Aerospace series - Round bars, drawn, in aluminium and aluminium alloys - Tolerance class h 11 - Diameter 4 mm < D < 63 mm - Dimensions

This standard specifies the dimensions and tolerances of:
Round bars, drawn
in aluminium and aluminium alloys
Tolerance class h 11
Diameter 4 mm < D < 63 mm
for aerospace applications.

Luft- und Raumfahrt - Rundstangen, gezogen, aus Aluminium und Aluminiumlegierungen - Toleranzklasse h 11 - Durchmesser 4 mm = D = 63 mm - Maße

Diese Norm legt die Maße und Toleranzen von:
Rundstangen, gezogen
aus Aluminium und Aluminiumlegierungen
Toleranzklasse h11
Durchmesser 4 mm = D = 63 mm
für Anwendungen in der Luft- und Raumfahrt fest.

Série aérospatiale - Barres rondes, étirées en aluminium et alliages d'aluminium - Classe de tolérance h 11 - Diamètres 4 mm < D < 63 mm - Dimensions

La présente norme spécifie les dimensions et les tolérances des :
Barres rondes, étirées
en aluminium et alliages d'aluminium
Classe de tolérance h 11
Diamètres 4 mm < D < 63 mm
pour applications aérospatiales.

Aerospace series - Round bars, drawn, in aluminium and aluminium alloys - Tolerance class h 11 - Diameter 4 mm < D < 63 mm - Dimensions

General Information

Status
Published
Publication Date
04-Dec-2001
Withdrawal Date
29-Jun-2002
Technical Committee
Drafting Committee
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
01-Jun-2017

Buy Standard

Standard
EN 2044:2004
English language
5 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Round bars, drawn, in aluminium and aluminium alloys - Tolerance class h 11 - Diameter 4 mm < D < 63 mm - DimensionsLuft- und Raumfahrt - Rundstangen, gezogen, aus Aluminium und Aluminiumlegierungen - Toleranzklasse h 11 - Durchmesser 4 mm = D = 63 mm - MaßeSérie aérospatiale - Barres rondes, étirées en aluminium et alliages d'aluminium - Classe de tolérance h 11 - Diametres 4 mm < D < 63 mm - DimensionsAerospace series - Round bars, drawn, in aluminium and aluminium alloys - Tolerance class h 11 - Diameter 4 mm < D < 63 mm - Dimensions49.025.20AluminijAluminiumICS:Ta slovenski standard je istoveten z:EN 2044:2001SIST EN 2044:2004en01-maj-2004SIST EN 2044:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2044December 2001ICS 49.025.20English versionAerospace series - Round bars, drawn, in aluminium andaluminium alloys - Tolerance class h 11 - Diameter 4 mm
D 63 mm - DimensionsSérie aérospatiale - Barres rondes, étirées, en aluminiumet alliages d'aluminium - Classe de tolérance h 11 -Diamètres 4 mm
D
63 mm - DimensionsLuft- und Raumfahrt - Rundstangen, gezogen, ausAluminium und Aluminiumlegierungen - Toleranzklasse h11 - Durchmesser 4 mm
D
63 mm - MaßeThis European Standard was approved by CEN on 2 May 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2044:2001 ESIST EN 2044:2004
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.