ISO 17531:2002

INTERNATIONAL ISO
STANDARD 17531
First edition
2002-06-15
Corrected version
2003-06-15
Photography — Processing chemicals —
Specifications for 4-(N-ethyl-N-2-
methanesulfonylaminoethyl)-2-
methylphenylenediamine sesquisulfate
monohydrate
Photographie — Produits chimiques de traitement — Spécifications pour
4-(N-éthyle-N-2-sulfonylaminoéthyle de méthane)-2-phénylénédiamine de
méthyle sesquisulfate monohydraté

Reference number
©
ISO 2002
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2002 – All rights reserved

Contents Page
Foreword . iv
Introduction. v
1 Scope. 1
2 Normative references. 1
3 General . 2
3.1 Physical properties . 2
3.2 Hazardous properties . 2
3.3 Handling and storage. 2
4 Requirements . 2
5 Reagents and glassware . 3
6 Sampling . 3
7 Test methods . 3
7.1 Assay. 3
7.2 Identity test . 4
7.3 Residue after ignition. 5
7.4 Heavy metals content . 5
7.5 Iron content. 6
7.6 Volatile matter. 6
7.7 Appearance of solution . 6
7.8 Photographic-use test . 6
Annex A (informative) Preparation of standard ammonium cerium (IV) hexanitrate solution,
c[(NH4)2Ce(NO3)6] = 0,05 mol/l (27,41 g/l). 8

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17531 was prepared by Technical Committee ISO/TC 42, Photography.
Annex A of this International Standard is for information only.
In this corrected version of ISO 17531, the following have been corrected:
 the lack of italicization of the symbol “N” in the main title and in a footnote;
 the definition of m in the equation of A.5;
 the non-italicization of the symbol for “concentration”;
 an incorrect reference to another International Standard in the Foreword;
 some minor typographical errors.
iv © ISO 2002 – All rights reserved

Introduction
This International Standard is one of a series that establishes criteria of purity for chemicals used in processing
photographic materials. General test methods and procedures cited in this International Standard are compiled in
ISO 10349-1.
This International Standard is intended for use by individuals with a working knowledge of analytical techniques,
which may not always be the case. Some of the procedures utilize caustic, toxic, or otherwise hazardous
chemicals. Safe laboratory practice for the handling of chemicals requires the use of safety glasses or goggles and,
in some cases, other protective apparel such as rubber gloves, face masks or aprons. Normal precautions for the
safe performance of any chemical procedure shall be exercised at all times, but specific details have been provided
for hazardous materials. Hazard warnings designated by a letter enclosed in angle brackets, 〈 〉, are used as a
reminder in those steps detailing handling operations and are defined in ISO10349-1. More detailed information
regarding hazards, handling and use of these chemicals may be available from the manufacturer.
This International Standard provides chemical and physical requirements for the suitability of a photographic-grade
chemical. The tests correlate with undesirable photographic effects. Purity requirements are set as low as possible
consistent with these photographic effects. These criteria are considered to be the minimum requirements
necessary to assure sufficient purity for use in photographic processing solutions; however, if the purity of a
commonly available grade of chemical exceeds photographic processing requirements and if there is no economic
penalty in its use, the purity requirements have been set to take advantage of the availability of the higher quality
material.
Every effort has been made to keep the number of requirements to a minimum. Inert impurities are limited to
amounts that will not unduly reduce the assay. All tests are performed on samples “as received” to reflect the
condition of materials furnished for use. Although the ultimate criterion for suitability of such a chemical is its
successful performance in an appropriate use test, the shorter, more economical test methods described in this
International Standard are generally adequate.
Assay procedures have been included in all cases where a satisfactory method is available. An effective assay
requirement serves not only as a safeguard of chemical purity, but also as a valuable complement to the identity
test. Identity tests have been included whenever a possibility exists that another chemical or mixture of chemicals
could pass the other tests.
All requirements listed in clause 4 are mandatory. The physical appearance of the material and any footnotes are
for general information only and are not part of the requirements.
Efforts have been made to employ tests that are capable of being run in any normally equipped laboratory and,
wherever possible, to avoid tests that require highly specialized equipment or techniques. Instrumental methods
have been specified only as alternative methods or alone in those cases where no other satisfactory method is
available.
Over the past several years, great improvements have been made in instrumentation for various analyses. Where
such techniques have equivalent or greater precision, they may be used in place of the tests described in this
International Standard. Correlation of such alternative procedures with the given method is the responsibility of the
user. In case of disagreement in results, the method called for in the specification ought to prevail. Where a
requirement states “to pass test”, however, alternative methods are not to be used.
INTERNATIONAL STANDARD ISO 17531:2002(E)

Photography — Processing chemicals — Specifications for 4-(N-
ethyl-N-2-methanesulfonylaminoethyl)-2-methylphenylenediamine
sesquisulfate monohydrate
1 Scope
This International Standard establishes criteria for the purity of photographic-grade 4-(N-ethyl-N-2-methanesulfonyl-
1) 2)
aminoethyl)-2-methylphenylenediamine sesquisulfate monohydrate and specifies the test methods to be used
to determine the purity.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 565, Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of
openings
ISO 10349-1, Photography — Photographic-grade chemicals — Test methods — Part 1: General
ISO 10349-4, Photography — Photographic-grade chemicals — Test methods — Part 4: Determination of residue
after ignition
ISO 10349-5:1992, Photography — Photographic-grade chemicals — Test methods — Part 5: Determination of
heavy metals and iron content
ISO 10349-8, Photography — Photographic-grade chemicals — Test methods — Part 8: Determination of volatile
matter
1) Sold under such trade names as CD-3 (Eastman Chemicals), FCD-03 (Fuji), and Color Developer 3 (Merck). This
information is given for the convenience of users of this International Standard and does not constitute an endorsement by ISO
of these products.
2) Other names:
N-ethyl-N-(ß-methylsulfonamidoethyl)-3-methyl-p-phenylenediamine sesquisulfate monohydrate
4-amino-N-ethyl-N-(ß-methanesulfonamidoethyl)-m-toluidine sesquisulfate monohydrate
4-amino-N-(ß-methanesulfonamidoethyl)-3-methylaniline sesquisulfate monohydrate
N-(4-amino-N-ethyl-m-toluidine)-ethylmethanesulfonamide sesquisulfate monohydrate
3 General
3.1 Physical properties
4-(N-ethyl-N-2-methanesulfonylaminoethyl)-2-methylphenylenediamine sesquisulfate monohydrate
. .
(C H N O S 3/2 H SO H O) exists in the form of white to medium-tan or light-pink coloured granules or
12 21 3 2 2 4 2
powder. It has a relative molecular mass of 436,52.
3.2 Hazardous properties
4-(
...