iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60286-3:2013/AC:2013

(Corrigendum)

Packaging of components for automatic handling - Part 3: Packaging of surface mount components on continuous tapes

Packaging of components for automatic handling - Part 3: Packaging of surface mount components on continuous tapes

This part of IEC 60286 is applicable to the tape packaging of electronic components without leads or with lead stumps, intended to be connected to electronic circuits. It includes only those dimensions that are essential for the taping of components intended for the abovementioned purposes. This standard also includes requirements related to the packaging of singulated die products including bare die and bumped die (flip chips).

Gurtung und Magazinierung von Bauelementen für automatische Verarbeitung - Teil 3: Gurtung von oberflächenmontierbaren Bauelementen auf Endlosgurten

Emballage de composants pour opérations automatisées - Partie 3: Emballage des composants pour montage en surface en bandes continues

Pakiranje komponent za avtomatsko ravnanje - 3. del: Pakiranje komponent za površinsko montažo na neprekinjenih trakovih

Ta del standarda IEC 60286 se uporablja za tračno pakiranje elektronskih komponent brez vodov ali ostankov vodov, namenjenih za povezavo z elektronskimi vezji. Vključuje samo dimenzije, bistvene za tračno pakiranje komponent, ki so namenjene za zgoraj navedene namene. Ta standard vključuje tudi zahteve glede pakiranja proizvodov s singularnimi polprevodniškimi integriranimi vezji, vključno s tistimi brez ohišja in tistimi z izboklinami (»flip chip«).

General Information

Status
Withdrawn
Publication Date
31-Oct-2013
ICS
31.020 - Electronic components in general
31.240 - Mechanical structures for electronic equipment
Technical Committee
CLC/SR 40 - Capacitors and resistors for electronic equipment
Drafting Committee
IEC/TC 40 - IEC_TC_40
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
20-Feb-2022
Completion Date
20-Feb-2022
Ref Project
SIST EN 60286-3:2013/AC:2014 - Packaging of components for automatic handling -- Part 3: Packaging of surface mount components on continuous tapes

Relations

Replaced By
EN IEC 60286-3:2019 - Packaging of components for automatic handling - Part 3: Packaging of surface mount components on continuous tapes
Effective Date
23-Jan-2023
Corrects
EN 60286-3:2013 - Packaging of components for automatic handling - Part 3: Packaging of surface mount components on continuous tapes
Effective Date
28-Jan-2023

Buy Standard

EN 60286-3:2013/AC:2014EN 60286-3:2013/AC:2014
PreviousNext
Corrigendum
EN 60286-3:2013/AC:2014
English language
1 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Pakiranje komponent za avtomatsko ravnanje - 3. del: Pakiranje komponent za površinsko montažo na neprekinjenih trakovihGurtung und Magazinierung von Bauelementen für die automatische Verarbeitung -- Teil 3: Gurtung von oberflächenmontierbaren Bauelementen auf EndlosgurtenEmballage de composants pour opérations automatisées -- Partie 3: Emballage des composants pour montage en surface en bandes continuesPackaging of components for automatic handling -- Part 3: Packaging of surface mount components on continuous tapes55.060Tulci. VretenaSpools. Bobbins31.020Elektronske komponente na
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60286-2:2022(Main)
Packaging of components for automatic handling - Part 2: Tape packaging of components with unidirectional leads on continuous tapes
SIST EN IEC 60286-2:2023

IEC 60286-2:2022 applies to the tape packaging of components with two or more unidirectional leads for use in electronic equipment. It provides dimensions and tolerances necessary to tape components with unidirectional leads. In general, the tape is applied to the component leads. It covers requirements for taping techniques used with equipment for automatic handling, pre-forming of leads, insertion and other operations and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes. This edition includes the following significant technical changes with respect to the previous edition: a) complete revision of structure; b) consolidation of essential parameters and requirements in Clause 4.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60286-3:2022(Main)
Packaging of components for automatic handling - Part 3: Packaging of surface mount components on continuous tapes
SIST EN IEC 60286-3:2023

This part of IEC 60286 is applicable to the tape packaging of electronic components without leads or with lead stumps, intended to be connected to electronic circuits. It includes only those dimensions that are essential for the taping of components intended for the above-mentioned purposes. This document also includes requirements related to the packaging of singulated die products including bare die and bumped die (flip chips).

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60286-1:2017/A1:2021(Amendment)
Packaging of components for automatic handling - Part 1: Tape packaging of components with axial leads on continuous tapes
SIST EN 60286-1:2018/A1:2021

No scope available

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60286-3:2019(Main)
Packaging of components for automatic handling - Part 3: Packaging of surface mount components on continuous tapes
SIST EN IEC 60286-3:2019

IEC 60286-3:2019 is available as IEC 60286-3:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60286-3:2019 is applicable to the tape packaging of electronic components without leads or with lead stumps, intended to be connected to electronic circuits. It includes only those dimensions that are essential for the taping of components intended for the above-mentioned purposes. This document also includes requirements related to the packaging of singulated die products including bare die and bumped die (flip chips). This edition includes the following significant technical changes with respect to the previous edition: - addition of a table of the classification to symbols concerning tape, reel and common symbols; - additions of a figure of example of polarity and orientation and a figure of example of dot seal; - revision of requirements for camber; - addition of a definition of design value with regard to tilt.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60286-1:2017(Main)
Packaging of components for automatic handling - Part 1: Tape packaging of components with axial leads on continuous tapes
SIST EN 60286-1:2018

IEC 60286-1:2017(E) applies to the tape packaging of components with axial leads for use in electronic equipment. In general, the tape is applied to the component leads. It covers requirements for taping techniques used with equipment for the preforming of leads, automatic handling, insertion and other operations, and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes. This edition includes the following significant changes with respect to the previous edition: a) a complete revision of the structure (detailed in Annex A) and reworked layout.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60286-2:2015(Main)
Packaging of components for automatic handling - Part 2: Tape packaging of components with unidirectional leads on continuous tapes
SIST EN 60286-2:2015

IEC 60286-2:2015 applies to the tape packaging of components with two or more unidirectional leads for use in electronic equipment. In general, the tape is applied to the component leads. It covers requirements for taping techniques used with equipment for automatic handling, pre-forming of leads, insertion and other operations and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes. This edition includes the following significant changes with respect to the previous edition: - A complete revision of the structure and reworked layout. - A two page overview containing a clear overview of all symbols and references. - Addition of annexes of known radial tape formats. - Improved figures.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60286-4:2013(Main)
Packaging of components for automatic handling - Part 4: Stick magazines for electronic components encapsulated in packages of different forms
SIST EN 60286-4:2014

IEC 60286-4:2013 is applicable to stick magazines (including end stoppers) intended to be used for storage of electronic components, for transport from the manufacturer to the customer and for in-house use in the manufacturing plant. They are also used to feed automatic placement machines for surface mounting as well as for through-hole mounting of electronic components. This edition includes the following significant technical changes with respect to the previous edition: Clause 4 describes the guidelines for customer specific stick magazine design. It replaces the magazine design rules for IEC outlined components and rules for orientation of components in stick magazines which have been moved to Annexes A to D.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60286-3-2:2009(Main)
Packaging of components for automatic handling - Part 3-2: Packaging of surface mount components on continuous tapes - Type VI - Blister carrier tapes of 4 mm width
SIST EN 60286-3-2:2009

IEC 60286-3-2:2009(E) is applicable to the tape packing of ultra small surface mount components using plastic blister carrier tape of 4 mm in width which has concave cavities for containing components of 1 mm in pitch of the component compartments (W4P1).

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60286-3-1:2009(Main)
Packaging of components for automatic handling – Part 3-1: Packaging of surface mount components on continuous tapes - Type V - Pressed carrier tapes
SIST EN 60286-3-1:2009

IEC 60286-3-1:2009(E) is applicable to the taping of surface mount components using carrier tapes which have concave cavities formed by compression of the base material.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60286-2:2022(Main)
Packaging of components for automatic handling - Part 2: Tape packaging of components with unidirectional leads on continuous tapes
SIST EN IEC 60286-2:2023

IEC 60286-2:2022 applies to the tape packaging of components with two or more unidirectional leads for use in electronic equipment. It provides dimensions and tolerances necessary to tape components with unidirectional leads. In general, the tape is applied to the component leads. It covers requirements for taping techniques used with equipment for automatic handling, pre-forming of leads, insertion and other operations and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes. This edition includes the following significant technical changes with respect to the previous edition: a) complete revision of structure; b) consolidation of essential parameters and requirements in Clause 4.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day