iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 50065-4-3:2003

(Main)

Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-3: Low voltage decoupling filter - Incoming filter

Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-3: Low voltage decoupling filter - Incoming filter

This standard applies to incoming filters used to control the coupling of signals between the utility area and the consumer area (see Figure 1). The standard defines • the minimum impedance in the relevant frequency band(s) at both Utility port and Consumer port, • the minimum attenuation of unwanted signals transmitted from the utility side to the consumer side and vice versa, • the transmission characteristics: - operating frequency domain for both utility side and consumer side, - attenuation between the utility side and the consumer side and vice versa, - impedance at the utility side and at the consumer side. This standard applies to incoming filters designed for and used in single or multiphase installations.

Signalübertragung auf elektrischen Niederspannungsnetzen im Frequenzbereich 3 kHz bis 148,5 kHz - Teil 4-3: Niederspannungs-Entkopplungsfilter - Eingangsfilter

Transmission de signaux sur les réseaux électriques basse tension dans la bande de fréquences de 3 kHz à 148,5 kHz - Partie 4-3: Filtres basse tension de découplage - Filtre de branchement

Signalizacija po nizkonapetostnih električnih napeljavah v frekvenčnem območju od 3 kHz do 148,5 kHz – 4-3. del: Nizkonapetostni ločilni filtri – Vhodni filter

General Information

Status
Published
Publication Date
22-Jan-2003
Withdrawal Date
31-Jul-2004
ICS
31.160 - Electric filters
33.040.30 - Switching and signalling systems
Technical Committee
CLC/TC 205A - Mains communicating systems
Drafting Committee
ISO/IEC/JTC 1/SC25 - ISO/IEC_JTC_1/SC25
Parallel Committee
ISOIEC/JTC 1/SC25 - ISOIEC_JTC_1/SC25
Current Stage
6060 - Document made available - Publishing
Start Date
23-Jan-2003
Completion Date
23-Jan-2003
Ref Project
SIST EN 50065-4-3:2004 - Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz -- Part 4-3: Low voltage decoupling filter - Incoming filter

Relations

Replaced By
EN 50065-4-3:2023 - Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-3: Low voltage decoupling filter - Incoming filter
Effective Date
14-May-2019

Buy Standard

EN 50065-4-3:2004EN 50065-4-3:2004
PreviousNext
Standard
EN 50065-4-3:2004
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI SIST EN 50065-4-3:2004

STANDARD
marec 2004
Signalizacija po nizkonapetostnih električnih napeljavah v frekvenčnem
območju od 3 kHz do 148,5 kHz – 4-3. del: Nizkonapetostni ločilni filtri –
Vhodni filter
Signalling on low-voltage electrical installations in the frequency range 3 kHz to
148,5 kHz - Part 4-3: Low voltage decoupling filter - Incoming filter
ICS 31.160; 33.040.30 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 50065-4-3
NORME EUROPÉENNE
EUROPÄISCHE NORM January 2003

ICS 31.160; 33.040.30
English version
Signalling on low-voltage electrical installations
in the frequency range 3 kHz to 148,5 kHz
Part 4-3: Low voltage decoupling filter -
Incoming filter
Transmission de signaux sur les réseaux Signalübertragung auf elektrischen
électriques basse tension dans la bande Niederspannungsnetzen
de fréquences de 3 kHz à 148,5 kHz im Frequenzbereich 3 kHz bis 148,5 kHz
Partie 4-3: Filtres basse tension Teil 4-3: Niederspannungs-
de découplage - Entkopplungsfilter -
Filtre de branchement Eingangsfilter

This European Standard was approved by CENELEC on 2001-09-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 50065-4-3:2003 E
Foreword
This European Standard was prepared by SC 205A, Mains communicating systems, of Technical
Committee CENELEC TC 205, Home and Building Electronic Systems (HBES).
The text of the draft was submitted to the Unique Acceptance Procedure and was approved by
CENELEC as EN 50065-4-3 on 2001-09-01.
The following dates were fixed:
- latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2003-08-01

- latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2004-08-01
EN 50065 consists of the following parts, under the general title: Signalling on low-voltage electrical
installations in the frequency range 3 kHz to 148,5 kHz
Part 1 General requirements, frequency bands and electromagnetic disturbances
Part 2-1 Immunity requirements for mains communications equipment and systems
operating in the range of frequencies 95 kHz to 148,5 kHz and intended for use in
residential, commercial and light industrial environments
Part 2-2 Immunity requirements for mains communications equipment and systems
operating in the range of frequencies 95 kHz to 148,5 kHz and intended for use in
industrial environments
Part 2-3 Immunity requirements for mains communications equipment and systems
operating in the range of frequencies 3 kHz to 95 kHz and intended for use by
electricity suppliers and distributors
Part 4-1 Low voltage decoupling filters – Generic specification
Part 4-2 Low voltage decoupling filters – Safety requirements
Part 4-3 Low voltage decoupling filters – Incoming filter
Part 4-4 Low voltage decoupling filters – Impedance filter
Part 4-5 Low voltage decoupling filters – Segmentation filter
Part 4-6 Low voltage decoupling filters – Phase coupler
Part 7 Equipment impedance
__________
- 3 - EN 50065-4-3:2003
Contents
Page
1 Scope.4
2 Normative references.4
3 Classification.5
3.1 Type 1.5
3.2 Type 2.5
3.3 Type 3.5
4 Incoming filter electrical characteristics .5
4.1 Over voltage.5
4.2 EMC.5
4.3 Operating frequency range .6
4.4 Impedance.6
4.5 Transfer function.7
Figure 1 - The application of incoming filter .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 50065-4-5:2023(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz Part 4-5: Low voltage decoupling filter - Segmentation filter
SIST EN 50065-4-5:2023

This document applies to segmentation filters in a mains communication system intended for utility networks or household and similar fixed installation including residential, commercial and light industrial buildings. These filters are used to control the coupling of signals between two areas of a mains communication system, as illustrated in Figure 1. This document defines in the relevant frequency range: - the minimum impedance at both ports of the filter, - the minimum attenuation of signals transmitted between the ports of the filter. [Figure 1 - Application of segmentation filters]

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-4:2023(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-4: Low voltage decoupling filter - Impedance filter
SIST EN 50065-4-4:2023

This document applies to impedance filters in a mains communication system, intended for utility networks or household and similar fixed installation including residential, commercial and light industrial buildings. These filters are used to set a suitable impedance, in the nominal frequency range of the mains signalling system, at any point of the low voltage mains network where a low impedance equipment is connected, as shown in Figure 1, in order to allow reliable operation of the mains signalling system. Impedance filters can be used either in utility or consumer networks. They can also be used in conjunction with incoming filters and segmentation filters. [Figure 1 - The application of impedance filters]

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-6:2023(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz Part 4-6: Low voltage decoupling filters - Phase coupler
SIST EN 50065-4-6:2023

This document applies to phase couplers in a mains communication system intended for utility networks or household and similar fixed installation including residential, commercial and light industrial buildings. Phase couplers are used to control the coupling of communication signals between phases or sections of a mains communication system. This document defines - the requirements to ensure a minimum coupling between the phases or sections of a mains communication system, and - the requirements to ensure no change on the safety of the electrical installation.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-3:2023(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-3: Low voltage decoupling filter - Incoming filter
SIST EN 50065-4-3:2023

This document applies to incoming filters used to control the coupling of signals between the utility area and the consumer area, as illustrated in Figure 1. This document defines: - the minimum impedance in the relevant frequency band(s) at both utility port and consumer port, - the minimum attenuation of unwanted signals transmitted from the utility side to the consumer side and vice versa. This document applies to incoming filters designed for single or multiphase installations. [Figure 1 - The application of incoming filter]

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-1:2023(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-1: Low voltage decoupling filters - Generic specification
SIST EN 50065-4-1:2023

This document applies to decoupling filters installed on the low voltage mains network and operating in the frequency range 3 kHz to 148,5 kHz. It does not apply to EMI suppression filters incorporated in household equipment or other general electric equipment. It specifies the definitions, requirements and test methods of the functional, technical and environmental characteristics of the decoupling filter, e.g. impedance, transfer function, voltage drop, leakage current and power dissipation. The impedance and the transfer function are referred to the decoupling filter mains power ports (see Figure 1).

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-7:2005(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz - Part 4-7: Portable low voltage decoupling filters - Safety requirements
SIST EN 50065-4-7:2006

This European product safety standard applies to the filter part of portable devices for household and similar uses (hereafter referred to as portable decoupling filters) consisting of the filter part, a plug or an appliance inlet or a provision for connection by terminals or with a non-rewirable cord and one (multiple) socket-outlet or an appliance outlet. They are intended for single-phase circuits for nominal currents not exceeding 16 A and for nominal voltages not exceeding 250 V a.c. to neutral operating in the frequency range 3 kHz to 148,5 kHz and from 1,6 MHz to 30 MHz. The filtering functions are described in EN 50065-4-1. This standard does not cover phase couplers. Portable decoupling filters shall not be used as part of the fixed installation, where EN 50065-4-2 applies. Plugs and socket-outlets connected to the filter part and plugs and socket-outlets integrated with the filter part shall comply with the relevant national standard(s). Appliance inlets and appliance outlets connected to the filter part shall comply with the relevant parts of the EN 60320 series. Appliance inlets and appliance outlets integrated with the filter parts are not covered by this standard. This standard can be used for portable mains communication devices when no other product standard exists. This standard can be used for other portable mains filters other than those described in EN 50065-4-1 when no other product standard exists. Filters including batteries are not covered by this standard.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-2:2001/A2:2005(Amendment)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz - Part 4-2: Low voltage decoupling filters - Safety requirements
SIST EN 50065-4-2:2003/A2:2005
  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-6:2004(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-6: Low voltage decoupling filters - Phase coupler
SIST EN 50065-4-6:2005

This European Standard applies to phase couplers in a mains communication system for phase to neutral voltage not exceeding 250 V a.c. and a nominal current not exceeding 125 A, intended for household and similar fixed installation including residential, commercial and light industrial buildings. This European Standard applies to phase couplers used to control the coupling of communication signals between phases or sections of a mains communication system. A “phase coupler” may be used to achieve coupling between the phases of a multiphase installation, or to provide bridging of signals around other system components. The standard defines  the requirements to ensure a minimum coupling between the sections, and  the requirements to ensure no change on the safety of the electrical installation.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-4:2003(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-4: Low voltage decoupling filter - Impedance filter
SIST EN 50065-4-4:2004

This standard applies to impedance filters in a mains communication system for phase to neutral voltage not exceeding 250 V a.c. and a nominal current not exceeding 125 A, intended for household and similar fixed installation including residential, commercial and light industrial buildings. This standard also applies to "plug-in filters". These filters (see Figure 1) are used to set a suitable impedance, in the nominal frequency range of the mains signalling system, at any point of the low voltage mains network where a low impedance equipment is connected, in order to allow reliable operation of mains signalling system. These impedance filters can be used either in utility or consumer networks. They may also be used in conjunction with incoming filters and segmentation filters.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50065-4-5:2003(Main)
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 4-5: Low voltage decoupling filter - Segmentation filter
SIST EN 50065-4-5:2004

This standard applies to segmentation filters in a mains communication system used for single or multiphase installations having a phase to neutral voltage not exceeding 250 V a.c. and a nominal current not exceeding 125 A, intended for household and similar fixed installation including residential, commercial and light industrial buildings and utility networks. These filters (see Figure 1) are used to control the coupling of signals between two areas of a mains communication system. The standard defines -the minimum impedance in the relevant frequency range(s) at both ports, -the minimum attenuation of signals transmitted between port.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day