EN 61169-18:2011

SLOVENSKI STANDARD
01-maj-2011
5DGLRIUHNYHQþQLNRQHNWRUMLGHO3RGURþQDVSHFLILNDFLMD5DGLRIUHNYHQþQL
NRDNVLDOQLNRQHNWRUMLYUVWH660$,(&
Radio-frequency connectors - Part 18: Sectional specification - Radio frequency coaxial
connectors of type SSMA (IEC 61169-18:2011)
Hochfrequenz-Steckverbinder - Teil 18: Rahmenspezifikation - Hochfrequenz-Koaxial-
Steckverbinder des Typs SSMA (IEC 61169-18:2011)
Connecteurs pour fréquences radioélectriques - Partie 18: Spécification intermédiaire -
Connecteurs coaxiaux pour fréquences radioélectriques de type SSMA (CEI 61169-
18:2011)
Ta slovenski standard je istoveten z: EN 61169-18:2011
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML R.F. connectors
5)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61169-18
NORME EUROPÉENNE
March 2011
EUROPÄISCHE NORM
ICS 33.120.30
English version
Radio-frequency connectors -
Part 18: Sectional specification -
Radio frequency coaxial connectors of type SSMA
(IEC 61169-18:2011)
Connecteurs pour fréquences Hochfrequenz-Steckverbinder -
radioélectriques - Teil 18: Rahmenspezifikation -
Partie 18: Spécification intermédiaire - Hochfrequenz-Koaxial-Steckverbinder des
Connecteurs coaxiaux pour fréquences Typs SSMA
radioélectriques de type SSMA (IEC 61169-18:2011)
(CEI 61169-18:2011)
This European Standard was approved by CENELEC on 2011-03-03. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61169-18:2011 E
Foreword
The text of document 46F/136/CDV, future edition 1 of IEC 61169-18, prepared by SC 46F, R.F. and
microwave passive components, of IEC TC 46, Cables, wires, waveguides, R.F. connectors, R.F. and
microwave passive components and accessories, was submitted to the IEC-CENELEC parallel vote and
was approved by CENELEC as EN 61169-18 on 2011-03-03.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-12-03
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2014-03-03
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61169-18:2011 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61169-18:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 61169-1 1992 Radio-frequency connectors - EN 61169-1 1994
A1 1996 Part 1: Generic specification - General A1 1996
A2 1997 requirements and measuring methods A2 1997

IEC 61169-18 ®
Edition 1.0 2011-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio-frequency connectors –
Part 18: Sectional specification – Radio frequency coaxial connectors of type
SSMA
Connecteurs pour fréquences radioélectriques –
Partie 18: Spécification intermédiaire – Connecteurs coaxiaux pour fréquences
radioélectriques de type SSMA
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX T
ICS 33.120.30 ISBN 978-2-88912-319-3
– 2 – 61169-18  IEC:2011
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Mating face and gauge information . 6
3.1 Dimensions - High performance connectors – Grade 1 . 6
3.1.1 Connector with pin-centre contact . 7
3.1.2 Connector with socket-centre contact . 8
3.2 Gauges . 9
3.2.1 Gauge pins for socket-centre contact . 9
3.2.2 Test procedure . 9
3.3 Dimensions - standard test connectors – Grade 0 . 10
3.3.1 Connector with pin-centre contact . 10
3.3.2 Connector with socket-centre contact . 11
4 Quality assessment procedure . 12
4.1 General . 12
4.2 Standard ratings and characteristics (see Clause 6 of IEC 61169-1) . 12
4.3 Test schedule and inspection requirements – Acceptance tests . 15
4.3.1 Acceptance tests . 15
4.3.2 Periodic tests . 15
4.4 Procedures . 18
4.4.1 Quality conformance inspection . 18
4.4.2 Qualification approval and its maintenance . 18
5 Instructions for preparation of detail specifications . 18
5.1 General . 18
5.2 Identification of the component . 18
5.3 Performance . 19
5.4 Marking, ordering information and related matters . 19
5.5 Selection of tests, test conditions and severities . 19
5.6 Blank detail specification pro-forma for type SSMA connector . 20

Figure 1 – Connector with pin-centre contact (for dimensions and notes, see Table 1) . 7
Figure 2 – Connector with socket-centre contact (for dimensions and notes, see
Table 2) . 8
Figure 3 – Gauge pins for socket-centre contact (for dimensions and notes, see
Table 3) . 9
Figure 4 – Connector with pin-centre contact (for dimensions and notes, see Table 4) . 10
Figure 5 – Connector with socket-centre contact (for dimensions and notes, see
Table 5) . 11

61169-18  IEC:2011 – 3 –
Table 1 – Dimensions of connector with pin-centre contact . 7
Table 2 – Dimensions of connector with socket-centre contact . 8
Table 3 – Dimensions of gauge pins for socket-centre contact . 9
Table 4 – Dimensions of connector with pin-centre contact . 10
Table 5 – Dimensions of connector with socket-centre contact . 12
Table 6 – Rating and characteristics . 13
Table 7 – Acceptance tests . 15
Table 8 – Periodic tests . 16

– 4 – 61169-18  IEC:2011
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
RADIO-FREQUENCY CONNECTORS –
Part 18: Sectional specification –
Radio frequency coaxial connectors of type SSMA

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61169-18 has been prepared by subcommittee 46F: R
...