SIST EN IEC 60335-2-39:2025/A11:2025

SLOVENSKI STANDARD
01-januar-2025
Gospodinjski in podobni električni aparati - Varnost - 2-39. del: Posebne zahteve
za komercialne električne večnamenske kuhalne posode - Dopolnilo AA
Household and similar electrical appliances - Safety - Part 2-39: Particular requirements
for commercial electric multi-purpose cooking pans
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-39:
Besondere Anforderungen für elektrische Mehrzweck-Koch- und -Bratpfannen für den
gewerblichen Gebrauch
Appareils électrodomestiques et analogues - Sécurité - Partie 2-39: Règles particulières
pour les sauteuses électriques à usage collectif
Ta slovenski standard je istoveten z: EN IEC 60335-2-39:2024/A11:2024
ICS:
97.040.50 Majhni gospodinjski aparati Small kitchen appliances
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60335-2-39:2024/A11

NORME EUROPÉENNE
EUROPÄISCHE NORM November 2024
ICS 97.040.50
English Version
Household and similar electrical appliances - Safety - Part 2-39:
Particular requirements for commercial electric multi-purpose
cooking pans
Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und
Partie 2-39: Exigences particulières pour les sauteuses ähnliche Zwecke - Teil 2-39: Besondere Anforderungen für
électriques à usage commercial elektrische Mehrzweck-Koch- und -Bratpfannen für den
gewerblichen Gebrauch
This amendment A11 modifies the European Standard EN IEC 60335-2-39:2024; it was approved by CENELEC on 2024-08-07. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60335-2-39:2024/A11:2024 E

Contents Page
European foreword . 3
1 Modification to the Introduction . 4
2 Modification to Clause 1, “Scope” . 4
3 Modification to Clause 3, “Terms and definitions” . 4
4 Modification to Clause 7, “Marking and instructions” . 4
5 Modification to Clause 8, “Protection against access to live parts” . 5
6 Modification to Clause 18, “Endurance” . 5
7 Modification to Clause 20, “Stability and mechanical hazards” . 6
8 Modification to Clause 22, “Construction” . 6
9 Modification to annexes . 7
10 Modification to “Bibliography” . 14
European foreword
This document EN IEC 60335-2-39:2024/A11:2024 has been prepared by CLC/TC 61 “Safety of
household and similar electrical appliances”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2025-08-07
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2027-08-07
conflicting with this document have to be
withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document is read in conjunction with EN IEC 60335-2-39:2024 and
EN IEC 60335-2-39:2024/A1:2024.
The numbering system for European clauses, subclauses, notes, tables, figures and annexes that are
additional to those in the IEC standard are prefixed with the letter “Z”.
This document has been prepared under a standardization request addressed to CENELEC by the
European Commission. The Standing Committee of the EFTA States subsequently approves these
requests for its Member States.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
1 Modification to the Introduction
Addition:
With this European amendment A11 the EN 60335-2-39:2003+A1:2004+A2:2008 is superseded.
This European amendment A11 supplements or modifies the corresponding clauses of the standards
below:
— EN 60335-1:2012+A11:2014+A13:2017+A1:2019+A14:2019+A2:2019+A15:2021+A16:2023
(Part 1)
— EN IEC 60335-2-39:2024+A1:2024 (Part 2)
2 Modification to Clause 1, “Scope”
Replace the fourth paragraph starting with “As far as is practicable…”, except Note 102 and Note 103,
with the following:
“This document deals with the reasonably foreseeable hazards presented by appliances that are
encountered by all persons in and around the installation place. However, in general, it does not take
into account:
— children playing with the appliance;
— the use of the appliance by children;
It is recognized that very vulnerable people can have needs beyond the level addressed in this
document.”
Add a new bullet point in Note 103:
“—  gas, oil or solid fuel burning appliances (EN 60335-2-102)”
Add the following new paragraphs:
“Additional requirements for appliances with power driven moving parts are given in Annex ZE.
This document does not deal with any specific requirements on noise emitted from these appliances
the generated noise is not considered to be a relevant hazard. Thus, the emission sound pressure
level LpA is considered to be LpA ≤ 70 dB(A).”
3 Modification to Clause 3, “Terms and definitions”
In 3.103, replace the definition with the following:
installation wall
fixed construction containing supply facilities for wall mounted appliances on one or both sides
4 Modification to Clause 7, “Marking and instructions”
7.12
Add the following:
The front cover of the instructions shall include the substance of the following:
CAUTION: Read the instructions before using the appliance
This wording may be replaced by symbols ISO 7000-0434A (2004-01) and ISO 7000-0790 (2016-08).
Add the following:
The instructions shall also state the maximum weight of the empty appliance.
Replace the modification with the following:
This appliance is not intended for use by persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Replace the fifth paragraph of the addition by the following:
If any of symbols IEC 60417-5021 (2002-10), ISO 7000-0434A (2004-01) or ISO 7000-0790 (2016-08)
are used on the product or in the instructions, their meaning shall be explained.
Add the following:
The instructions shall also state
— the intended use of the appliance as covered by the scope of this document;
— instructions regarding user maintenance and operation of the appliance and, if necessary,
instructions for the training of operators;
— instructions designed to enable adjustment and maintenance to be carried out safely, including
the protective measures that should be taken during these operations;
— the conditions under which the appliance is stable during use, dismantling when out of use,
testing or foreseeable breakdowns;
— the operating method to be followed in the event of accident or breakdown to prevent unsafe
actions;
— information regarding the use of personal protection equipment in case of spreading hot food
stuff;
— a warning concerning possible slippery floor adjacent to the appliance.
7.12.1 Add the following:
The instructions for table-top appliances shall state that a support is needed so that the working height
of the appliance is between 695 and 980 mm.
The instructions shall state that any repairs shall be carried out by competent persons.
7.12.Z101
The instructions shall include the possible reasonably foreseeable misuse and, whenever relevant, a
warning against the effects it may have on the safe use of the appliance. At least, it shall include the
substance of the following:
WARNING: Appliances must be disconnected from their power supply during cleaning or
maintenance and when replacing parts.
Compliance is checked by inspection.
5 Modification to Clause 8, “Protection against access to live parts”
8.1.1 Addition
Add in the third paragraph starting with “Test probe B and probe 18 of EN 61032.“ the following:
Test probe 18 is not applicable unless the appliance is intended to be installed in an area open to the
public
6 Modification to Clause 18, “Endurance”
Replace the sentence in Part 2 with “This clause of Part 1 is not applicable.“.
7 Modification to Clause 20, “Stability and mechanical hazards”
20.2 Addition
In the second dashed item starting with “test probe 18 of EN 61032.“, add the following:
Test probe 18 is not applicable unless the appliance is intended to be installed in an area open to the
public
8 Modification to Clause 22, “Construction”
22.13 Modification
Add the following:
Lids shall be equipped with at least one handle.
In the addition replace “grips” with “handle(s)”.
22.48 Addition
After the first paragraph, add the following:
For appliances within the scope of this document without cleaning system, Fluid Category is 2
according to EN 61770:2009 .
For appliances within the scope of this document with cleaning system, Fluid Category is 3 according
to EN 61770:2009Error! Bookmark not defined.
22.106 Add the following as a second paragraph:
This requirement is met, if:
— the hinge incorporates a click stop; or
— the lid is counter balanced; or
— the lid can be opened through an angle of at least 100°.
Replace the compliance criteria with the following and add the note:
Compliance is checked by applying a force of 20 N in the most unfavourable position and direction to
the raised lid. The lid shall not fall back to its operating position.
NOTE Lids that can be opened through an angle of at least 100°, even if placed against a wall, are not
subjected to this test.
22.Z.101 Appliances shall meet the following ergonomic requirements:
— The working height of the appliance shall be between 695 and 980 mm,
— The rear edge of the pan shall be a maximum of 850 mm from the front edge of the appliance,
— Operator controls shall be
— attached at a minimum height of 350 mm,
— clearly visible and identifiable,
— positioned within easy reach of the operator's hand

As impacted by EN 61770:2009/AC:2011, EN 61770:2009/A11:2018, EN 61770:2009/A1:2019 and
EN 61770:2009/A12:2022.
— secured against accidental actuation, if their actuation could result in a hazard.
Compliance is checked by inspection.
22.Z.102 Appliances shall meet hygiene requirements.
Compliance is checked by inspection and by the requirements in Annex ZAA.
22.Z.103 Filling and draining taps shall be designed and constructed so that it is not possible to
inadvertently open them.
Compliance is checked by inspection and by manual test.
NOTE For example, this requirement is met when the valve handle is such that, when released, it returns
automatically to the closed position or is of the wheel type or is placed in a recess.
9 Modification to annexes
The annexes of Part 1 are applicable except as follows:
Annex ZC
(normative)
Normative references to international publications with their
corresponding European publications
Annex ZC of Part 1 is applicable with the following additions:
Publication Year Title EN/HD Year
IEC 60584-1 - Thermocouples – Part 1: EN 60584-1 2013
EMF specifications and tolerances
ISO 185 2020 Grey cast irons – Classifications - -
ISO 898-1 - Mechanical properties of fasteners made of EN ISO 898-1 2013
carbon steel and alloy steel – Par 1: Bolts,
+ AC 2013
...