EN IEC 60730-2-9:2019/A2:2020
(Amendment)Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls
Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls
2019-03-19: to contact PM before proceeding with any assessment request.
Automatische elektrische Regel- und Steuergeräte - Teil 2-9: Besondere Anforderungen an temperaturabhängige Regel- und Steuergeräte
Dispositifs de commande électrique automatiques - Partie 2-9: Exigences particulières pour les dispositifs de commande thermosensibles
Avtomatske električne krmilne naprave - 2-9. del: Posebne zahteve za temperaturne regulatorje - Dopolnilo A2
General Information
Relations
Overview
EN IEC 60730-2-9:2019/A2:2020 is a CENELEC-adopted amendment to the European/IEC standard for automatic electrical controls that specifies particular requirements for temperature sensing controls. Approved 14 May 2020, this Amendment A2 modifies the EN IEC 60730-2-9:2019 text and applies to temperature-dependent control devices used in household and similar applications (ICS 97.120). It clarifies and adds test requirements for actions classified as Type 1.H/2.H and Type 1.J/2.J and provides procedural details for verification of reset behaviour and contact operations.
Key topics and technical requirements
- Scope: Particular requirements for temperature sensing controls within the IEC 60730 series (automatic electrical controls).
- Amendment status: EN IEC 60730-2-9:2019 modified by A2 (2020); national implementation deadline noted in the European foreword.
- Test procedures (added or clarified by A2):
- Reset mechanism tests: For Type 1.H/2.H and Type 1.J/2.J actions, the reset mechanism may be held in the reset position for defined sequences of tests.
- Continuity/ contact observation: Use a low-energy circuit (maximum 0.05 A) to observe contact continuity or separation.
- Environmental conditioning: Install the sensing element or whole control in an air-circulating chamber or oil bath; position a thermocouple adjacent to the control under test to determine bath/chamber temperature.
- Temperature staging: Hold the chamber at approximately 10 K below the set point until stable, then raise temperature at a rate of no more than 0.5 K/min until contact operation is observed.
- Additional limits: For some tests (Type 1.J/2.J) temperature is raised until 10 K over the operation temperature; post-operation cooling may require verification down to +0 °C or −35 °C as declared (see item 103 of Table 1 / SOD).
- Measurement and verification methods are precisely defined to ensure repeatable, safe evaluation of automatic non-resetting and automatic resetting behaviour.
Applications and users
Who uses this standard:
- Manufacturers of temperature sensing controls (thermostats, temperature switches, safety controls).
- Test laboratories and conformity assessment bodies performing type and production testing.
- Design and compliance engineers in HVAC, household appliances, refrigeration and other temperature-controlled products.
- Product managers and regulatory teams preparing technical documentation for CE/CENELEC compliance.
Practical value:
- Ensures consistent, reproducible testing for reset and contact behaviour under controlled thermal conditions.
- Helps demonstrate product safety, reliability and conformity with the IEC 60730 family requirements.
Related standards
- IEC 60730 series (automatic electrical controls) - base standard family for control device safety and performance.
- EN IEC 60730-2-9:2019 (base European adoption) - Amendment A2 updates this publication.
Keywords: EN IEC 60730-2-9:2019/A2:2020, automatic electrical controls, temperature sensing controls, temperature control testing, reset mechanism test, Type 1.H, Type 1.J, IEC 60730 amendment A2, CENELEC, product compliance, HVAC, household appliances.
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60730-2-9:2019/A2:2020
01-oktober-2020
Avtomatske električne krmilne naprave - 2-9. del: Posebne zahteve za
temperaturne regulatorje - Dopolnilo A2
Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing
control
Ta slovenski standard je istoveten z: EN IEC 60730-2-9:2019/A2:2020
ICS:
97.120 Avtomatske krmilne naprave Automatic controls for
za dom household use
SIST EN 60730-2-9:2019/A2:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN 60730-2-9:2019/A2:2020
SIST EN 60730-2-9:2019/A2:2020
EUROPEAN STANDARD EN IEC 60730-2-9:2019/A2
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2020
ICS 97.120
English Version
Automatic electrical controls - Part 2-9: Particular requirements
for temperature sensing controls
(IEC 60730-2-9:2015/A2:2020)
Dispositifs de commande électrique automatiques - Partie Automatische elektrische Regel- und Steuergeräte - Teil 2-
2-9: Exigences particulières pour les dispositifs de 9: Besondere Anforderungen an temperaturabhängige
commande thermosensibles Regel- und Steuergeräte
(IEC 60730-2-9:2015/A2:2020) (IEC 60730-2-9:2015/A2:2020)
This amendment A2 modifies the European Standard EN IEC 60730-2-9:2019; it was approved by CENELEC on 2020-05-14. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60730-2-9:2019/A2:2020 E
SIST EN 60730-2-9:2019/A2:2020
European foreword
The text of document 72/1225/FDIS, future IEC 60730-2-9/A2, prepared by IEC/TC 72 "Automatic
electrical controls" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-02-14
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-05-14
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association.
Endorsement notice
The text of the International Standard IEC 60730-2-9:2015/A2:2020 was approved by CENELEC as a
European Standard without any modification.
SIST EN 60730-2-9:2019/A2:2020
IEC 60730-2-9 ®
Edition 4.0 2020-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 2
AM ENDEMENT 2
Automatic electrical controls –
Part 2-9: Particular requirements for temperature sensing controls
Dispositifs de commande électrique automatiques –
Partie 2-9: Exigences particulières pour les dispositifs de commande
thermosensibles
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 97.120 ISBN 978-2-8322-8066-9
SIST EN 60730-2-9:2019/A2:2020
– 2 – IEC 60730-2-9:2015/AMD2:2020
© IEC 2020
FOREWORD
This amendment has been prepared by IEC technical committee 72: Automatic electrical
controls.
The text of this amendment is based on the following documents:
FDIS Report on voting
72/1225/FDIS 72/1236/RVD
Full information on the voting for the approval of this amendment can be found in the report on
voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC website under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
...
SLOVENSKI STANDARD
01-oktober-2020
Avtomatske električne krmilne naprave - 2-9. del: Posebne zahteve za
temperaturne regulatorje - Dopolnilo A2
Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing
control
Ta slovenski standard je istoveten z: EN IEC 60730-2-9:2019/A2:2020
ICS:
97.120 Avtomatske krmilne naprave Automatic controls for
za dom household use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60730-2-9:2019/A2
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2020
ICS 97.120
English Version
Automatic electrical controls - Part 2-9: Particular requirements
for temperature sensing controls
(IEC 60730-2-9:2015/A2:2020)
Dispositifs de commande électrique automatiques - Partie Automatische elektrische Regel- und Steuergeräte - Teil 2-
2-9: Exigences particulières pour les dispositifs de 9: Besondere Anforderungen an temperaturabhängige
commande thermosensibles Regel- und Steuergeräte
(IEC 60730-2-9:2015/A2:2020) (IEC 60730-2-9:2015/A2:2020)
This amendment A2 modifies the European Standard EN IEC 60730-2-9:2019; it was approved by CENELEC on 2020-05-14. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60730-2-9:2019/A2:2020 E
European foreword
The text of document 72/1225/FDIS, future IEC 60730-2-9/A2, prepared by IEC/TC 72 "Automatic
electrical controls" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-02-14
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-05-14
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association.
Endorsement notice
The text of the International Standard IEC 60730-2-9:2015/A2:2020 was approved by CENELEC as a
European Standard without any modification.
IEC 60730-2-9 ®
Edition 4.0 2020-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 2
AM ENDEMENT 2
Automatic electrical controls –
Part 2-9: Particular requirements for temperature sensing controls
Dispositifs de commande électrique automatiques –
Partie 2-9: Exigences particulières pour les dispositifs de commande
thermosensibles
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 97.120 ISBN 978-2-8322-8066-9
– 2 – IEC 60730-2-9:2015/AMD2:2020
© IEC 2020
FOREWORD
This amendment has been prepared by IEC technical committee 72: Automatic electrical
controls.
The text of this amendment is based on the following documents:
FDIS Report on voting
72/1225/FDIS 72/1236/RVD
Full information on the voting for the approval of this amendment can be found in the report on
voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC website under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
•
...
Frequently Asked Questions
EN IEC 60730-2-9:2019/A2:2020 is a amendment published by CLC. Its full title is "Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls". This standard covers: 2019-03-19: to contact PM before proceeding with any assessment request.
2019-03-19: to contact PM before proceeding with any assessment request.
EN IEC 60730-2-9:2019/A2:2020 is classified under the following ICS (International Classification for Standards) categories: 97.120 - Automatic controls for household use. The ICS classification helps identify the subject area and facilitates finding related standards.
EN IEC 60730-2-9:2019/A2:2020 has the following relationships with other standards: It is inter standard links to EN IEC 60730-2-9:2019, prEN IEC 60730-2-9:2024. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN IEC 60730-2-9:2019/A2:2020 is associated with the following European legislation: EU Directives/Regulations: 2014/30/EU, 2014/35/EU; Standardization Mandates: M/511, M/552. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase EN IEC 60730-2-9:2019/A2:2020 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CLC standards.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...