EN 61340-5-3:2010

SLOVENSKI STANDARD
01-september-2010
(OHNWURVWDWLNDGHO=DãþLWDHOHNWURQVNLKQDSUDYSUHGHOHNWURVWDWLþQLPLSRMDYL
/DVWQRVWLLQNODVLILNDFLMD]DKWHY]DHPEDODåRQDSUDYNLVRREþXWOMLYH]D
HOHNWURVWDWLþQHUD]HOHNWULWYH,(&
Electrostatics - Part 5-3: Protection of electronic devices from electrostatic phenomena -
Properties and requirements classifications for packaging intended for electrostatic
discharge sensitive devices (IEC 61340-5-3:2010)
Elektrostatik - Teil 5-3: Schutz von elektronischen Bauelementen gegen elektrostatische
Phänomene - Eigenschaften und Anforderungen für die Klassifizierung von
Verpackungen welche für Bauelemente verwendet werden, die gegen elektrostatische
Entladungen empfindlich sind (IEC 61340-5-3:2010)
Electrostatique - Partie 5-3: Protection des dispositifs électroniques contre les
phénomènes électrostatiques - Classifications des propriétés et des exigences relatives
à l'emballage destiné aux dispositifs sensibles aux décharges électrostatiques (CEI
61340-5-3:2010)
Ta slovenski standard je istoveten z: EN 61340-5-3:2010
ICS:
17.220.99 Drugi standardi v zvezi z Other standards related to
elektriko in magnetizmom electricity and magnetism
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61340-5-3
NORME EUROPÉENNE
May 2010
EUROPÄISCHE NORM
ICS 17.220.99; 29.020
English version
Electrostatics -
Part 5-3: Protection of electronic devices from electrostatic phenomena -
Properties and requirements classifications for packaging intended
for electrostatic discharge sensitive devices
(IEC 61340-5-3:2010)
Electrostatique -  Elektrostatik -
Partie 5-3: Protection des dispositifs Teil 5-3: Schutz von elektronischen
électroniques contre les phénomènes Bauelementen gegen elektrostatische
électrostatiques - Phänomene -
Classifications des propriétés Eigenschaften und Anforderungen
et des exigences relatives à l'emballage für die Klassifizierung von Verpackungen
destiné aux dispositifs sensibles welche für Bauelemente verwendet
aux décharges électrostatiques werden, die gegen elektrostatische
(CEI 61340-5-3:2010) Entladungen empfindlich sind
(IEC 61340-5-3:2010)
This European Standard was approved by CENELEC on 2010-05-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61340-5-3:2010 E
Foreword
The text of document 101/295/FDIS, future edition 1 of IEC 61340-5-3, prepared by IEC TC 101,
Electrostatics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 61340-5-3 on 2010-05-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2011-02-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2013-05-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61340-5-3:2010 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
[2] IEC 61340-5-1 NOTE  Harmonized as EN 61340-5-1.
[3] IEC/TR 61340-5-2 NOTE  Harmonized as CLC/TR 61340-5-2.
[4] IEC 61340-3-1 NOTE  Harmonized as EN 61340-3-1.
[5] IEC 61340-3-2 NOTE  Harmonized as EN 61340-3-2.
__________
- 3 - EN 61340-5-3:2010
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 61340-2-3 - Electrostatics - EN 61340-2-3 -
Part 2-3: Methods of test for determining the
resistance and resistivity of solid planar
materials used to avoid electrostatic charge
accumulation
IEC 61340-4-8 - Electrostatics - - -
Part 4-8: Standard test methods for specific
applications - Discharge shielding - Bags

ANSI/ESD STM 11.13 - Two-point resistance measurement - -

IEC 61340-5-3 ®
Edition 1.0 2010-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electrostatics –
Part 5-3: Protection of electronic devices from electrostatic phenomena –
Properties and requirements classification for packaging intended for
electrostatic discharge sensitive devices

Electrostatique –
Partie 5-3: Protection des dispositifs électroniques contre les phénomènes
électrostatiques – Classification des propriétés et des exigences relatives à
l'emballage destiné aux dispositifs sensibles aux décharges électrostatiques

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
R
CODE PRIX
ICS 17.220.99; 29.020 ISBN 2-8318-1383-7
– 2 – 61340-5-3 © IEC:2010
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 Terms and definitions .6
4 Tailoring .7
5 Packaging application requirement .7
5.1 General .7
5.2 Inside an EPA .7
5.3 Outside an EPA.8
6 Classification of ESD packaging material properties .8
6.1 General .8
6.2 Material resistance properties .8
6.2.1 Resistance of conductive materials.8
6.2.2 Resistance of electrostatic field shielding materials .8
6.2.3 Resistance of dissipative materials.9
6.2.4 Resistance of insulative materials.9
6.3 Material electrostatic shielding properties.9
6.3.1 Electrostatic discharge shielding .9
6.3.2 Electrostatic field shielding .9
7 Technical requirements for ESD protective packaging .9
7.1 Packaging and material properties .9
7.2 Packaging marking .9
7.2.1 Classification symbol .9
7.2.2 Packaging classification .9
7.2.3 Traceability.9
Annex A (informative) ESD packaging material guidance .13
Annex B (informative) Device damage .17
Bibliography.18

Figure 1 – Example of packaging label.10
Figure 2 – Examples of EPA configurations .12
Figure A.1 – Application of ESD protective packaging.15

Table 1 – Test methods for electrostatic protective packaging .
Table 2 – Test methods and requirements for electrostatic discharge shielding
packaging .11
Table A.1 – Packaging characteristics for environmental consideration.13
Table A.2 – Examples for qualification and verification of packaging.16

61340-5-3 © IEC:2010 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTROSTATICS –
Part 5-3: Protection of electronic devices from electrostatic phenomena –
Properties and requirements classification for packaging intended for
electrostatic discharge sensitive devices

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature
...