SIST EN ISO 9994:2019

SLOVENSKI STANDARD
01-marec-2019
1DGRPHãþD
SIST EN ISO 9994:2006
SIST EN ISO 9994:2006/A1:2008
Vžigalniki - Varnostna specifikacija (ISO 9994:2018)
Lighters - Safety specification (ISO 9994:2018)
Feuerzeuge - Festlegungen für die Sicherheit (ISO 9994:2018)
Briquets - Spécifications de sécurité (ISO 9994:2018)
Ta slovenski standard je istoveten z: EN ISO 9994:2019
ICS:
97.180 Razna oprema za dom in Miscellaneous domestic and
trgovino commercial equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 9994
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2019
EUROPÄISCHE NORM
ICS 97.180 Supersedes EN ISO 9994:2006
English Version
Lighters - Safety specification (ISO 9994:2018)
Briquets - Spécifications de sécurité (ISO 9994:2018) Feuerzeuge - Festlegungen für die Sicherheit (ISO
9994:2018)
This European Standard was approved by CEN on 19 December 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9994:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 9994:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 355 “Lighters” the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2019, and conflicting national standards shall be
withdrawn at the latest by July 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 9994:2006.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 9994:2018 has been approved by CEN as EN ISO 9994:2019 without any modification.

INTERNATIONAL ISO
STANDARD 9994
Fifth edition
2018-12
Lighters — Safety specifications
Briquets — Spécifications de sécurité
Reference number
ISO 9994:2018(E)
©
ISO 2018
ISO 9994:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 9994:2018(E)
Contents  Page
Foreword .v
Introduction .vi
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Functional requirements . 3
4.1 Flame generation . 3
4.2 Flame heights . 3
4.2.1 Non-adjustable lighters . . 4
4.2.2 Adjustable lighters . 4
4.3 Flame-height adjustment . 6
4.4 Resistance to spitting or sputtering and flaring . 7
4.5 Flame extinction . 7
4.6 Volumetric displacement of fuel . 8
4.7 Mass of fuel . 8
5  Structural integrity requirements . 8
5.1 External finish . 8
5.2 Compatibility with fuel . 8
5.3 Resistance to fuel loss . 8
5.4 Resistance to dropping . 9
5.5 Resistance to elevated temperature . 9
5.6 Resistance to internal pressure . 9
5.7 Burning behaviour . 9
5.8 Resistance to cyclic burning .10
5.9 Resistance to continuous burning .10
6  Test methods .11
6.1 Test specimens and test sequencing .11
6.1.1 Test specimens.11
6.1.2 Test sequencing.11
6.2 Flame height measurement .11
6.2.1 Apparatus .11
6.2.2 Procedure .11
6.3 Spitting, sputtering and flaring tests .11
6.3.1 General.11
6.3.2 Procedure .11
6.4 Flame extinction test.12
6.4.1 Apparatus .12
6.4.2 Procedure .12
6.5 Fuel compatibility test .13
6.5.1 General.13
6.5.2 Apparatus .13
6.5.3 Procedure .13
6.6 Refilling test .15
6.6.1 General.15
6.6.2 Apparatus .15
6.6.3 Procedure .15
6.7 Volumetric fuel-displacement test .16
6.7.1 General.16
6.7.2 Test specimens.16
6.7.3 Apparatus .16
6.7.4 Procedure .16
6.8 Drop test .17
ISO 9994:2018(E)
6.8.1 General.17
6.8.2 Apparatus .17
6.8.3 Procedure .18
6.9 Elevated-temperature test .19
6.9.1 General.19
6.9.2 Apparatus .19
6.9.3 Procedure .19
6.10 Internal-pressure test .20
6.10.1 General.20
6.10.2 Test specimens.20
6.10.3 Apparatus .20
6.10.4 Procedure .20
6.11 Cyclic-burning-time test .21
6.11.1 General.21
6.11.2 Procedure .21
6.12 Continuous-burning-time test .22
6.12.1 General.22
6.12.2 Apparatus .22
6.12.3 Procedure .22
7  Instructions and warnings .23
7.1 General .23
7.2 Location .23
7.3 Content .23
7.4 Safety signs .24
7.5 Refilling instructions .25
7.5.1 General.25
7.5.2 Fluid lighters .25
7.5.3 Gas lighters .25
8  Product marking .25
Annex A (normative) Test sequencing .26
iv © ISO 2018 – All rights reserved

ISO 9994:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 4, Burning
behaviour.
This fifth edition cancels and replaces the fourth edition (ISO 9994:2005), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— Clause 2, 3.22, 3.23, subclause 4.2.2.4, subclause 4.2.3, subclause 4.2.4, subclause 4.7, subclause 6.1.2,
subclause 6.11.2.2.9 and subclause 6.11.2.2.10 have been added.
— term number 3.6, subclause 4.2.2.3, subclause 4.5, subclause 5.1, subclause 5.7, Figure 4,
subclause 6.3.2.7, subclause 6.7.4, subclause 6.9.3.3, subclause 6.10.4, subclause 6.12.3, subclause 7.3.1,
subclause 7.4, Figure 5, Figure 7 and Annex A have been modified.
— Bibliography has been deleted.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
ISO 9994:2018(E)
Introduction
Lighters, being flame-producing devices, can, as do all flame sources, present a potential hazard to
users. The safety specifications given in this document cannot eliminate all hazards, but are intended
to reduce potential hazards to users.
This document is intended to be revised periodically to consider flame height reduction for the various
technologies in line with technological progress.
vi © ISO 2018 – All rights reserved

INTERNATIONAL STANDARD ISO 9994:2018(E)
Lighters — Safety specifications
WARNING — Persons using this document should be familiar with normal laboratory practice, if
applicable. This document does not purport to address all the safety concerns, if any, associated
with its use. It is the responsibility of the user to establish appropriate safety and health
practices and to determine the applicability of any other restrictions.
1  Scope
This document specifies requirements for lighters to ensure a reasonable degree of safety for normal
use or reasonably foreseeable misuse of such lighters by users.
This document applies to all flame-producing products commonly known as cigarette lighters, cigar
lighters and pipe lighters.
It does not apply to matches and flame-producing products intended solely for igniting materials other
than cigarettes, cigars, and pipes.
2  Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 7941, Commercial propane and butane — Analysis by gas chromatography
UL 1439, Tests for Sharpness of Edges on Equipment
3  Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
lighter
manually operated flame-producing device, employing a petrochemical derivative as a fuel, normally
used for deliberately igniting cigarettes, cigars and pipes, and which might foreseeably be used to ignite
(3.21) materials such as paper, wicks, candles and lanterns
Note 1 to entry: Lighters are specifically not intended for use as candles or as flashlights, or for other uses
requiring an extended burn time.
3.2
fluid lighter
lighter (3.1), with an exposed wick, that employs as fuel liquid hydrocarbons such as hexane whose
gauge vapour pressure at 24 °C does not exceed 34,5 kPa
3.3
gas lighter
lighter (3.1) that employs as fuel liquefied hydrocarbons such as n-butane, isobutane and propane
whose gauge vapour pressure at 24 °C exceeds 104 kPa
ISO 9994:2018(E)
3.4
postmixing burner lighter
gas lighter (3.3) in which fuel is supplied for combustion and air is supplied at the point of combustion
3.5
premixing burner lighter
gas lighter (3.3) in which fuel and air are mixed before being supplied for combustion
3.6
non-refillable lighter
disposable lighter
lighter (3.1) marketed with an integral supply of fuel and that is not intended to be refilled with fuel
3.7
refillable lighter
lighter (3.1) intended to be refuelled either by transferring fuel from an external container or by
inserting a new prefilled fuel reservoir
3.8
adjustable lighter
lighter (3.1) provided with a mechanism for the user to vary the flame height (3.13)
3.9
non-adjustable lighter
lighter (3.1) that is not provided with a user-accessible mechanism to adjust the flame height (3.13)
Note 1 to entry: The flame height is preset by the manufacturer.
3.10
automatically adjusting pipe lighter
lighter (3.1) characterized by an automatic increase in flame height (3.13) when tilted from an upright
position, designed specifically for lighting pipes
3.11
self-extinguishing lighter
lighter (3.1) that, once ignited, requires continuous intentional and positive action to maintain a flame
(3.20) and that is subsequently extinguished by the termination of such positive action
3.12
non-self-extinguishing lighter
lighter (3.1) that, once ignited, does not require intentional or positive action by the user to maintain a
flame (3.20) and requires a subsequent deliberate user action to extinguish the flame
3.13
flame height
linear distance from the tip of the visible flame (3.20) to the top of the shield or, in the absence of a
shield, from the tip of the visible flame to the bottom of the exposed wick or the top of the burner valve
orifice (3.16)
3.14
shield
structure that totally or partially surrounds the burner valve orifice (3.16) of a gas lighter (3.3) or the
wick of a fluid lighter (3.2)
3.15
burner valve
component of a gas lighter (3.3) which controls the release of fuel
3.16
burner valve orifice
tip of the burner valve (3.15) from which fuel is released
2 © ISO 2018 – All rights reserved

ISO 9994:2018(E)
3.17
flaring
variation of flame height (3.13) from the steady-state flame condition
3.18
sustained self-ignition
propagation of a flame (3.20) by other than deliberate manual operation so as to cause the ignition
element to be activated and the flame to continue to burn
EXAMPLE By dropping the lighter.
3.19
spitting
sputtering
flame phenomenon of a gas lighter (3.3) wherein the escape of non-evaporated liquefied gas produces a
shower of burning liquid droplets which separate from the main flame
3.20
flame
result of combustion of fuel that produces heat and often light which could be visible with the naked eye
under normal or subdued lighting conditions
3.21
ignite
to produce a flame (3.20) with a lighter (3.1) by activating the self-contained ignition and fuel release
systems of that lighter in the intended manner
3.22
dual flame type lighter
lighter (3.1) that employs a burner valve system(s) that produces more than one type of flame
(premixing and postmixing), which could be produced independently and separately (one flame type at
a time), or dependently and concurrently (multiple flame types at a time)
3.23
multiple flame type lighter
lighter (3.1) that employs a burner valve system(s) that produces more than one flame of the same type
of flame (premixing or postmixing), which could be produced independently and separately (one flame
at a time), or dependently and concurrently (multiple flames at a time)
4  Functional requirements
4.1  Flame generation
In order to minimize the possibility of inadvertent ignition, or self-ignition, lighters shall require a
deliberate manual operation to produce a flame. This operation shall conform to at least one of the
following requirements:
a) positive action on the part of the user shall be required to generate and maintain a flame;
b) two or more independent actions by the user shall be required to generate a flame;
c) an actuating force equal to, or greater than, 15 N shall be required to generate a flame (see Figure 1
or Figure 2).
4.2  Flame heights
NOTE Maximum flame heights specified in this document, for both postmixing burner lighters and
premixing burner lighters, are intended to be reconsidered periodically with a view to gradual reduction in line
with technological progress.
ISO 9994:2018(E)
4.2.1  Non-adjustable lighters
4.2.1.1  Non-adjustable fluid lighters shall not be capable of producing a flame height greater than
120 mm when tested in accordance with 6.2.
4.2.1.2  Non-adjustable, postmixing and premixing burner lighters shall not be capable of producing a
flame height greater than 50 mm when tested in accordance with 6.2.
4.2.2  Adjustable lighters
4.2.2.1  For adjustable lighters as defined in 3.8, the maximum flame height that a user will obtain
under different conditions of use shall comply with the following requirements when tested in
accordance with 6.2.
4.2.2.2  Adjustable (refillable or non-refillable) postmixing burner lighters shall have the flame height
adjusted by the manufacturer in such a manner that the lighter, when first ignited by the user — without
changing the adjustment — will not produce a flame height greater than 100 mm.
4.2.2.3  Adjustable refillable postmixing burner lighters shall not be capable of producing a flame
height greater than 120 mm when deliberately adjusted by the user to the manufacturer’s design limit
for maximum flame height.
4.2.2.4  Adjustable non-refillable postmixing burner lighters shall not be capable of producing a flame
height greater than 100 mm when deliberately adjusted by the user to the manufacturer’s design limit
for maximum flame height.
4 © ISO 2018 – All rights reserved

ISO 9994:2018(E)
Key
1 lighter
2 mass
F flame-generation actuating force
Figure 1 — Application of flame-generation actuating force as specified in 4.1 c) — Push-button
actuator
Key
1 force gauge
F flame-generation actuating force
Figure 2 — Application of flame-generation actuating force as specified in 4.1 c) — Rotary
actuator
ISO 9994:2018(E)
4.2.2.5  Adjustable premixing burner lighters shall have the flame height adjusted by the manufacturer
in such a manner that the lighter, when first ignited by the user — without changing the adjustment —
will not produce a flame height greater than 60 mm.
4.2.2.6  Adjustable premixing burner lighters shall not be capable of producing a flame height greater
than 75 mm when deliberately adjusted by the user to the manufacturer’s design limit for maximum
flame height.
4.2.2.7  Adjustable postmixing and premixing burner lighters shall not be capable of producing a flame
height greater than 50 mm when set at the lowest possible flame height.
4.2.2.8  Automatically adjusting pipe lighters shall not be capable, in any position, of producing a flame
height greater than 100 mm.
4.2.2.9  The maximum attainable flame height for lighters shall be limited by pre-setting or by product
design, or both.
4.2.3  Dual flame type lighter
For each type of flame of a dual flame type lighter, the flame height shall comply with the corresponding
requirement for that type of flame provided in 4.2.1 or 4.2.2.
4.2.4  Multiple flame type lighter
For multiple flame type lighters, the flame height of each flame shall comply with the corresponding
requirement provided in 4.2.1 or 4.2.2.
4.3  Flame-height adjustment
4.3.1  Adjustable lighters as defined in 3.8 shall require a deliberate action on the part of the user either
to decrease or to increase the flame height when used in the normal manner. Adjustable lighters shall
bear an indication showing the direction of movement of the adjusting mechanism required to produce a
higher or lower flame.
4.3.2  On lighters whose adjusting mechanisms conform to 4.3.3 and 4.3.4, the direction of movement
shall be permanently imprinted or engraved on the lighter in the vicinity of the adjusting mechanism and
readily visible and understandable.
4.3.3  Gas lighters having rotary-movement flame-control actuators approximately at right-angles to
the flame shall perform as follows:
a) when the flame-control actuator is at the top of the lighter and the lighter is held so that the flame is
oriented vertically upward, and the user is facing the flame-control actuator, moving the actuator
to the left shall produce a decrease in flame height;
b) when the flame-control actuator is at the bottom of the lighter, and the lighter is held so that the
user is facing the actuator, a clockwise movement shall produce a decrease in flame height.
4.3.4  For gas lighters requiring movement of the flame-control actuator approximately parallel to the
flame axis, the flame height shall decrease or increase in accordance with the direction of the movement.
4.3.5  If the flame-control actuator protrudes from the body of the lighter, it shall require a minimum
actuating force of 1 N applied over the entire range of adjustment in a tangential direction (see Figure 3).
6 © ISO 2018 – All rights reserved

ISO 9994:2018(E)
4.4  Resistance to spitting or sputtering and flaring
Gas lighters as defined in 3.3, when set at the maximum flame height, shall exhibit no spitting or
sputtering as defined in 3.19, or flaring as defined in 3.17, when tested in accordance with 6.3.
Key
1 direction of flame-control actuating force
Figure 3 — Application of flame-control actuating force as specified in 4.3.5
4.5  Flame extinction
When a lighter is extinguished in the intended manner, for example by closing a cover or by releasing a
button or a lever, it shall meet the following requirements with respect to extinction time.
a) Non-adjustable fluid and postmixing burner lighters, at their permanently set flame heights, when
tested in accordance with 6.4, shall have any exposed flame completely extinguished within 2 s
after a 10 s burn.
b) Adjustable postmixing burner lighters, when tested in accordance with 6.4, shall have any flame
completely extinguished within 2 s:
1) after a 10 s burn when set at a flame height of 50 mm, or the maximum flame height the
adjustment allows if lower than 50 mm;
2) after a 5 s burn when set at maximum flame height.
c) In the case of postmixing burner lighters that have shields, an additional 2 s afterburn (i.e.
continuous burning) is acceptable if the flame, during this additional 2 s period, does not extend
above the shield.
d) Non-adjustable premixing burner lighters, at their permanently set flame heights, when tested
in accordance with 6.4, shall have any flame completely extinguished in no more than 5 s after a
10 s burn.
e) Adjustable premixing burner lighters, when tested in accordance with 6.4, shall have any flame
completely extinguished in no more than 5 s:
1) after a 10 s burn when set at a flame height of 50 mm, or the maximum flame height the
adjustment allows if lower than 50 mm;
2) after a 5 s burn when set at maximum flame height.
ISO 9994:2018(E)
NOTE In the case of premixing burner gas lighters, the total afterburn time in this document is intended
to be reconsidered periodically with a view to gradual reduction in line with technological progress.
f) In the case of dual flame type lighters, the extinction time of each type of flame shall comply with
the corresponding requirement for that type of flame provided in this subclause.
g) In the case of multiple flame type lighters, the extinction time of each flame shall comply with the
corresponding requirement for that type of flame provided in this subclause.
4.6  Volumetric displacement of fuel
For gas lighters shipped with fuel, the liquid portion of the fuel shall not exceed 85 % of the volumetric
capacity of the fuel reservoir when tested in accordance with 6.7.
4.7  Mass of fuel
For gas lighters shipped with fuel, the mass of liquefied fuel shall not exceed 10 g.
5  Structural integrity requirements
5.1  External finish
Lighters shall have no external sharp edges that could cause accidental cuts or abrasions to the user
when handled or used in the intended manner. If a potential sharp edge is found it shall be tested
according to UL 1439.
NOTE UL refers to Underwriters Laboratories.
5.2  Compatibility with fuel
5.2.1  Components of fluid lighters as defined in 3.2 that come into contact with the fuel recommended
by the manufacturer shall not, after extended contact with that fuel, deteriorate so as to cause the lighter
to fail any of the criteria contained in this document, when tested in accordance with 6.5.
5.2.2  Components of gas lighters as defined in 3.3 that come into contact with the fuel recommended
by the manufacturer shall not deteriorate after exposure to the fuel, so as to cause the lighter to fail any
of the criteria contained in this document or allow gas escape exceeding 15 mg/min, when tested in
accordance with 6.5.
5.2.3  Lighters that meet the requirements of 5.2.1 and 5.2.2 and that are able to be ignited in the
intended manner shall subsequently meet all the applicable requirements of 4.1 to 4.5, inclusive. Lighters
that are not able to be ignited in the intended manner do not constitute a failure.
5.3  Resistance to fuel loss
5.3.1  Refillable fluid lighters having a sealed fuel reservoir shall have a sealing closure which shall
prevent loss or leakage of fuel from both the sealed reservoir and the sealing closure when such sealing
closure is installed in the lighter by the user in the intended manner, when tested in accordance with 6.6.
5.3.2  Refillable gas lighters shall have a pressurized fuel reservoir whose refilling valve shall be secure
enough to prevent an escape of gas exceeding 15 mg/min, when tested in accordance with 6.6.
8 © ISO 2018 – All rights reserved

ISO 9994:2018(E)
5.4  Resistance to dropping
5.4.1  Without impairing their subsequent safe operation, lighters shall be capable of withstanding
three separate (1,5 ± 0,1) m drops conducted in accordance with 6.8:
a) without fuel reservoir rupture/fragmentation, and
b) without sustained self-ignition as defined in 3.18.
In addition, for gas lighters, gas escape shall not exceed 15 mg/min.
5.4.2  Lighters that meet these requirements and that are able to be ignited in the intended manner
shall subsequently meet all the applicable requirements of 4.1 to 4.5, inclusive. Lighters that are not able
to be ignited in the intended manner do not constitute a failure.
In the event of a shield becoming detached during the drop test, it can be re-attached, if this is
practicable, and the test continued.
5.5  Resistance to elevated temperature
5.5.1  Gas lighters, and fluid lighters with a sealed compartment filled with non-absorbed fuel, shall be
capable of withstanding a temperature of 65 °C for 4 h when tested in accordance with 6.9.
5.5.2  Lighters that meet this requirement, and that are able to be ignited in the intended manner, shall
after stabilization at a temperature of (23 ± 2) °C subsequently meet all the applicable requirements of
4.1 to 4.5, inclusive. Lighters that are not able to be ignited in the intended manner do not constitute a
failure.
5.6  Resistance to internal pressure
Gas lighters shall be capable of withstanding an internal pressure of twice the vapour pressure at 55 °C
of the fuel recommended by the manufacturer, when tested in accordance with 6.10.
5.7  Burning behaviour
5.7.1  The following types of lighter shall be capable of withstanding a burning time of 5 s when held
in a position such that the top of the wick, or burner valve orifice, is at an angle 45° ± 5° below the
horizontal (see Figure 4), without evidence of any burning or distortion of components so as to cause a
hazardous condition:
— adjustable gas lighters, with the flame height set at maximum
5.7.2  The following types of lighter shall be capable of withstanding a burning time of 10 s when held
in a position such that the top of the wick, or burner valve orifice, is at an angle of 45° ± 5° below the
horizontal (see Figure 4), without evidence of any burning or distortion of components so as to cause a
hazardous condition:
— fluid lighters;
— non-a
...