SIST EN IEC 61169-23:2025

SLOVENSKI STANDARD
01-december-2025
Nadomešča:
SIST EN 60169-23:1998
Radiofrekvenčni konektorji - 23. del: Moški in ženski konektor za uporabo pri togih
preciznih koaksialnih vodih z notranjim premerom zunanjega vodnika 3,5 mm
(0,1378 in) (IEC 61169-23:2025)
Radio-frequency connectors - Part 23: Pin and socket connector for use with 3.5 mm
rigid precision coaxial lines with inner diameter of outer conductor of 3.5 mm (0.1378 in)
(IEC 61169-23:2025)
Hochfrequenz-Steckverbinder – Teil 23: Stift- und Buchsenstecker zur Verwendung mit
starren 3,5-mm-Präzisionskoaxialleitungen mit einem Innendurchmesser des
Außenleiters von 3,5 mm (0,1378 in) (IEC 61169-23:2025)
Connecteurs pour fréquences radioélectriques - Partie 23: Connecteur à broche et
connecteur embase pour lignes rigides coaxiales de précision de 3,5 mm avec diamètre
intérieur du conducteur extérieur de 3,5 mm (0,1378 in) (IEC 61169-23:2025)
Ta slovenski standard je istoveten z: EN IEC 61169-23:2025
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61169-23

NORME EUROPÉENNE
EUROPÄISCHE NORM October 2025
ICS 33.120.30 Supersedes EN 60169-23:1993
English Version
Radio-frequency connectors - Part 23: Pin and socket connector
for use with 3,5 mm rigid precision coaxial lines with inner
diameter of outer conductor of 3,5 mm (0,1378 in)
(IEC 61169-23:2025)
Connecteurs pour fréquences radioélectriques - Partie 23: Hochfrequenz-Steckverbinder - Teil 23: Stift- und
Connecteur mâle et connecteur femelle pour lignes Buchsenstecker zur Verwendung mit starren 3,5-mm-
coaxiales rigides de précision de 3,5 mm avec diamètre Präzisionskoaxialleitungen mit einem Innendurchmesser
intérieur du conducteur extérieur de 3,5 mm (0,1378 in) des Außenleiters von 3,5 mm (0,1378 in)
(IEC 61169-23:2025) (IEC 61169-23:2025)
This European Standard was approved by CENELEC on 2025-10-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61169-23:2025 E

European foreword
The text of document 46F/715/FDIS, future edition 1 of IEC 61169-23, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 61169-23:2025.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2026-10-31
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2028-10-31
document have to be withdrawn
This document supersedes EN 60169-23:1993 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61169-23:2025 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60457-5 NOTE Approved as HD 351.5 S1
IEC 61169-15 NOTE Approved as EN IEC 61169-15
IEC 61169-35 NOTE Approved as EN 61169-35
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio frequency connectors - Part 1: Generic EN 61169-1 2013
specification - General requirements and
measuring methods
IEC 62153-4-7 - Metallic cables and other passive components EN IEC 62153-4-7 -
test methods - Part 4-7: Electromagnetic
compatibility (EMC) -Test method for
measuring of transfer impedance ZT and
screening attenuation a or coupling
S
attenuation aC of connectors and assemblies -
Triaxial tube in tube method
IEC 62037-3 - Passive RF and microwave devices, EN IEC 62037-3 -
intermodulation level measurement - Part 3:
Measurement of passive intermodulation in
coaxial connectors
IEC 61169-23 ®
Edition 1.0 2025-08
INTERNATIONAL
STANDARD
Radio-frequency connectors -
Part 23: Pin and socket connector for use with 3,5 mm rigid precision coaxial
lines with inner diameter of outer conductor of 3,5 mm (0,1378 in)
ICS 33.120.30  ISBN 978-2-8327-0665-7

IEC 61169-23:2025-08(en)
IEC 61169-23:2025 © IEC 2025
CONTENTS
FOREWORD . 2
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Mating face and gauge information . 5
4.1 Dimensions – High performance connectors – Grade1 . 5
4.1.1 Connector with pin-centre contact . 5
4.1.2 Connector with socket-centre contact . 6
4.2 Gauge pins for socket-centre contact . 8
4.3 Dimensions – Standard test connectors – Grade 0 . 8
4.3.1 Connector with pin-centre contact . 8
4.3.2 Connector with socket-centre contact . 10
5 Quality assessment procedures. 11
5.1 General . 11
5.2 Ratings and characteristics (see IEC 61169-1:2013, Clause 5) . 11
5.3 Test schedule and inspection requirements . 14
5.3.1 Acceptance tests . 14
5.3.2 Periodic tests . 14
5.3.3 Procedures for the quality conformance. 16
6 Instructions for preparation of detail specifications . 16
6.1 General . 16
6.2 Identification of the component . 17
6.3 Performances . 17
6.4 Marking, ordering information and related matters . 17
6.5 Selection of tests, test conditions and severities . 17
6.6 Blank detail specification pro-forma for type 3,5 series connector . 18
Bibliography . 22

Figure 1 – Connector with pin-centre contact . 5
Figure 2 – Connector with socket-centre contact . 7
Figure 3 – Gauge pin for socket-centre contact . 8
Figure 4 – Connector with pin-centre contact . 9
Figure 5 – Connector with socket-centre contact . 10

Table 1 – Dimensions of connector with pin-centre contact . 6
Table 2 – Dimensions of connector with socket-centre contact . 7
Table 3 – Dimensions of gauge pin for socket-centre contact . 8
Table 4 – Dimensions of connector with pin-centre contact . 9
Table 5 – Dimensions of connector with socket-centre contact . 11
Table 6 – Preferred climatic categories . 11
Table 7 – Rating and characteristics . 12
Table 8 – Acceptance tests . 14
Table 9 – Periodic tests. 15

IEC 61169-23:2025 © IEC 2025
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
Radio-frequency connectors -
Part 23: Pin and socket connector for use with 3,5 mm rigid precision
coaxial lines with inner diameter of outer conductor 3,5 mm (0,1378 in)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and
...