SIST EN ISO 10669:2001

SLOVENSKI STANDARD
SIST EN ISO 10669:2001
01-julij-2001
2NURJOHUDYQHSRGORåNH]DSORþHYLQVNHYLMDNH]XMHWRSRGORåNRQRUPDOQLKLQ
YHOLNLKPHUUD]UHGL]GHODYH$,62
Plain washers for tapping screw and washer assemblies - Normal and large series -
Product grade A (ISO 10669:1999)
Flache Scheiben für Kombi-Blechschrauben - Normale und große Reihe -
Produkteklasse A (ISO 10669:1999)
Rondelles plates pour vis a tôle a rondelle incorporée - Séries normale et large - Grade A
(ISO 10669:1999)
Ta slovenski standard je istoveten z: EN ISO 10669:1999
ICS:
21.060.30 Podložke, varovalni elementi Washers, locking elements
SIST EN ISO 10669:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10669:2001

---------------------- Page: 2 ----------------------

SIST EN ISO 10669:2001

---------------------- Page: 3 ----------------------

SIST EN ISO 10669:2001

---------------------- Page: 4 ----------------------

SIST EN ISO 10669:2001

---------------------- Page: 5 ----------------------

SIST EN ISO 10669:2001

---------------------- Page: 6 ----------------------

SIST EN ISO 10669:2001
INTERNATIONAL ISO
STANDARD 10669
First edition
1999-08-01
Plain washers for tapping screw and washer
assemblies — Normal and large series —
Product grade A
Rondelles plates pour vis à tôle à rondelle incorporée — Séries normale
et large — Grade A
A
Reference number
ISO 10669:1999(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 10669:2001
ISO 10669:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 10669 was prepared by Technical Committee ISO/TC 2, Fasteners.
©  ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 10669:2001
INTERNATIONAL STANDARD  © ISO ISO 10669:1999(E)
Plain washers for tapping screw and washer assemblies —
Normal and large series — Product grade A
1 Scope
This International Standard specifies the characteristics of plain steel washers of product grade A for tapping screw
and washer assemblies in accordance with ISO 10510.
Normative references
2
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility o
...