iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 50091-2:1997

(Main)

Uninterruptible power systems (UPS) -- Part 2: EMC requirements

Uninterruptible power systems (UPS) -- Part 2: EMC requirements

This EMC Standard applies to single UPS units or UPS systems comprising a number of interconnected UPS and associated control/switchgear forming a single power system, intended to be installed in any operator accessible area or in separated electrical locations, connected to either industrial or public low voltage supply networks. This product EMC Standard will take precedence over all aspects of the Generic Standards and no additional testing is necessary. The requirements have been selected so as to ensure an adequate level of electromagnetic compatibility (EMC) for UPS at public and industrial locations. These levels cannot however cover extreme cases which may occur in any location, but with extremely low probability. It takes account of the differing test conditions necessary to encompass the range of physical sizes and power ratings of UPS. A UPS unit or system shall meet the relevant requirements of this Standard as a stand-alone product. EMC phenomena produced by any customers' load connected to the output of the UPS equipment shall not be taken into account. Special installation environments are not covered nor are fault conditions of UPS taken into account. This Standard does not cover DC supplied electronic ballasts (IEC 924 and IEC 925) or UPS based on rotating machines.

Unterbrechungsfreie Stromversorgungssysteme(USV) -- Teil 2: EMV-Anforderungen

Alimentations sans interruption (ASI) -- Partie 2: Prescriptions pour la compatibilité électromagnétique (CEM)

Uninterruptible Power Systems (UPS) - Part 2: EMC requirements

General Information

Status
Withdrawn
Publication Date
28-Feb-1997
Withdrawal Date
23-Feb-2009
ICS
29.200 - Rectifiers. Convertors. Stabilized power supply
33.100.01 - Electromagnetic compatibility in general
Technical Committee
EMC - Electromagnetic compatibility
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
06-Feb-2009
Due Date
01-Mar-2009
Completion Date
24-Feb-2009
Directive
2004/108/EU - DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
89/336/EEC - Electromagnetic compatibility (EMC)
Mandate
BC/CLC/92-02 - BC/CLC/92-02
Ref Project
EN 50091-2:1995 - Uninterruptible power systems (UPS) - Part 2: EMC requirements

Relations

Replaced By
SIST EN 62040-2:2006 - Uninterruptible power systems (UPS) -- Part 2: Electromagnetic compatibility (EMC) requirements
Effective Date
29-Jan-2023

Buy Standard

EN 50091-2:1997EN 50091-2:1997
PreviousNext
Standard
EN 50091-2:1997
English language
40 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50091-2:1997
01-marec-1997
Uninterruptible Power Systems (UPS) - Part 2: EMC requirements
Uninterruptible power systems (UPS) -- Part 2: EMC requirements
Unterbrechungsfreie Stromversorgungssysteme(USV) -- Teil 2: EMV-Anforderungen
Alimentations sans interruption (ASI) -- Partie 2: Prescriptions pour la compatibilité
électromagnétique (CEM)
Ta slovenski standard je istoveten z: EN 50091-2:1995
ICS:
29.200 8VPHUQLNL3UHWYRUQLNL Rectifiers. Convertors.
6WDELOL]LUDQRHOHNWULþQR Stabilized power supply
QDSDMDQMH
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 50091-2:1997 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 2 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 3 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 4 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 5 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 6 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 7 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 8 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 9 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 10 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 11 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 12 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 13 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 14 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 15 ----------------------

SIST EN 50091-2:1997

---------------------- Page: 16 ----------------------

SIST EN 50091-2:1997

---------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 61204-3:2018(Main)
Low voltage power supplies, d.c. output - Part 3: Electromagnetic compatibility (EMC) (IEC 61204-3:2016)
EN IEC 61204-3:2018

Specifies electromagnetic compatibility (EMC) requirements for power supply units (PSUs) providing d.c. output(s) up to 200 V at a power level of up to 30 kW, operating from a.c. or d.c. source voltages of up to 600 V.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62040-2:2018(Main)
Uninterruptible power systems (UPS) - Part 2: Electromagnetic compatibility (EMC) requirements (IEC 62040-2:2016)
EN IEC 62040-2:2018

Is intended as a product standard allowing the EMC conformity assessment of products of categories C1, C2 and C3 as defined in this part of EN 62040, before placing them on the market.The requirements have been selected so as to ensure an adequate level of electromagnetic compatibility (EMC) for UPS at public and industrial locations.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61800-3:2018(Amendment)
Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods (IEC 61800-3:2017)
EN IEC 61800-3:2018

specifies electromagnetic compatibility (EMC) requirements for power drive systems (PDSs). A PDS is defined in 3.1. These are adjustable speed a.c. or d.c. motor drives. Requirements are stated for PDSs with converter input and/or output voltages (line-to-line voltage), up to 35 kV a.c. r.m.s.

  • Standard
    126 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    126 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62310-2:2008(Main)
Static transfer systems (STS) -- Part 2: Electromagnetic compatibility (EMC) requirements
EN 62310-2:2007

The IEC 62310 series applies to free standing operation a.c. static transfer systems (STS) intended to ensure the continuity of load supply through controlled transfer, with or without interruption of power, from two or more independent a.c. sources. The IEC 62310 series includes requirements for the switching elements, their control and protective elements, where applicable. The IEC 62310 series also includes information for the overall integration of the STS and its accessories into the a.c. power network. This standard applies to systems up to 1 000 V a.c. which are intended to be used in singlephase, phase-phase or three-phase applications This part of IEC 62310 takes precedence over all aspects of the generic standards, and no additional testing is necessary. The requirements have been selected so as to ensure an adequate level of Electromagnetic Compatibility (EMC) for STS at public and industrial locations. These levels cannot, however, cover extreme cases which may occur in any location, but with extremely low probability of occurrence. It takes into account the differing test conditions necessary to encompass the range of physical sizes and power ratings of STS. A STS, whether presented as a unit or an assembly of units shall meet the relevant requirements of this part of IEC 62310 as a stand-alone product. EMC phenomena produced by any supply or load connected to the input or output of the STS equipment shall not be taken into account.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN IEC 62909-3:2023(Main)
Bi-directional grid connected power converters - Part 3: EMC requirements and test methods
prEN IEC 62909-3:2023
  • Draft
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
kSIST FprEN IEC 61800-3:2022(Main)
Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods for PDS and machine tools
FprEN IEC 61800-3:2022

IEC 61800-3:2022 specifies electromagnetic compatibility (EMC) requirements for adjustable speed power drive systems (PDSs) and machine tools (MTs). A PDS is an AC or DC motor drive including an electronic converter. Requirements are stated for AC and DC PDSs and MTs with input and/or output voltages (line-to-line voltage), up to 35 kV AC RMS. This document applies to equipment of all power ratings.
As a product EMC standard, this document can be used for the assessment of PDS and MT. It can also be used for the assessment of complete drive modules (CDM) or basic drive modules (BDM).
Traction applications and electric vehicles are excluded. Equipment which is defined as group 2 in CISPR 11:2015 is excluded.
This document does not give requirements for the electrical machine which converts power between the electrical and mechanical forms within the PDS. Requirements for rotating electrical machines are covered by the IEC 60034 series. In this document, the term "motor" is used to describe the electrical machine, whether rotary or linear, and regardless of the direction of power flow.
This document is applicable to BDMs, CDMs, PDSs and MTs with or without radio function. However, this document does not specify any radio transmission and reception requirements.
This document defines the minimum requirements for emission and immunity in the frequency range from 0 Hz to 400 GHz. Tests are not required in frequency ranges where no requirements are specified.
This fourth edition cancels and replaces the third edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:


       
  1. extension of the scope to machine tools with one or more embedded PDS;

    2.    
  2. extension of the frequency range for radiated immunity tests to 6 GHz;

    3.    
  3. general updates in the normative part and the informative annexes.

  • Draft
    123 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 12349:2023(Main)
Mechanical vibration - Guide to the health effects of vibration on the human body
CEN/TR 12349:2023

The aim of this CEN report is to provide information on the possible adverse health effects caused by exposure to vibration at work.  the report addresses manufacturers as well as employers and employees using vibrating machinery in order to improve their understanding of the possible health problems arising from occupational exposure to vibration.

  • Technical report
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 80004-1:2023(Main)
Nanotechnologies - Vocabulary - Part 1: Core vocabulary (ISO 80004-1:2023)
EN ISO 80004-1:2023

This document defines core terms in the field of nanotechnology. This document is intended to facilitate communication between organizations and individuals in industry and those who interact with them.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3262-4:2023(Main)
Extenders - Specifications and methods of test - Part 4: Whiting (ISO 3262-4:2022)
EN ISO 3262-4:2023

This document specifies requirements and corresponding methods of test for whiting.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 1247-1:2023(Main)
Aluminium pigments for paints - Part 1: General aluminium pigments (ISO 1247-1:2021)
EN ISO 1247-1:2023

This document specifies the requirements and corresponding test methods for aluminium pigments suitable for use in paints including:
a) general, decorative and protective paints, and
b) special finishing paints.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day