SIST EN 2267-010:2019
(Main)Aerospace series - Cables, electrical, for general purpose - Operating temperatures between -55 °C and 260 °C - Part 010: DR family, single UV laser printable - Product standard
Aerospace series - Cables, electrical, for general purpose - Operating temperatures between -55 °C and 260 °C - Part 010: DR family, single UV laser printable - Product standard
This document specifies the characteristics of UV laser printable electrical lightweight wires DR family for use in the on-board up to 115 V (phase to neutral) or 200 V (phase to phase) AC and 28 Vdc and electrical systems of aircraft at operating temperatures between 65 °C and 260 °C. These cables are demonstrated to be arc resistant in sizes AWG 26 to 14 (115/200 Vac).
In addition, these cables may be suitable for use up to 230/400 Vac in pressurised zones only when installed to take account of possible short circuit effects.
Other electrical system configurations is the responsibility of the users.
Luft- und Raumfahrt - Leitungen, elektrisch, für allgemeine Verwendung - Betriebstemperaturen zwischen -55 °C und 260 °C - Teil 010: DR-Familie Einadrige Leitungen UV-Laser bedruckbar - Produktnorm
Série aérospatiale - Câbles, électriques, d'usage général - Températures de fonctionnement comprises entre -55 °C et 260 °C - Partie 010: Famille DR, fil simple marquable au laser UV - Norme de produit
Le présent document spécifie les caractéristiques des câbles électriques légers, marquables au laser UV, de la famille DR utilisés dans les systèmes électriques de bord des aéronefs jusqu'à 115 Vca (entre phase et neutre) ou 200 Vca (entre phases) et 28 Vcc à des températures de fonctionnement comprises entre 65 °C et 260 °C. Ces câbles de taille 26 à 14 AWG (115/200 Vca) ont démontré leurs résistances aux arcs électriques.
De plus, ces câbles peuvent être utilisés pour des tensions jusqu'à 230/400 Vca dans les zones pressurisées, uniquement quand l’installation tient compte des effets possibles des courts circuits.
Les autres configurations de système électrique sont sous la responsabilité des utilisateurs.
Aeronavtika - Električni kabli za splošno uporabo - Delovne temperature med –55 °C in 260 °C - 010. del: Družina DR, enožilni kabli z možnostjo UV-laserskega tiskanja - Standard za proizvod
Ta evropski standard določa karakteristike družine električnih kablov z možnostjo UV-laserskega tiskanja iz družine DR za uporabo na krovu v električnih sistemih letala z največ 115 V (faza, zvezana z nevtralno napetostjo) ali 200 V (faza, zvezana s fazo) in 28 V DC pri temperaturi delovanja med – 65 °C in 260 °C. Ti kabli so dokazano odporni proti obloku v velikostih od 26 do 14 AWG (115/200 V AC).
Poleg tega se lahko te kable uporablja do največ 230/400 V AC v conah pod tlakom le, če so nameščeni tako, da se upoštevajo možni učinki kratkega stika.
Druge konfiguracije električnih sistemov so odgovornost uporabnikov.
General Information
- Status
- Published
- Publication Date
- 07-Jan-2019
- Technical Committee
- I13 - Imaginarni 13
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 21-Dec-2018
- Due Date
- 25-Feb-2019
- Completion Date
- 08-Jan-2019
Relations
- Effective Date
- 19-Dec-2018
- Effective Date
- 13-Sep-2017
Overview
EN 2267-010:2018 is a CEN aerospace product standard for the DR family single-core, UV laser printable electrical wires intended for aircraft on‑board electrical systems. The standard defines materials, construction, required characteristics and test methods for lightweight copper (or copper alloy) conductors with nickel plating, and insulation systems that can be marked by UV laser. The document’s scope specifies operating temperatures up to 260 °C (the scope text indicates operation between −65 °C and 260 °C), and it applies to use in aircraft AC (up to 115 V phase-to-neutral / 200 V phase-to-phase) and 28 Vdc systems; limited use up to 230/400 Vac may be acceptable in pressurised zones when installation accounts for short-circuit effects.
Key topics and technical requirements
- Conductor and plating: Copper or copper-alloy conductors, nickel plated in accordance with EN 4434 (code D).
- Insulation: Materials and constructions specified to meet thermal, mechanical and electrical requirements; single-core insulation must be UV laser printable for permanent marking.
- Operating temperature range: Up to 260 °C; low temperature performance down to the scope-specified cold limit.
- Size range and AWG mapping: Nominal sections and AWG equivalents are given (codes cover a range including AWG 26 to AWG 2); arc-resistance demonstrated for sizes AWG 26 to AWG 14 at 115/200 Vac.
- Electrical ratings: Intended for on‑board systems up to 115/200 Vac and 28 Vdc; possible 230/400 Vac use only in pressurised zones with appropriate installation considerations.
- Test and qualification: Conformance to test methods in EN 3475-100, EN 2084 and related standards; includes thermal ageing, flammability, wet/dry arc resistance, wet short-circuit, mechanical endurance (bending, abrasion, cut-through), and marking permanence.
- Quality assurance and designation: QA per EN 9133; type codes and marking/packaging conventions defined for procurement and traceability.
Applications and users
- Aerospace OEMs and Tier‑1 suppliers specifying wire and harnesses for fixed‑wing and rotorcraft platforms.
- Electrical design and certification engineers verifying compliance with aircraft environmental, safety and traceability requirements.
- Wire manufacturers and harness assemblers producing UV laser marked, high‑temperature, arc‑resistant wire for aircraft power and signal distribution.
- Maintenance and logistics teams that rely on durable, permanent wire identification for aircraft asset management.
Related standards
- EN 2083 (conductors), EN 2084 (cable technical specification)
- EN 2267-002 (general requirements for series)
- EN 3475-100 (test methods)
- EN 3838 (marking requirements), EN 4434 (lightweight conductors)
- EN 9133 (quality management), TR 6058 (type code guidance)
This standard is essential when specifying aerospace-grade, high-temperature, UV laser printable wiring (EN 2267-010:2018) for reliable, traceable and tested on‑board electrical installations.
Frequently Asked Questions
SIST EN 2267-010:2019 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Aerospace series - Cables, electrical, for general purpose - Operating temperatures between -55 °C and 260 °C - Part 010: DR family, single UV laser printable - Product standard". This standard covers: This document specifies the characteristics of UV laser printable electrical lightweight wires DR family for use in the on-board up to 115 V (phase to neutral) or 200 V (phase to phase) AC and 28 Vdc and electrical systems of aircraft at operating temperatures between 65 °C and 260 °C. These cables are demonstrated to be arc resistant in sizes AWG 26 to 14 (115/200 Vac). In addition, these cables may be suitable for use up to 230/400 Vac in pressurised zones only when installed to take account of possible short circuit effects. Other electrical system configurations is the responsibility of the users.
This document specifies the characteristics of UV laser printable electrical lightweight wires DR family for use in the on-board up to 115 V (phase to neutral) or 200 V (phase to phase) AC and 28 Vdc and electrical systems of aircraft at operating temperatures between 65 °C and 260 °C. These cables are demonstrated to be arc resistant in sizes AWG 26 to 14 (115/200 Vac). In addition, these cables may be suitable for use up to 230/400 Vac in pressurised zones only when installed to take account of possible short circuit effects. Other electrical system configurations is the responsibility of the users.
SIST EN 2267-010:2019 is classified under the following ICS (International Classification for Standards) categories: 29.060.20 - Cables; 49.060 - Aerospace electric equipment and systems. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 2267-010:2019 has the following relationships with other standards: It is inter standard links to SIST EN 2267-010:2017, SIST EN 2267-010:2017. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 2267-010:2019 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.ODVHUVNHJDLuft- und Raumfahrt - Leitungen, elektrisch, für allgemeine Verwendung - Betriebstemperaturen zwischen -55 °C und 260 °C - Teil 010: DR-Familie Einadrige Leitungen UV-Laser bedruckbar - ProduktnormSérie aérospatiale - Câbles, électriques, d'usage général - Températures de fonctionnement comprises entre -55 °C et 260 °C - Partie 010: Famille DR, fil simple marquable au laser UV - Norme de produitAerospace series - Cables, electrical, for general purpose - Operating temperatures between -55 °C and 260 °C - Part 010: DR family, single UV laser printable - Product standard49.060Aerospace electric equipment and systems29.060.20KabliCablesICS:Ta slovenski standard je istoveten z:EN 2267-010:2018SIST EN 2267-010:2019en,fr,de01-marec-2019SIST EN 2267-010:2019SLOVENSKI
STANDARDSIST EN 2267-010:20171DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2267-010
December
t r s z ICS
v {ä r x r Supersedes EN
t t x yæ r s rã t r s yEnglish Version
Aerospace series æ Cablesá electricalá for general purpose æ Operating temperatures between æ w w
¹C and
t x r
¹C æ Part
r s rã DR familyá single UV laser printable æ Product standard Série aérospatiale æ Câblesá électriquesá d 5usage général æ Températures de fonctionnement comprises entre æ w w
¹C et
t x r
¹C æ Partie
r s rã Famille DRá fil simple marquable au laser UV æ Norme de produit
Luftæ und Raumfahrt æ Leitungená elektrischá für allgemeine Verwendung æ Betriebstemperaturen zwischen æ w w
¹C und
t x r
¹C æ Teil
r s rã DRæFamilie Einadrige Leitungen UVæLaser bedruckbar æ Produktnorm This European Standard was approved by CEN on
x August
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
t t x yæ r s rã t r s z ESIST EN 2267-010:2019
Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms, definitions, symbols and abbreviations . 4 4 Materials and construction . 5 5 Required characteristics . 6 6 Quality assurance . 9 7 Designation . 9 8 Identification and marking . 10 9 Packaging, labelling and delivery lengths . 10 10 Technical specification . 10
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...