ISO 4141-3:2006

INTERNATIONAL ISO
STANDARD 4141-3
Second edition
2006-07-01

Road vehicles — Multi-core connecting
cables —
Part 3:
Construction, dimensions and marking of
unscreened sheathed low-voltage cables
Véhicules routiers — Câbles de raccordement multiconducteurs —
Partie 3: Construction, dimensions et marquage des câbles basse
tension gainés non blindés




Reference number
ISO 4141-3:2006(E)
©
ISO 2006

---------------------- Page: 1 ----------------------
ISO 4141-3:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2006 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 4141-3:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4141-3 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 3, Electrical
and electronic equipment.
This second edition cancels and replaces the first edition (ISO 4141-3:1998), which has been technically
revised. It also incorporates the Technical Corrigendum ISO 4141-3:1998/Cor.1:1999.
ISO 4141 consists of the following parts, under the general title Road vehicles — Multi-core connecting
cables:
⎯ Part 1: Test methods and requirements for basic performance sheathed cables
⎯ Part 2: Test methods and requirements for high performance sheathed cables
⎯ Part 3: Construction, dimensions and marking of unscreened sheathed low-voltage cables
⎯ Part 4: Articulation test method and requirements for coiled cable assemblies
The following part is under preparation:
⎯ Part 4: Test methods and requirements for coiled cable assemblies [Revision of ISO 4141-4:2001]

© ISO 2006 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 4141-3:2006(E)

Road vehicles — Multi-core connecting cables —
Part 3:
Construction, dimensions and marking of unscreened sheathed
low-voltage cables
1 Scope
This part of ISO 4141 specifies the construction, dimensions and marking of unscreened sheathed low-voltage
multi-core cables for the connection of towing and towed vehicles, suitable for the temperature range
− 40 °C to + 85 °C.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1185, Road vehicles — Connectors for the electrical connection of towing and towed vehicles — 7-pole
connector type 24 N (normal) for vehicles with 24 V nominal supply voltage
ISO 1724, Road vehicles — Connectors for the electrical connection of towing and towed vehicles — 7-pole
connector type 12 N (normal) for vehicles with 12 V nominal supply voltage
ISO 3731, Road vehicles — Connectors for the electrical connection of towing and towed vehicles — 7-pole
connector type 24 S (supplementary) for vehicles with 24 V nominal supply voltage
ISO 3732, Road vehicles — Connectors for the electrical connection of towing and towed vehicles — 7-pole
connector type 12 S (supplementary) for vehicles with 12 V nominal supply voltage
ISO 4141-1, Road vehicles — Multi-core connecting cables — Part 1: Test methods and requirements for
basic performance sheathed cables
ISO 4141-2, Road vehicles — Multi-core connecting cables — Part 2: Test methods and requirements for high
performance sheathed cables
ISO 7638-1, Road vehicles — Connectors for the electrical connection of towing and towed vehicles — Part 1:
Connectors for braking systems and running gear of vehicles with 24 V nominal supply voltage
ISO 7638-2, Road vehicles — Connectors for the electrical connection of towing and towed vehicles — Part 2:
Connectors for braking syste
...