Fibre optic interconnecting devices and passive components - Performance standard - Part 111-07: Sealed closures - Category A - Aerial

This part of IEC 61753 contains the minimum tests, test severities and measurement requirements which a sealed fibre optic closure need to meet in order to be categorised as meeting the IEC standard for category A - Aerial, as defined in Table A.13 of IEC 61753-1:2018. Free breathing closures are not covered in this document.

Lichtwellenleiter - Verbindungselemente und passive Bauteile – Betriebsverhalten – Teil 111-07: Druckdichte Muffen für die Kategorie A – Luftverlegung

Dispositifs d'interconnexion et composants passifs fibroniques - Norme de performance - Partie 111-07: Boîtiers étanches pour la catégorie A - Aériens

IEC 61753-111-07:2021 contient les essais minimaux, ainsi que les sévérités d’essai et les exigences de mesure minimales auxquels il est nécessaire qu’un boîtier à fibres optiques étanche satisfasse afin de pouvoir être classé comme satisfaisant à la norme IEC pour la catégorie A – Aériens, telle qu’elle est définie dans le Tableau A.13 de l’IEC 61753‑1:2018. Les boîtiers à ventilation libre ne sont pas couverts par le présent document. Cette première édition annule et remplace l’IEC 61753-111-7 parue en 2009. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'IEC 61753‑111‑7: a. mise à jour des termes et définitions conformément à l’IEC 61753-1:2018 et à l’IEC 61756‑1:2019; b. ajout des sévérités détaillées pour les essais de résistance des matériaux à la lumière UV et aux moisissures; c. mise à jour des sévérités d’essai selon la nouvelle édition de l’IEC 61753-1:2018; d. modification à 20 kPa de la surpression d’essai pour les essais d’étanchéité; e. ajout du critère d’acceptation/de rejet de la perte de pression en cours d’essai aux essais d’étanchéité mécanique; f. harmonisation des conditions d’essai en laboratoire avec l’IEC 61300-1 à une température de +23 °C ± 5 °C, sauf spécification contraire; g. ajout des fibres de type B-657. rayon de courbure minimal des fibres stockées conformément à l’IEC 61756-1:2019; h. modification de l’essai d’étanchéité aux vibrations (fréquence de 10 Hz, amplitude de 3 mm et 1 000 000 cycles); i. ajout de charges réduites dans l’essai de rétention du câble pour les câbles et les tubes de petit diamètre; j. ajout de charges réduites pour l’essai de compression axiale du câble pour les câbles et les tubes de petit diamètre; k. ajout de la durée des cycles dans l’essai de torsion et de courbure; l. suppression de l’essai de chute libre (couvert désormais par l'essai de choc optique); m. réduction à 5 cycles de la durée d’essai de montage et de démontage; n. réduction à 12 cycles de la durée de variations de température.

Optični spojni elementi in pasivne komponente - Izvedbeni standard - 111-07. del: Zatesnjene spojnice - Kategorija A - Nadzemna uporaba (IEC 61753-111-07:2021)

General Information

Status
Published
Publication Date
14-Oct-2021
Withdrawal Date
07-Oct-2022
Current Stage
6060 - Document made available - Publishing
Start Date
15-Oct-2021
Completion Date
15-Oct-2021

Relations

Buy Standard

Standard
EN IEC 61753-111-07:2021 - BARVE
English language
32 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2021
Nadomešča:
SIST EN 61753-111-7:2010
Optični spojni elementi in pasivne komponente - Izvedbeni standard - 111-07. del:
Zatesnjene spojnice - Kategorija A - Nadzemna uporaba (IEC 61753-111-07:2021)
Fibre optic interconnecting devices and passive components - Performance standard -
Part 111-07: Sealed closures - Category A - Aerial (IEC 61753-111-07:2021)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Betriebsverhalten - Teil
111-07: Druckdichte Muffen für die Kategorie A - Luftverlegung (IEC 61753-111-07:2021)
Dispositifs d'interconnexion et composants passifs fibroniques - Norme de performance -
Partie 111-07: Boîtiers étanches pour la catégorie A - Aériens (IEC 61753-111-07:2021)
Ta slovenski standard je istoveten z: EN IEC 61753-111-07:2021
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61753-111-07

NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2021
ICS 33.180.20 Supersedes EN 61753-111-7:2010 and all of its
amendments and corrigenda (if any)
English Version
Fibre optic interconnecting devices and passive components -
Performance standard - Part 111-07: Sealed closures - Category
A - Aerial
(IEC 61753-111-07:2021)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Norme de performance - Partie 111-07: Bauteile - Betriebsverhalten - Teil 111-07: Druckdichte
Boîtiers étanches pour la catégorie A - Aériens Muffen für die Kategorie A - Luftverlegung
(IEC 61753-111-07:2021) (IEC 61753-111-07:2021)
This European Standard was approved by CENELEC on 2021-10-08. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61753-111-07:2021 E

European foreword
The text of document 86B/4493/FDIS, future edition 1 of IEC 61753-111-07, prepared by SC 86B
“Fibre optic interconnecting devices and passive components” of IEC/TC 86 “Fibre optics” was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022–07–08
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022–10–08
document have to be withdrawn
This document supersedes EN 61753-111-7:2010 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61753-111-07:2021 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60068-1 NOTE Harmonized as EN 60068-1
IEC 60721-3-1 NOTE Harmonized as EN IEC 60721-3-1
IEC 60721-3-2 NOTE Harmonized as EN IEC 60721-3-2
IEC 60793-2 NOTE Harmonized as EN IEC 60793-2
IEC 60794-1-2 NOTE Harmonized as EN IEC 60794-1-2
IEC 60794-2 NOTE Harmonized as EN 60794-2
IEC 60794-3 NOTE Harmonized as EN 60794-3
IEC 61300 (series) NOTE Harmonized as EN 61300 (series)
IEC 62005 (series) NOTE Harmonized as EN IEC 62005 (series)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-2-10 - Environmental testing - Part 2–10: Tests - EN 60068-2-10 -
Test J and guidance: Mould growth
IEC 60793-2-50 - Optical fibres - Part 2–50: Product EN IEC 60793-2-50 -
specifications - Sectional specification for
class B single-mode fibres
IEC 61300-1 - Fibre optic interconnecting devices and EN 61300-1 -
passive components - Basic test and
measurement procedures - Part 1: General
and guidance
IEC 61300-2-1 - Fibre optic interconnecting devices and EN 61300-2-1 -
passive components - Basic test and
measurement procedures - Part 2–1: Tests
- Vibration (sinusoidal)
IEC 61300-2-4 - Fibre optic interconnecting devices and EN IEC 61300-2-4 -
passive components - Basic test and
measurement procedures - Part 2–4: Tests
- Fibre or cable retention
IEC 61300-2-5 - Fibre optic interconnecting devices and EN 61300-2-5 -
passive components - Basic test and
measurement procedures - Part 2–5: Tests
- Torsion
IEC 61300-2-9 - Fibre optic interconnecting devices and EN 61300-2-9 -
passive components - Basic test and
measurement procedures - Part 2–9: Tests
- Shock
IEC 61300-2-11 - Fibre optic interconnecting devices and EN 61300-2-11 -
passive components - Basic test and
measurement procedures - Part 2–11:
Tests - Axial compression
IEC 61300-2-12 - Fibre optic interconnecting devices and EN 61300-2-12 -
passive components - Basic test and
measurement procedures - Part 2–12:
Tests - Impact
IEC 61300-2-22 - Fibre optic interconnecting devices and EN 61300-2-22 -
passive components - Basic test and
measurement procedures - Part 2–22:
Tests - Change of temperature
IEC 61300-2-26 - Fibre optic interconnecting devices and EN 61300-2-26 -
passive components - Basic test and
measurement procedures - Part 2–26:
Tests - Salt mist
IEC 61300-2-33 - Fibre optic interconnecting devices and EN 61300-2-33 -
passive components - Basic test and
measurement procedures - Part 2–33:
Tests - Assembly and disassembly of fibre
optic mechanical splices, fibre
management systems and closures
IEC 61300-2-34 - Fibre optic interconnecting devices and EN 61300-2-34 -
passive components - Basic test and
measurement procedures - Part 2–34:
Tests - Resistance to solvents and
contaminating fluids of interconnecting
components and closures
IEC 61300-2-37 - Fibre optic interconnecting devices and EN 61300-2-37 -
passive components - Basic test and
measurement procedures - Part 2–37:
Tests - Cable bending for fibre optic
closures
IEC 61300-2-38 - Fibre optic interconnecting devices and EN 61300-2-38 -
passive components - Basic test and
measurement procedures - Part 2–38:
Tests - Sealing for pressurized fibre optic
closures
IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures - Part 3–1:
Examinations and measurements - Visual
examination
IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures - Part 3–3:
Examinations and measurements - Active
monitoring of changes in attenuation and
return loss
IEC 61300-3-28 - Fibre optic interconnecting devices and EN 61300-3-28 -
passive components - Basic test and
measurement procedures - Part 3–28:
Examinations and measurements -
Transient loss
IEC 61753-1 2018 Fibre optic interconnecting devices and EN IEC 61753-1 2018
passive components - Performance
standard - Part 1: General and guidance
IEC 61756-1 2019 Fibre optic interconnecting devices and EN IEC 61756-1 2020
passive components - Interface standard
for fibre management systems - Part 1:
General and guidance
ISO 4892-3 - Plastics - Methods of exposure to EN ISO 4892-3 -
laboratory light sources - Part 3:
Fluorescent UV lamps
IEC 61753-111-07 ®
Edition 1.0 2021-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Fibre optic interconnecting devices and passive components – Performance

standard –
Part 111-07: Sealed closures – Category A – Aerial

Dispositifs d’interconnexion et composants passifs fibroniques – Norme de

performance –
Partie 111-07: Boîtiers étanches pour la catégorie A – Aériens

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-1023-3

– 2 – IEC 61753-111-07:2021 © IEC 2021
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 Abbreviated terms . 11
5 General requirements . 11
5.1 Storage, transportation and packaging . 11
5.2 Installation and intervention . 11
5.3 Marking and identification . 12
5.4 Materials . 12
5.5 Safety . 12
6 Test . 13
6.1 General . 13
6.2 Test sample preparation . 13
6.3 Test and measurement methods . 13
6.4 Sample size . 13
6.5 Pass/fail criteria . 14
6.6 Test report . 14
7 Performance requirements. 14
7.1 Sealing, optical and visual examination pass/fail criteria . 14
7.2 Sealing performance requirements . 16
7.3 Optical performance requirements . 18
Annex A (normative) Sample definition . 21
A.1 Fibre type for test sample . 21
A.2 Closure optical test sample configuration . 22
Annex B (normative) Intervention and reconfiguration/resplicing .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.