexible spanner head (flexible wrench head) – Torsion test.36
5.6.21 Ammeter holder .36
5.6.22 Anti-interference braid applicator.39
5.6.23 Hack saw – Bending test .40

---------------------- Page: 8 ----------------------

SIST EN 60832-2:2010
60832-2 © IEC:2010 – 3 –
5.6.24 Mirror .41
5.6.25 Conductor gauge .42
5.6.26 Gap gauge.44
5.6.27 Clevis and tongue stick devices – Tension test.45
5.7 Instructions for use.46
5.7.1 Type test .46
5.7.2 Alternative test in case of attachable devices having completed the
production phase.46
6 Conformity assessment of devices having completed the production phase.46
7 Modifications .46
Annex A (informative) Attachment system of sticks – Examples .47
Annex B (normative) Suitable for live working ; double triangle (IEC 60417–5216
(2002-10)).49
Annex C (normative) Chronology of type tests .50
Annex D (normative) Classification of defects and tests to be allocated .55
Annex E (informative) In-service recommendations.60
Bibliography.61

Figure 1 – Test set-up for a hook stick adaptor – Torsion and tension of the adaptor .14
Figure 2 – Universal adaptor and hook stick adaptor – Torsion of the wing screw .15
Figure 3 – Formed-wire ring – Tension of the spigot .16
Figure 4 – Locating drift – Bending test.17
Figure 5 – Conductor cleaning brush – Fatigue test on semi-tubular type.17
Figure 6 – Conductor cleaning brush – Semi-tubular type – Crushing test.18
Figure 7 – Conductor cleaning brush – V-shaped type – Fatigue test .19
Figure 8 – Spanner (wrench) – Torsion test .20
Figure 9 – Spiral type retaining pin remover – Torsion test .21
Figure 10 – Fine-point type retaining pin remover – Torsion test .22
Figure 11 – Cam type (pry type) retaining pin remover – Bending test .23
Figure 12 – Holding fork – Bending test .24
Figure 13 – Retaining device installer/remover – Bending test .25
Figure 14 – Binding wire cutter blade (tie wire cutter) – Bending test .26
Figure 15 – Rotary blade – Tension test .27
Figure 16 – Rotary prong – Tension test .28
Figure 17 – Adjustable pliers – Tightening capability.28
Figure 18 – Adjustable pliers – Bending test .29
Figure 19 – Vice-grip pliers – Tightening capability – Blocking and unblocking of the
handle .30
Figure 20 – Adjustable insulator fork – Torsion of the attachment system .31
Figure 21 – Adjustable insulator fork – Bending test .32
Figure 22 – Adjustable insulator fork – Articulation test.32
Figure 23 – All-angle pliers – Tightening capability .33
Figure 24 – All-angle pliers – Bending test.34
Figure 25 – Pin holder – Resistance of the spring .35
Figure 26 – Pin holder – Bending test .35

---------------------- Page: 9 ----------------------

SIST EN 60832-2:2010
– 4 – 60832-2 © IEC:2010
Figure 27 – Ammeter holder – Torsion test .36
Figure 28 – Ammeter holder – Shock test .38
Figure 29 – Anti-interference braid applicator – Controlling the sliding rod .39
Figure 30 – Anti-interference braid applicator – Bending test .40
Figure 31 – Hack saw – Bending test mounting.41
Figure 32 – Mirror – Friction test.42
Figure 33 – Conductor gauge – Testing the slide .43
Figure 34 – Conductor gauge – Distortion of the gauge body .43
Figure 35 – Gap gauge – Tension test .44
Figure 36 – Gap gauge – Electrical test .45
Figure A.1 – First example.47
Figure A.2 – Second example .48

Table 1 – Mechanical characteristics of splined end devices (to be supplied by the
manufacturer) .11
Table 2 – Mechanical characteristics of clevis and tongue stick devices (to be supplied
by the manufacturer).12
Table C.1 – Type tests for splined end devices .50
Table C.2 – Type tests for clevis and tongue stick devices.54
Table D.1 – Classification of defects and associated requirements and tests for splined
end devices .55
Table D.2 – Classification of defects and associated requirements and tests for clevis
and tongue stick devices.59

---------------------- Page: 10 ----------------------

SIST EN 60832-2:2010
60832-2 © IEC:2010 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

LIVE WORKING – INSULATING STICKS
AND ATTACHABLE DEVICES –

Part 2: Attachable devices


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60832-2 has been prepared by IEC technical committee 78: Live
working.
The first edition of IEC 60832-1 and that of IEC 60832-2 cancel and replace the first edition of
IEC 60832 published in 1988. The two parts have been created to clearly separate the
requirements and testing of insulating sticks from those of attachable universal devices.
Compared to IEC 60832, the major changes included in IEC 60832-2 are:
• updating of the list of devices;
• clarifying the applicability of the document to other attachment system than splined
end-fitting;
• application of conformity assessment for products having completed the production
phase, according to IEC 61318:2007 (Edition 3), focusing on the classification of
defects and the introduction of alternative testing in case of production follow-up.

---------------------- Page: 11 ----------------------

SIST EN 60832-2:2010
– 6 – 60832-2 © IEC:2010
The text of this standard is based on the following document:
FDIS Voting report
78/839/FDIS 78/845/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 60832 series, published under the general title Live working –
Insulating sticks and attachable devices, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.


IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this publication using a colour printer.

---------------------- Page: 12 ----------------------

SIST EN 60832-2:2010
60832-2 © IEC:2010 – 7 –
INTRODUCTION
The purpose of this standard is to provide essential requirements. Each user of this standard
may supplement it with their own requirements. For example, the user may add requirements
regarding the use of attachable devices on d.c. electrical installations or the mechanical
performance or compatibility and interchangeability with tools already in service. In such
cases, caution should be taken to maintain or improve the performance of the products.
This publication has been prepared in accordance with the requirements of IEC 61477.
The products designed and manufactured according to this standard contribute to the safety
of the users provided they are used by skilled persons, in accordance with safe methods of
work and the instructions for use.
The product covered by this standard may have an impact on the environment during some or
all stages of its life cycle. These impacts can range from slight to significant, be of short-term
or long-term, and occur at the global, regional or local level.
Except for a disposal statement in the instructions for use, this standard does not include
requirements and test provisions for the manufacturers of the product, or recommendations to
the users of the product for environmental improvement. However, all parties intervening in its
design, manufacture, packaging, distribution, use, maintenance, repair, reuse, recovery and
disposal are invited to take account of environmental considerations.

---------------------- Page: 13 ----------------------

SIST EN 60832-2:2010
– 8 – 60832-2 © IEC:2010
LIVE WORKING – INSULATING STICKS
AND ATTACHABLE DEVICES –

Part 2: Attachable devices



1 Scope
This part of IEC 60832 gives the essential requirements for devices that can be attached onto
and removed from the fitting of the insulating sticks for live working, for use on a.c. electrical
installations.
Part 1 of IEC 60832 covers insulating sticks.
In this part of the standard, the term “device” is used for “attachable device”, unless otherwise
specified.
Products designed and manufactured according to this standard contribute to the safety of the
users provided they are used by skilled persons, in accordance with safe methods of work
and the instructions for use.
2 Normative references
The following normative documents contain provisions which, through reference in this text,
constitute provisions of this international standard. For dated references, only the edition cited
applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60060-1, High-voltage test techniques – Part 1: General definitions and test
requirements
IEC 60212:1971, Standard conditions for use prior to and during the testing of solid electrical
insulating materials
IEC 60417, Graphical symbols for use on equipment
IEC 61318:2007, Live working – Conformity assessment applicable to tools, devices and
equipment
IEC 61477, Live working – Minimum requirements for the utilization of tools, devices and
equipment
3 Terms, definitions and symbols
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 61318 and the
following apply.

---------------------- Page: 14 ----------------------

SIST EN 60832-2:2010
60832-2 © IEC:2010 – 9 –
3.1.1
rated value
value of a quantity used for specification purposes, established for a specified set of operating
conditions of a component, device, equipment or system
[IEV 151-16-08]
3.1.2
type of device
family of devices which are of the same design and application and are of similar dimensions
3.2 Symbols
T rated torque given by the manufacturer for a given device and for testing purposes
N
rated tensile force given by the manufacturer for a given device and for testing
F
TN
purposes
rated compression force given by the manufacturer for a given device and for
F
CN
testing purposes
rated bending force given by the manufacturer for a given device and for testing
F
BN
purposes

4 Requirements
4.1 General
The following requirements have been prepared in order that the products covered by this
standard are desig
...