EN 61169-1:1994/A2:1997

SLOVENSKI STANDARD
01-april-1998
Radio-frequency connectors - Part 1: Generic specification - General requirements
and measuring methods - Amendment A2 (IEC 61169-1:1992/A2:1997)
Radio-frequency connectors -- Part 1: Generic specification - General requirements and
measuring methods
Hochfrequenz-Steckverbinder -- Teil 1: Fachgrundspezifikation - Allgemeine
Anforderungen und Meßverfahren
Connecteurs pour fréquences radioélectriques -- Partie 1: Spécification générique -
Prescriptions générales et méthodes de mesure
Ta slovenski standard je istoveten z: EN 61169-1:1994/A2:1997
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML R.F. connectors
5)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

NORME
CEI
INTERNATIONALE
IEC
61169-1
INTERNATIONAL
QC 220000
STANDARD
AMENDEMENT 2
AMENDMENT 2
1997-04
Amendement 2
Connecteurs pour fréquences radioélectriques –
Partie 1:
Spécification générique –
Prescriptions générales et méthodes de mesure
Amendment 2
Radio-frequency connectors –
Part 1:
Generic specification –
General requirements and measuring methods
 IEC 1997 Droits de reproduction réservés  Copyright - all rights reserved
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
PRICE CODE E
International Electrotechnical Commission
Pour prix, voir catalogue en vigueur
For price, see current catalogue

61169-1 Amend. 2 © IEC:1997 – 3 –
FOREWORD
This amendment has been prepared by the subcommittee 46D: RF connectors, of IEC
technical committee 46: Cables, wires, waveguides, RF connectors, and accessories for
communication and signalling.
The text of this amendment is based on the following documents:
FDIS Report on voting
46D/279/FDIS 46D/296/RVD
Full information on the voting for the approval of this amendment can be found in the report on
voting indicated in the above table.
________
Page 151
Add, after subclause 10.3.2.3, the following new subclause
10.3.3 Test schedules and inspection requirements for alternative fixed-quantity sample procedures
Table 1 – Lot-by-lot procedure – Acceptance tests: groups A1 and B1
Test
Assessment level M (higher) Assessment level H (lower)
method
of IEC
61169-1
Test AQL Period Test AQL Period
QC 220000
IL IL
required % required %
Subclause
Group A1
Visual inspection
9.1.2 a 11 1,0 a S3 1,5
Group B1
Outline dimensions
9.1.3.1 a S4 0,40 a S3 0,40
Mechanical compatibility
9.1.3.3 a 11 1,0 a S3 1,5
Engagement and separation
9.3.6 a S4 0,40 a S3 1,5
Lot Lot
Gauge retention force
9.3.4 ia 11 1,0 ia S3 1,5
(resilient contacts)
by by
Scaling, non-hermetic
9.4.5.1 ia 11 0,65 ia S3 1,0
Scaling, hermetic
9.4.5.2 ia 11 0,015 ia S3 0,025
lot lot
Voltage proof
9.2.6 a S4 0,40 a 11 4,0
d)
Solderability piece-parts
9.3.2.1.1 ia S4 0,40 ia S3 4,0
Insulation resistance
9.2.5 a S4 0,40 a S3 4,0
Effectiveness of safety wire locking
TBD ia S4 0,40 ia S3 4,0
d)
holes; piece-parts
a applicable
ia test required (if technically applicable)
IL inspection
...