EN 61338-4:2005

SLOVENSKI SIST EN 61338-4:2005

STANDARD
december 2005
Dielektrični resonatorji valovodnega tipa – 4. del: Področna specifikacija (IEC
61338-4:2005)
Waveguide type dielectric resonators – Part 4: Sectional specification (IEC 61338-
4:2005)
ICS 31.140; 33.120.10 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 61338-4
NORME EUROPÉENNE
EUROPÄISCHE NORM May 2005
ICS 31.140
English version
Waveguide type dielectric resonators
Part 4: Sectional specification
(IEC 61338-4:2005)
Résonateurs diélectriques  Dielektrische Resonatoren
à modes guidés vom Wellenleitertyp
Partie 4: Spécification intermédiaire Teil 4: Rahmenspezifikation
(CEI 61338-4:2005) (IEC 61338-4:2005)

This European Standard was approved by CENELEC on 2005-04-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 61338-4:2005 E
Foreword
The text of document 49/702/FDIS, future edition 1 of IEC 61338-4, prepared by IEC TC 49,
Piezoelectric and dielectric devices for frequency control and selection, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 61338-4 on 2005-04-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2006-01-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-04-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61338-4:2005 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61338-4:2005
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2)
IEC 61338-1 - Waveguide type dielectric resonators EN 61338-1 2005
Part 1: Generic specification
1)
IEC QC 001002-3 - IEC Quality Assessment System for - -
Electronic Components (IECQ) - Rules of
Procedure
Part 3: Approval procedures
1)
IEC QC 001005 - Register of films, products and services - -
approved under the IECQ system,
including ISO 9000
1)
Undated reference.
2)
Valid edition at date of issue.

INTERNATIONAL IEC
STANDARD 61338-4
First edition
2005-03
Waveguide type dielectric resonators –
Part 4:
Sectional specification
 IEC 2005  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale
R
International Electrotechnical Commission
Международная Электротехническая Комиссия
For price, see current catalogue

– 2 – 61338-4  IEC:2005(E)
CONTENTS
FOREWORD .3

1 General.5
1.1 Scope .5
1.2 Normative references .5
2 Preferred ratings and guidance on detail specifications.5
2.1 Preferred ratings and characteristics .5
2.2 Information to be prescribed in detail specifications .5
3 Capability approval.6
3.1 Eligibility for capability approval.6
3.2 Structural similarity.6
3.3 Procedures for capability approval .6
3.4 Description of capability .7
3.5 Capability Qualifying Components (CQCs).7
3.6 Inspection requirements for CQCs .8
3.7 Programme for capability approval.8
3.8 Capability approval report.9
3.9 Abstract of description of capability .9
3.10 Modifications likely to affect the capability approval .9
3.11 Initial capability approval .9
3.12 Maintenance of capability approval .13
3.13 Rework and repair work.14
3.14 Quality conformance inspection .14
3.15 Screening procedures.15
4 Test and measurement procedures.15

Annex A (normative) Example layout of an abstract of description of capability.16
Annex B (normative) Layout of the front page of a CQC specification for process control.17
Annex C (normative) Layout of the front page of a CQC specification to demonstrate
boundary or limit.18

Figure 1 – Selection of CQCs.10
Figure 2 – Test plan for sintering process CQCs .11
Figure 3 – Test plan for deposition of electrode material CQCs .11
Figure 4 – Test plan for resonator performance CQCs.12
Figure 5 – Test plan for climatic performance CQCs.12
Figure 6 – Test plan for humidity CQCs.12
Figure 7 – Test plan for ageing CQCs .13
Figure 8 – Test plan for mechanical endurance CQCs .13
Figure 9 – Test plan for resistance to soldering heat CQCs .13

Table 1 – Periodic tests for maintenance of capability approval .14

61338-4  IEC:2005(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
WAVEGUIDE TYPE DIELECTRIC RESONATORS –

Part 4: Sectional specification

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61338-4 has been prepared by IEC technical committee 49:
Piezoelectric and dielectric devices for frequency control and selection.
The text of this standard is based on the following documents:
FDIS Report on voting
49/702/FDIS 49/716/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

– 4 – 61338-4  IEC:2005(E)
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
IEC 61338 consists of the following parts, under the general title: Waveguide type dielectric
resonators:
Part 1: Generic specification
Part 1-3: General information and test conditions – Measurement method of complex relative
permittivity for dielectric resonator materials at microwave frequency
Part 2: Guidelines for oscillator and filter applications
Part 4: Sectional specification (this publication)
Part 4-1: Blank detail specification
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

61338-4  IEC:2005(E) – 5 –
WAVEGUIDE TYPE DIELECTRIC RESONATORS –

Part 4: Sectional specification

1 General
1.1 Scope
This sectional specification applies to waveguide type dielectric resonators as custom built
products or as standard catalogue items whose quality is assessed on the basis of capability
approval.
It prescribes the preferred ratings and characteristics wit
...