ISO 10122:2014

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 10122
ISO/TC 61/SC 13
Reinforcement materials — Tubular
Secretariat: JISC
braided sleeves — Basis for a
Voting begins on:
2014-05-20 specification
Voting terminates on:
Produits de renfort — Gaines tressées — Base de spécification
2014-07-20
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/FDIS 10122:2014(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2014

ISO/FDIS 10122:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

ISO/FDIS 10122:2014(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Description and designation . 2
4.1 Technical description of tubular braided sleeves . 2
4.2 Designation . 2
5 Characteristics . 3
5.1 General . 3
5.2 Characteristics to be specified . 3
5.3 Defects . 4
6 Sampling and conditioning of specimens . 4
6.1 Sampling . 4
6.2 Conditioning of specimens . 4
7 Test methods . 5
7.1 Thickness . 5
7.2 Diameter, braid angle, and mass per metre length . 5
8 Packaging and ordering . 7
8.1 Packaging . 7
8.2 Ordering data . 7
9 Storage . 7
ISO/FDIS 10122:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 13, Composites
and reinforcement fibres.
This second edition cancels and replaces the first edition (ISO 10122:1995), which has been technically
revised.
iv © ISO 2014 – All rights reserved

FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 10122:2014(E)
Reinforcement materials — Tubular braided sleeves —
Basis for a specification
1 Scope
This International Standard provides a basis for specifications applicable to tubular braided sleeves
used as reinforcements in plastics. Its deals with tubular sleeves braided from all types of yarn or roving.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 1887, Textile glass — Determination of combustible-matter content
ISO 1889, Reinforcement yarns — Determination of linear density
ISO 2797, Textile glass — Rovings — Basis for a specification
ISO 3598, Textile glass — Yarns — Basis for a specification
ISO 4603, Textile glass — Woven fabrics — Determination of thickness
ISO 8516, Textile glass — Textured yarns — Basis for a specification
ISO 10548, Carbon fibre — Determination of size content
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
tubular braided sleeve
sleeve made by interlacing (braiding or plaiting) four or more yarns or rovings in such a way that they
cross one another and are laid together in a helical formation
3.2
braiding
method of interlacing yarns or rovings
3.3
construction
structure of a sleeve, depending closely upon the type of machine used and the number of yarns or
rovings per carrier
3.4
carrier
braiding-machine part on which the yarns or rovings ar
...