ISO/ASTM 52939:2023
(Main)Additive manufacturing for construction — Qualification principles — Structural and infrastructure elements
Additive manufacturing for construction — Qualification principles — Structural and infrastructure elements
This document specifies quality assurance requirements for additive construction (AC) concerning building and construction projects in which additive manufacturing techniques are used for construction. The requirements are independent of the material(s) and process category used. This document does not apply to metals. This document specifies the criteria for additive construction processes, quality-relevant characteristics, and factors along AC system operations. It further specifies activities and sequences within an AC cell (additive construction site) and project. This document applies to all additive manufacturing technologies in building and construction (load bearing and non-load bearing), structural and infrastructure building elements for residential and commercial applications and follows an approach oriented to the process. This document does not cover environmental, health and safety aspects that apply to printing facility setup, material handling, operating of robotic equipment, and packing of equipment and/or elements for shipping but material supplier guidelines, robotic solution operating guidelines, and local and regional requirements are applicable. This document does not cover design approvals, material properties characterization and testing.
Fabrication additive pour la construction — Principes de qualification — Éléments de structure et d'infrastructure
Le présent document spécifie les exigences d'assurance qualité applicables à la construction additive (CA) pour des projets dans le domaine du bâtiment et de la construction, et impliquant des techniques de fabrication additive. Les exigences ne dépendent pas du ou des matériaux ni de la catégorie de procédé utilisés. Le présent document ne s'applique pas aux métaux. Le présent document spécifie les critères pour les procédés de construction additive, les caractéristiques significatives pour la qualité et les facteurs liés aux opérations du système de CA. Il spécifie en outre les activités et séquences mises en place au sein d'une cellule de CA (site de construction additive) et d'un projet de CA. Le présent document s'applique à l'ensemble des technologies de fabrication additive dans le domaine du bâtiment et de la construction (avec ou sans charge), concernant des éléments de construction structurels et d'infrastructure de nature résidentielle ou commerciale; il développe une approche orientée processus. Le présent document ne couvre pas les aspects relatifs à l'environnement, à la santé et à la sécurité applicables au réglage de l'installation d'impression, à la manipulation des matériaux, au fonctionnement de l'équipement robotisé, et à l'emballage de l'équipement et/ou des éléments pour livraison; cependant, les recommandations du fournisseur de matériaux, les instructions d'utilisation des solutions robotiques et les exigences locales et régionales le prescrivent. Le présent document ne traite pas de l'approbation de conception, de la caractérisation des propriétés des matériaux ni des essais.
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO/ASTM
STANDARD 52939
First edition
2023-12
Additive manufacturing for
construction — Qualification
principles — Structural and
infrastructure elements
Fabrication additive pour la construction — Principes de
qualification — Éléments de structure et d'infrastructure
Reference number
ISO/ASTM 52939:2023(E)
© ISO/ASTM International 2023
---------------------- Page: 1 ----------------------
ISO/ASTM 52939:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/ASTM International 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
ISO copyright office ASTM International
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
Phone: +41 22 749 01 11 Phone: +610 832 9634
Fax: +610 832 9635
Email: copyright@iso.org Email: khooper@astm.org
Website: www.iso.org Website: www.astm.org
Published in Switzerland
ii
© ISO/ASTM International 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/ASTM 52939:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Constructability, assessment and review. 3
4.1 General . 3
4.2 AC feasibility assessment . 4
4.3 Validation plan . 5
5 Infrastructure of the AC cell . 5
6 Qualification of the additive construction process. 8
6.1 Quality-relevant process steps within the additive construction process . 8
6.2 Data preparation . 9
6.3 Requirements for the material management . 10
6.4 System related pre-processing. 11
6.5 Built process guidance .12
6.6 System (default) post-processing . 13
6.7 Process qualification .
...
NORME ISO/ASTM
INTERNATIONALE 52939
Première édition
2023-12
Fabrication additive pour la
construction — Principes de
qualification — Éléments de structure
et d'infrastructure
Additive manufacturing for construction — Qualification principles
— Structural and infrastructure elements
Numéro de référence
ISO/ASTM 52939:2023(F)
© ISO/ASTM International 2023
---------------------- Page: 1 ----------------------
ISO/ASTM 52939:2023(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO/ASTM International 2023
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou un intranet, sans autorisation écrite soit de l’ISO à l’adresse ci-après,
soit d’un organisme membre de l’ISO dans le pays du demandeur. Aux États-Unis, les demandes doivent être adressées à ASTM
International.
ISO copyright office ASTM International
Case postale 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
CH-1214 Vernier, Genève West Conshohocken, PA 19428-2959, USA
Tél.: +41 22 749 01 11 Tél.: +610 832 9634
Fax: +610 832 9635
E-mail: copyright@iso.org E-mail: khooper@astm.org
Web: www.iso.org Web: www.astm.org
Publié en Suisse
ii
© ISO/ASTM International 2023 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO/ASTM 52939:2023(F)
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d'application .1
2 Références normatives .1
3 Termes et définitions . 1
4 Constructibilité, évaluation et examen . 4
4.1 Généralités . 4
4.2 Évaluation de la faisabilité de CA . 4
4.3 Plan de validation . 6
5 Infrastructure de la cellule de CA .6
6 Qualification du procédé de construction additive . 8
6.1 Étapes du processus de qualité dans le procédé de construction additive . 8
6.2 Préparation des données . 10
6.3 Exigences relatives à la gestion des matériaux . 11
6.4 Pré-traitement du système . 12
6.5 Conduite du procédé de fabrication . 13
6.6 Post-traitement (par défaut) du système . 15
6.7 Qualification du procédé .15
7 Assurance qualité .
...
FINAL
INTERNATIONAL ISO/ASTM
DRAFT
STANDARD FDIS
52939
ISO/TC 261
Additive manufacturing for
Secretariat: DIN
construction — Qualification
Voting begins on:
2023-09-04 principles — Structural and
infrastructure elements
Voting terminates on:
2023-10-30
Fabrication additive pour la construction — Principes de
qualification — Éléments de structure et d'infrastructure
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/ASTM FDIS 52939:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO/ASTM International 2023
---------------------- Page: 1 ----------------------
ISO/ASTM FDIS 52939:2023(E)
FINAL
INTERNATIONAL ISO/ASTM
DRAFT
STANDARD FDIS
52939
ISO/TC 261
Additive manufacturing for
Secretariat: DIN
construction — Qualification
Voting begins on:
principles — Structural and
infrastructure elements
Voting terminates on:
Fabrication additive pour la construction — Principes de
qualification — Eléments de structure et d'infrastructure
COPYRIGHT PROTECTED DOCUMENT
© ISO/ASTM International 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
ISO copyright office ASTM International
RECIPIENTS OF THIS DRAFT ARE INVITED TO
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
Phone: +41 22 749 01 11 Phone: +610 832 9634
DOCUMENTATION.
Fax: +610 832 9635
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: copyright@iso.org Email: khooper@astm.org
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/ASTM FDIS 52939:2023(E)
Website: www.iso.org Website: www.astm.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
© ISO/ASTM International 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO/ASTM International 2023
---------------------- Page: 2 ----------------------
ISO/ASTM FDIS 52939:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Constructability, assessment and review. 3
4.1 General . 3
4.2 AC feasibility assessment . 4
4.3 Validation plan . 5
...
ISO/ASTM FDIS 52939:2023(E)
Style Definition: Heading 1: Indent: Left: 0 pt, First
line: 0 pt, Tab stops: Not at 21.6 pt
ISO TC 261
Style Definition: Heading 2: Font: Bold, Tab stops: Not
Secretariat: DIN
at 18 pt
Date: 2023-06-25xx
Style Definition: Heading 3: Font: Bold
Additive manufacturing for construction — Qualification principles — Structural and
Style Definition: Heading 4: Font: Bold
infrastructure elements
Style Definition: Heading 5: Font: Bold
Fabrication additive pour la construction — Principes de qualification — Eléments de structure et
Style Definition: Heading 6: Font: Bold
d'infrastructure
Style Definition: ANNEX
Style Definition: AMEND Terms Heading: Font: Bold
Style Definition: AMEND Heading 1 Unnumbered:
Font: Bold
---------------------- Page: 1 ----------------------
ISO/ASTM FDIS 52939:2023(E)
© ISO/ASTM International 2023
Formatted: Pattern: Clear
Formatted: Pattern: Clear
All rights reserved. Unless otherwise specified, or required in the context of its implementation,
no part of this publication may be reproduced or utilized otherwise in any form or by any means,
electronic or mechanical, including photocopying, or posting on the internet or an intranet,
without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester. In the United States, such requests
should be sent to ASTM International.
ISO copyright office ASTM International
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
Phone: +41 22 749 01 11 Phone: +610 832 9634
Fax: +41 22 749 09 47 Fax: +610 832 9635
Email: copyright@iso.orgcopyright@iso.org Email: khooper@astm.org
Website: www.iso.orgwww.iso.org Website: www.astm.orgwww.astm.org
ii © ISO/ASTM International 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/ASTM FDIS 52939:2023(E)
Contents
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Constructability, Assessment and Review . 3
4.1 General . 3
4.2 AC feasibility assessment . 4
4.3 Validation plan . 5
5 Infrastructure of the AC cell . 5
6 Qualification of the additive construction process . 7
6.1 Quality-relevant process steps within the additive construction process . 7
6.2 Data preparation . 8
6.3 Requirements for the material management . 9
6.4 System related pre-processing. 10
6.5 Built Process guidance . 11
6.6 System (default) post-processing . 12
6.7 Process qualification . 12
7 Quality assurance . 13
7.1 General .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.