Electric motor-operated tools - Dust measurement procedure - Part 1: General requirements

This European Standard specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This European Standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected. This part of EN 50632 sets general requirements for all affected kinds of tools.

Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 1: Allgemeine Anforderungen

Outils électriques à moteur - Procédure de mesure de la poussière - Partie 1: Exigences générales

Elektromotorna orodja - Postopek meritve prahu - 1. del: Splošne zahteve - Dopolnilo A2

Ta evropski standard določa splošne zahteve za meritve prahu elektromotornih orodij, ki se napajajo iz omrežja ali baterij. Ta evropski standard velja za tista orodja, pri katerih se pričakuje nabiranje prahu (na primer mineralnega prahu, ki vsebuje kremenico, ali lesnega prahu), ne glede na to, ali so opremljeni z enoto za izločevanje prahu ali ne.

General Information

Status
Published
Publication Date
23-Dec-2021
Current Stage
6060 - Document made available - Publishing
Start Date
24-Dec-2021
Due Date
09-Aug-2022
Completion Date
24-Dec-2021

Relations

Buy Standard

Amendment
EN 50632-1:2015/A2:2022
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-marec-2022
Elektromotorna orodja - Postopek meritve prahu - 1. del: Splošne zahteve -
Dopolnilo A2
Electric motor-operated tools - Dust measurement procedure - Part 1: General
requirements
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 1: Allgemeine
Anforderungen
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 1: Exigences
générales
Ta slovenski standard je istoveten z: EN 50632-1:2015/A2:2021
ICS:
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 50632-1:2015/A2

NORME EUROPÉENNE
EUROPÄISCHE NORM December 2021
ICS 25.140.20
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 1: General requirements
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 1: Exigences générales Teil 1: Allgemeine Anforderungen
This amendment A2 modifies the European Standard EN 50632-1:2015; it was approved by CENELEC on 2021-12-07. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-1:2015/A2:2012 E

Contents Page
European foreword . 3
1 Modification to 4.2, “Test room and equipment” . 4
2 Modification to 4.3, “Operating conditions” . 4
3 Addition of Figures 1 and 2 . 5

European foreword
This document (EN 50632-1:2015/A2:2021) has been prepared by CLC/TC 116 “Safety and environmental
aspects of motor-operated electric tools”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2022-12-07
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2024-12-07
conflicting with this document have to be
withdrawn
This amendment was developed to include improvements and clarifications suggested by practical tests.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A complete
listing of these bodies can be found
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.