iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13126-6:2018

(Main)

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 6: Variable geometry stay hinges (with or without a friction stay)

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 6: Variable geometry stay hinges (with or without a friction stay)

This part of EN 13126 specifies requirements and test methods for durability, strength, security and function of mechanically operated variable/parallel geometry stay hinges (with or without a friction system) whether fitted, with integral restrictors or not, in accordance with common application as shown in informative Annex D.
By means of this standard, the user of recognized tested hardware can assume that with correct usage, the variable/parallel geometry stay hinges (with or without a friction system) for windows conform to prescribed requirements.
NOTE 1 Balancing stay arms/hinges do not represent a friction system.
NOTE 2 For the purposes of this standard, the friction system is achieved by friction pads or similar.

Baubeschläge - Beschläge für Fenster und Fenstertüren - Anforderungen und Prüfverfahren - Teil 6: Scheren mit veränderlicher Geometrie (mit oder ohne Friktionssystem)

Dieser Teil der Normenreihe EN 13126 legt die Anforderungen und Prüfverfahren für die Dauer-funktionsfähigkeit, Festigkeit, Schutzwirkung und Funktionsweise von mechanisch betätigten Scheren mit veränderlicher/paralleler Geometrie (mit oder ohne Friktionssystem), egal ob mit oder ohne eingebauter Vorrichtung zur Begrenzung des Öffnungswinkels, entsprechend den im informativen Anhang D dar-gestellten üblichen Anwendungen fest.
Mit Hilfe dieser Norm kann der Anwender von anerkannten geprüften Baubeschlägen davon ausgehen, dass die Scheren mit veränderlicher/paralleler Geometrie (mit oder ohne Friktionssystem) für Fenster bei richtigem Gebrauch die vorgeschriebenen Anforderungen erfüllen.
ANMERKUNG 1 Aussteller/Ausstellscheren stellen kein Friktionssystem dar.
ANMERKUNG 2 Für die Anwendung dieser Norm wird das Friktionssystem durch Bremsplatten oder etwas Gleichartiges erreicht.

Quincaillerie pour le bâtiment - Exigences et méthodes d’essai des ferrures de fenêtres et portes-fenêtres - Partie 6 : Compas à géométrie variable (avec ou sans système de friction)

La présente partie de l’EN 13126 spécifie les exigences et les méthodes d’essai relatives à l’endurance, à la résistance, à la sécurité des biens et au fonctionnement des compas mécaniques à géométrie variable/parallèle (avec ou sans système de friction), qu’ils soient équipés ou non de limitateurs d’ouverture intégrés, en conformité avec leur application courante représentée dans l’Annexe D informative.
La présente norme permet à l’utilisateur d’une ferrure éprouvée par essai de considérer que lorsqu’ils sont utilisés correctement, les compas à géométrie variable/parallèle (avec ou sans système de friction) des fenêtres sont conformes aux exigences spécifiées.
NOTE 1   Les compas ou bras de compas d’équilibrage ne constituent pas un système de friction.
NOTE 2   Pour les besoins de la présente norme, la friction est réalisée par des patins de friction ou des pièces similaires.

Stavbno okovje - Okovje za okna in zastekljena vrata - Zahteve in preskusne metode - 6. del: Oporni tečaji z različno geometrijo (s sistemom trenja ali brez njega)

Ta del standarda prEN 13126 določa zahteve in preskusne metode za trajnost, trdnost, varnost in delovanje mehansko upravljanih opornih tečajev z različno/vzporedno geometrijo (s sistemom trenja ali brez njega) ter nameščenimi zaklepi ali brez njih v skladu z običajno uporabo, kot je podana v informativnem dodatku D.
Na podlagi tega standarda lahko uporabnik priznanega preskušenega okovja sklepa, da pravilna uporaba opornih tečajev z različno/vzporedno geometrijo (s sistemom trenja ali brez njega) za okna omogoča skladnost z opisanimi zahtevami.
OPOMBA 1:   Izravnalne oporne ročice/tečaji ne predstavljajo sistema trenja.
OPOMBA 2:   Za namene tega standarda je sistem trenja dosežen z zavorno ploščico ali podobnim elementom.

General Information

Status
Published
Publication Date
14-Aug-2018
Withdrawal Date
27-Feb-2019
ICS
91.190 - Building accessories
Technical Committee
CEN/TC 33 - Doors, windows, shutters and building hardware
Drafting Committee
CEN/TC 33/WG 4 - Building hardware
Current Stage
Ref Project
SIST EN 13126-6:2018 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 6: Variable geometry stay hinges (with or without a friction stay)

Relations

Replaces
EN 13126-6:2008 - Building hardware - Requirements and test methods for windows and doors height windows - Part 6: Variable geometry stay hinges (with or without a friction stay)
Effective Date
08-Jun-2022

Buy Standard

EN 13126-6:2018EN 13126-6:2018
PreviousNext
Standard
EN 13126-6:2018
English language
40 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-oktober-2018
1DGRPHãþD
SIST EN 13126-6:2009
6WDYEQRRNRYMH2NRYMH]DRNQDLQ]DVWHNOMHQDYUDWD=DKWHYHLQSUHVNXVQH
PHWRGHGHO2SRUQLWHþDML]UD]OLþQRJHRPHWULMR VVLVWHPRPWUHQMDDOLEUH]
QMHJD
Building hardware - Hardware for windows and door height windows - Requirements and
test methods - Part 6: Variable geometry stay hinges (with or without a friction stay)
Baubeschläge - Beschläge für Fenster und Fenstertüren - Anforderungen und
Prüfverfahren - Teil 6: Scheren mit veränderlicher Geometrie (mit oder ohne
Friktionssystem)
Quincaillerie pour le bâtiment - Exigences et méthodes d’essai des ferrures de fenêtres
et portes-fenêtres - Partie 6 : Compas à géométrie variable (avec ou sans système de
friction)
Ta slovenski standard je istoveten z: EN 13126-6:2018
ICS:
91.190 Stavbna oprema Building accessories
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13126-6
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2018
EUROPÄISCHE NORM
ICS 91.190 Supersedes EN 13126-6:2008
English Version
Building hardware - Hardware for windows and door
height windows - Requirements and test methods - Part 6:
Variable geometry stay hinges (with or without a friction
stay)
Quincaillerie pour le bâtiment - Exigences et méthodes Baubeschläge - Beschläge für Fenster und Fenstertüren
d'essai des ferrures de fenêtres et portes-fenêtres - - Anforderungen und Prüfverfahren - Teil 6: Scheren
Partie 6 : Compas à géométrie variable (avec ou sans mit veränderlicher Geometrie (mit oder ohne
système de friction) Friktionssystem)
This European Standard was approved by CEN on 30 April 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13126-6:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Classification . 7
4.1 General . 7
4.2 Durability (1 – first box) . 8
4.3 Mass (2 – second box) . 8
4.4 Corrosion resistance (3 – third box) . 8
4.5 Test sizes (4 – fourth box) . 8
4.6 Application (5 – fifth box) . 10
4.7 Example of classification for variable/parallel geometry stay hinges . 10
5 Requirements . 10
5.1 Dangerous substances . 10
5.2 Integrated restrictors . 11
5.3 Durability . 11
5.4 Pull-in and pull-in abuse test . 11
5.5 Parallelism test . 11
5.6 Friction test (where applicable) . 11
5.7 Obstructed track test . 12
5.8 Ease of sash movement test . 12
5.9 Durability test. 12
5.10 Simulated negative pressure test . 13
5.11 Static load test . 13
5.12 Additional load test . 14
5.13 Corrosion resistance . 14
6 Test equipment and preparation for the test . 14
6.1 Test-rig . 14
6.2 Specimen . 14
6.3 Mounting of specimen . 15
6.4 Additional equipment. 15
6.4.1 Block for pull-in abuse test . 15
6.4.2 Steel cross for simulated negative pressure test . 15
7 Test procedures . 15
7.1 Samples . 15
7.2 General . 15
7.3 Adjusting the sash-mass . 16
7.4 Lubrication and adjustment of hardware . 16
7.5 Pull-in test . 16
7.5.1 General . 16
7.5.2 Pull-in test procedure . 16
7.5.3 Acceptance criteria . 16
7.6 Friction test . 17
7.6.1 General . 17
7.6.2 Friction test procedure . 17
7.6.3 Acceptance criteria . 17
7.7 Obstructed track test . 17
7.7.1 Procedure – side hung and top hung windows . 17
7.7.2 Procedure – parallel opening windows . 18
7.7.3 Acceptance criteria . 18
7.8 Pull-in abuse test . 18
7.8.1 General . 18
7.8.2 Procedure – pull-in abuse test . 18
7.8.3 Acceptance criteria . 19
7.9 Ease of sash movement test . 19
7.9.1 Procedure – side and top hung opening windows . 19
7.9.2 Procedure – parallel opening windows . 19
7.9.3 Acceptance criteria . 19
7.10 Durability test . 20
7.10.1 Procedure – top hung and side hung windows . 20
7.10.2 Procedure – parallel opening windows . 20
7.10.3 Cycles . 20
7.10.4 Egress easy clean side hung windows . 20
7.10.5 Acceptance criteria . 20
7.11 Simulated negative pressure test (excluding parallel windows) . 21
7.11.1 Procedure . 21
7.11.2 Acceptance criteria . 21
7.12 Static load test procedure . 21
7.12.1 Procedure . 21
7.12.2 Acceptance criteria . 22
7.13 Additional load test . 22
7.13.1 Procedure .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 16867:2020+A2:2024(Main)
Building hardware - Mechatronic door furniture - Requirements and test methods
SIST EN 16867:2020+A2:2024

1.1   General
This document applies to Mechatronic door furniture (MDF) fitted on the door set which gives the possibility to control the locking and/or release part through an electronic authorization means. This can be operable by credentials (i.e. card, code, biometric).
The MDF according to this document is combined with locks according to EN 12209, EN 14846, prEN 15685 or may be a part of an emergency exit device according to EN 179, EN 1125 or EN 13637.
The MDF may be standalone or linkable to an external control system.
The document would allow classifying the MDF upon several characteristics such as category of use, durability, environmental, security, and type of operating device.
The suitability of the MDF for use on fire or smoke-door assemblies is determined by fire resistance tests conducted in addition to the performance testing specified by this document.
1.2   Exclusions
This document does not cover:
-   mechatronic cylinders according to EN 15684;
-   electromechanical operated locks and striking plates according to EN 14846.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16035:2023(Main)
Hardware performance sheet (HPS) - Identification and summary of test evidence to facilitate the inter-changeability of building hardware for application to fire resisting and/or smoke control doorsets and/or openable windows
SIST EN 16035:2024

This document summarizes relevant results and classifications from tests of the fire and smoke resistance performance of building hardware in the format of a hardware performance sheet (HPS). This document provides guidance and requirements on the minimum data required as a basis for the preparation of EXAP reports for the interchangeability of building hardware on fire-retardant and/or smoke-tight doors and openable windows.
This document identifies the performance characteristics and the requirements for building hardware which can be found in the appropriate product standards.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-3:2023(Main)
Building hardware - Hardware for windows and door-height windows - Requirements and test methods - Part 3: Handles, primarily for Tilt and Turn, Tilt-First and Turn-Only hardware
SIST EN 13126-3:2023

This part of the EN 13126 series specifies the requirements and test procedures for durability, strength, security and functionality of handles.
This document is applicable to Tilt and Turn, Tilt-First and Turn-Only hardware for use on windows and door-height windows.
Handles can also be used on other opening types, e.g. on In-line Sliding, Tilt and Slide, Sliding Folding, horizontal and vertical-pivoting windows.
This document is not applicable to:
a)   operation devices, door handles for door latches and door locks (for this, refer to EN 1906);
b)   handles with handle length > 170 mm (refer to Figure B.1).

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17610:2022(Main)
Building hardware - Environmental product declarations - Product category rules complementary to EN 15804 for building hardware
SIST EN 17610:2022

This document provides product category rules (PCR) for Type III environmental declarations for:
- Building hardware products for opening and closing doors, gates, windows and shutters:
-- Lever handles and knob furniture (EN 1906);
-- Single-axis hinges (EN 1935);
-- Hardware for windows and door height windows (EN 13126 (all parts));
-- Fittings for shutters (e.g. EN 14648);
-- Controlled door closing devices, electrically powered hold-open devices for swing doors and door coordinator devices (EN 1154, EN 1155, EN 1158);
-- Hardware for sliding doors, folding doors and roll fronts (EN 1527, EN 15706);
-- Glass door gear;
- Building hardware products for locking and unlocking doors, gates, windows and shutters:
-- Mechanically operated locks and locking plates, multipoint locks, latches and locking plates (EN 12209, EN 15685 );
-- Cylinders for locks (EN 1303);
-- Padlocks and padlock fittings (EN 12320);
-- Mechanically operated push-button locksets (BS 8607);
-- Emergency exit devices operated by a lever handle or push pad, for use on escape routes and panic exit devices operated by a horizontal bar, for use on escape routes (EN 179, EN 1125);
- Electromechanical building hardware products:
-- Mechatronic cylinders (EN 15684);
-- Mechatronic padlocks (EN 16864);
-- Mechatronic door furniture (EN 16867);
-- Electromechanically operated locks and striking plates (EN 14846);
-- Electrically controlled exit systems for use on escape routes (EN 13637).
This document complements the core rules for the product category of construction products as defined in the European standard EN 15804:2012+A2:2019.
NOTE The assessment of social and economic performances at product level is not covered by this document.
The core PCR:
- defines the parameters to be declared and the way in which they are collated and reported;
- describes which stages of a product’s life cycle are considered in the EPD and which processes are to be included in the life cycle stages;
- defines rules for the development of scenarios;
- includes the rules for calculating the Life Cycle Inventory and the Life Cycle Impact Assessment underlying the EPD, including the specification of the data quality to be applied;
- includes the rules for reporting the predetermined, environmental and health information that is not covered by Life Cycle Assessment (LCA) for the product, construction process(es) and construction service(s), as relevant;
- defines the conditions under which construction products can be compared based on the information provided by EPD.
For the EPD of construction services the same rules and requirements apply as for the EPD of construction products.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17814:2022(Main)
Building hardware - Master Key System data protection - Guidance
SIST-TS CEN/TS 17814:2022

This document specifies requirements and procedures to achieve and maintain protection of data and sensitive information related to mechanical Master Key Systems and other mechanical key systems where customer or application related data are being processed throughout the process of planning, production, installation, and maintenance.
The requirements and test methods for mechanical cylinder locks is covered by EN 1303.
Reference is made to EN 1303 and Annexes relating to Master Key Systems (MKS).
Requirements relating to the information security of key based and non-key based electronic cylinders are not covered.

  • Technical specification
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-16:2019/AC:2022(Corrigendum)
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 16: Hardware for Lift and Slide windows
SIST EN 13126-16:2019/AC:2022

This part of EN 13126 specifies requirements and test methods for durability, strength, security and function of hardware for Lift and Slide windows and door height windows in accordance with common application as shown in informative Annex C, regardless of whether the hardware enables an additional tilt position.
NOTE 1   This document is also applicable to hardware systems, whereby the sash itself is not lifted but a gasket mechanism is moved.
NOTE 2   This document is also applicable to hardware systems, whereby the sash itself is not lifted but the sash is being moved parallel to the plane of the frame.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-1:2022(Main)
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 1: Requirements common to all types of hardware
SIST EN 13126-1:2022

This document specifies performance requirements for the strength and durability of hardware for the operation of movable sashes of windows and door height windows including requirements and test methods common to all hardware.
This document is applicable to the hardware suitable for windows and door height windows in Table 1, whatever the material used for the construction of the window.
Table 1 - Window opening-types
This document does not apply to the following:
—   fusible links;
—   hardware for lifting side-hung windows;
—   fixing devices that are used to assemble or install a fixed window;
—   devices that are used for the permanent fixing of a complete window into a building structure;
—   mechanisms for the pneumatic or hydraulic remote operation of windows;
—   single axis hinges (other than those, which provide a pivot-function for windows);
—   single axis hinges as covered in EN 1935;
—   hardware for sliding doors and folding doors as covered in EN 1527;
—   door and window bolts as covered in EN 12051.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-13:2022(Main)
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 13: Sash balances
SIST EN 13126-13:2022

This document specifies requirements and test methods for durability, strength, security and function of sash balances.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-4:2022(Main)
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 4: Espagnolettes
SIST EN 13126-4:2022

This document specifies requirements and test methods for durability, strength, security and function of espagnolettes and their striker plates for use on windows and door height windows.
Espagnolettes are defined as a locking mechanism for windows and door height windows that usually have a maximum handle movement of 90°.
This document does not include door bolts within the scope of EN 12051, or locks with latch and/or dead bolt within the scope of EN 12209 or multi-point locks within the scope of prEN 15685.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13126-14:2022(Main)
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 14: Sash fasteners
SIST EN 13126-14:2022

This document specifies requirements and test methods for durability, strength, security, and function of sash fasteners for windows and door height windows.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day