ISO 8468:2007
(Main)Ships and marine technology — Ship's bridge layout and associated equipment — Requirements and guidelines
Ships and marine technology — Ship's bridge layout and associated equipment — Requirements and guidelines
ISO 8468:2007 specifies the functional requirements for bridge configuration, bridge arrangement, bridge workstations and bridge environment. Guidelines have been drawn up for the methods and solutions to meet the functional requirements. The requirements in ISO 8468:2007 apply to all bridge functions. The purpose of ISO 8468:2007 is to assist the operator(s) and pilot by providing a workplace that is conducive to safe and effective operation. It also aims to specify bridge requirements, which will secure safe and efficient operation of the ship berth-to-berth regardless of the watchkeeping arrangement in place at a particular time. ISO 8468:2007 should be used in support of the aims in SOLAS Chapter V Regulation 15. Requirements and guidance on the human element aspects of the bridge system (e.g. training, procedures) are not given. The main use of ISO 8468:2007 will be for designing ships' bridges. ISO 8468:2007 will also be useful to specifiers and procurers of ships and bridge equipment, operators, and owners for ensuring that changes made to the bridge through the life of a ship continue to conform to these requirements. ISO 8468:2007 is applicable to seagoing ships. Annex A of ISO 8468:2007 applies to high speed craft.
Navires et technologie maritime — Aménagement de la passerelle d'un navire et disposition de ses équipements annexes — Exigences et directives
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 8468
Third edition
2007-07-15
Ships and marine technology — Ship's
bridge layout and associated
equipment — Requirements and
guidelines
Navires et technologie maritime — Aménagement de la passerelle d'un
navire et disposition de ses équipements annexes — Exigences et
directives
Reference number
ISO 8468:2007(E)
©
ISO 2007
---------------------- Page: 1 ----------------------
ISO 8468:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 8468:2007(E)
Contents Page
Foreword. v
Introduction . vi
1 Scope . 1
2 Normative references . 2
3 Terms, definitions and abbreviations. 2
3.1 Terms and definitions. 2
3.2 Abbreviations . 7
4 Bridge configuration. 8
4.1 General. 8
4.2 Field of vision. 8
4.2.1 General. 8
4.2.2 Primary conning position . 8
4.2.3 Navigation and manoeuvring workstation . 9
4.2.4 Monitoring and secondary navigation workstation . 13
4.2.5 Docking (bridge wings) workstation. 13
4.2.6 Manual steering (helmsman’s) workstation. 14
4.3 Windows . 14
4.4 Sound reception system . 15
5 Bridge functions and tasks and their relations to workstations . 15
5.1 General.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.