EN 61300-2-37:2016
(Main)Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-37: Tests - Cable bending for fibre optic closures
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-37: Tests - Cable bending for fibre optic closures
IEC 61300-2-37:2016 describes a test for the effectiveness of the sealing and clamping hardware of a fibre optic closure when the cable entering or exiting the fibre optic closure is subjected to bending. This third edition cancels and replaces the second edition published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - substantial updating of Subclauses 4.1, 6.5, 6.7 and Figure 1; - addition of severities which are determined by the number and direction of cable bends, test temperature and overpressure for each environmental category according to IEC 61753-1. Keywords: sealing and clamping hardware of a fibre optic closure, cable bending
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-37: Prüfungen - Kabelbiegung bei Muffen
Dispositifs d'interconnexion et composants passifs fibroniques - Procédures fondamentales d'essais et de mesures - Partie 2-37: Essais - Courbure du câble pour les boîtiers pour fibres optiques
L'IEC 61300-2-37:2016 décrit un essai destiné à évaluer l'efficacité du dispositif d'étanchéité et de fixation d'un boîtier pour fibres optiques lorsque le câble qui entre ou qui sort du boîtier est soumis à un effort de courbure. Cette troisième édition annule et remplace la deuxième édition parue en 2006. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - mise à jour importante de 4.1, 6.5, 6.7 et de la Figure 1; - ajout de sévérités qui sont déterminées par le nombre et le sens des courbures des câbles, par la température d'essai et par la surpression pour chaque catégorie environnementale conformément à l'IEC 61753-1. Mots clés: étanchéité et de fixation d'un boîtier pour fibres optiques, câble courbure
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 2-37. del: Preskusi - Upogibanje kabla za ohišja optičnih kablov (IEC 61300-2-37:2016)
Ta del standarda IEC 61300 opisuje preskus učinkovitosti opreme za tesnjenje in spojitev ohišja optičnih kablov, kadar je kabel, ki je napeljan v notranjost ohišja ali iz njega, izpostavljen upogibanju.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 61300-2-37:2016
01-oktober-2016
1DGRPHãþD
SIST EN 61300-2-37:2007
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2VQRYQLSUHVNXVQLLQPHULOQL
SRVWRSNLGHO 3UHVNXVL8SRJLEDQMHNDEOD]DRKLãMDRSWLþQLKNDEORY ,(&
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-37: Tests - Cable bending for fibre optic closures (IEC
61300-2-37:2016)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-37: Prüfungen - Kabelbiegung bei Muffen (IEC 61300-2-37:2016)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes
fondamentales d'essais et de mesures - Partie 2-37: Essais - Efforts de flexion sur le
câble pour les boîtiers de fibres optiques (IEC 61300-2-37:2016)
Ta slovenski standard je istoveten z: EN 61300-2-37:2016
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 61300-2-37:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 61300-2-37:2016
---------------------- Page: 2 ----------------------
SIST EN 61300-2-37:2016
EUROPEAN STANDARD EN 61300-2-37
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2016
ICS 33.180.20 Supersedes EN 61300-2-37:2007
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures -
Part 2-37: Tests - Cable bending for fibre optic closures
(IEC 61300-2-37:2016)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren -
mesures - Partie 2-37: Essais - Courbure du câble pour les Teil 2-37: Prüfungen - Kabelbiegung bei Muffen
boîtiers pour fibres optiques (IEC 61300-2-37:2016)
(IEC 61300-2-37:2016)
This European Standard was approved by CENELEC on 2016-05-25. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61300-2-37:2016 E
---------------------- Page: 3 ----------------------
SIST EN 61300-2-37:2016
EN 61300-2-37:2016
European foreword
The text of document 86B/3975/FDIS, future edition 3 of IEC 61300-2-37, prepared by SC 86B “Fibre
optic interconnecting devices and passive components” of IEC/TC 86 “Fibre optics” was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-37:2016.
The following dates are fixed:
(dop) 2017-02-25
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2017-05-25
standards conflicting with the
document have to be withdrawn
This document supersedes EN 61300-2-37:2007.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61300-2-37:2016 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 61300-2-23 NOTE Harmonized as EN 61300-2-23.
IEC 61300-3-3 NOTE Harmonized as EN 61300-3-3.
IEC 61753-1 NOTE Harmonized as EN 61753-1.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.