FprEN ISO 11118
(Main)Gas cylinders - Non-refillable metallic gas cylinders - Specification and test methods (ISO/FDIS 11118:2024)
Gas cylinders - Non-refillable metallic gas cylinders - Specification and test methods (ISO/FDIS 11118:2024)
ISO 11118:2015 specifies minimum requirements for the material, design, inspections, construction and workmanship, manufacturing processes, and tests at manufacture of non-refillable metallic gas cylinders of welded, brazed, or seamless construction for compressed and liquefied gases including the requirements for their non-refillable sealing devices and their methods of testing.
NOTE The specific gases permitted in cylinders constructed to this International Standard can be limited by national or international requirements.
This International Standard is applicable to cylinders where
a) the test pressure does not exceed 250 bar (i.e. ph ≤ 250 bar) for liquefied gases and 450 bar for compressed gases;
b) the product of the test pressure and the water capacity does not exceed 1 000 bar·litres (i.e. ph V ≤ 1 000 bar L);
c) the test pressure exceeds 45 bar and the water capacity does not exceed 5 l (i.e. for ph > 45 bar, then V ≤ 5 l).
Gasflaschen - Metallische Einwegflaschen - Spezifikationen und Prüfverfahren (ISO/FDIS 11118:2024)
Dieses Dokument legt Anforderungen an Werkstoff, Auslegung, Inspektionen, Bau und Ausführung, Herstellungsprozesse und Fertigungsprüfungen von geschweißten, hartgelöteten oder nahtlosen nicht wiederbefüllbaren metallischen Gasflaschen fest. Dieses Dokument legt auch die Anforderungen an nicht zur Wiederbefüllung geeignete Dichteinrichtungen und die zugehörigen Prüfverfahren fest. Sie ist anwendbar für nicht wiederbefüllbare metallische Gasflaschen für verdichtete und verflüssigte Gase.
ANMERKUNG Die spezifischen Gase, welche in nach diesem Dokument konstruierte Flaschen gefüllt werden dürfen, können durch nationale oder internationale Anforderungen begrenzt sein.
Dieses Dokument gilt für Flaschen, bei denen:
a) der Prüfdruck bei verflüssigten Gasen 250 bar (d. h. ph ≤ 250 bar) und bei verdichteten Gasen 450 bar nicht überschreitet; oder
b) das Produkt aus Prüfdruck und Fassungsraum 1 000 bar l (d. h. ph V ≤ 1 000 bar l) nicht überschreitet; oder
c) der Prüfdruck 45 bar überschreitet und der Fassungsraum 5 l nicht überschreitet (d. h. bei ph > 45 bar gilt V ≤ 5 l).
Bouteilles à gaz - Bouteilles à gaz métalliques non rechargeables -Spécifications et méthodes d'essai (ISO/FDIS 11118:2024)
ISO 11118:2015 spécifie les exigences minimales applicables aux matériaux, à la conception, aux contrôles, à la fabrication et à la qualité d'exécution ainsi qu'aux procédés de fabrication et aux essais chez le fabricant de bouteilles à gaz métalliques non rechargeables, soudées, brasées ou sans soudure, utilisées pour les gaz comprimés et liquéfiés, y compris les exigences pour leurs dispositifs d'étanchéité non réutilisables et leur méthode d'essai.
NOTE Les gaz spécifiques autorisés pour les bouteilles non rechargeables construites en conformité avec la présente Norme internationale peuvent être limités par des exigences nationales ou internationales.
La présente Norme internationale est applicable aux bouteilles non rechargeables dont:
a) la pression d'épreuve ne dépasse pas 250 bar (c'est-à-dire ph ≤ 250 bar) pour les gaz liquéfiés et 450 bar pour les gaz comprimés;
b) le produit de la pression d'épreuve par la contenance en eau ne dépasse pas 1 000 bar·litres (soit ph V ≤ 1 000 bar l);
c) la pression d'épreuve dépasse 45 bar et la contenance en eau ne dépasse pas 5 l (c'est-à-dire que pour ph > 45 bar, alors V ≤ 5 l).
Plinske jeklenke - Kovinske plinske jeklenke za enkratno polnitev - Specifikacija in preskusne metode (ISO/FDIS 11118:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 11118:2024
01-februar-2024
Plinske jeklenke - Kovinske plinske jeklenke za enkratno polnitev - Specifikacija in
preskusne metode (ISO/DIS 11118:2023)
Gas cylinders - Non-refillable metallic gas cylinders - Specification and test methods
(ISO/DIS 11118:2023)
Gasflaschen - Metallische Einwegflaschen - Spezifikationen und Prüfverfahren (ISO/DIS
11118:2023)
Bouteilles à gaz - Bouteilles à gaz métalliques non rechargeables - Spécifications et
méthodes d'essai (ISO/DIS 11118:2023)
Ta slovenski standard je istoveten z: prEN ISO 11118
ICS:
23.020.35 Plinske jeklenke Gas cylinders
oSIST prEN ISO 11118:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 11118:2024
oSIST prEN ISO 11118:2024
DRAFT INTERNATIONAL STANDARD
ISO/DIS 11118
ISO/TC 58/SC 3 Secretariat: BSI
Voting begins on: Voting terminates on:
2023-12-27 2024-03-20
Gas cylinders — Non-refillable metallic gas cylinders —
Specification and test methods
Bouteilles à gaz — Bouteilles à gaz métalliques non rechargeables — Spécifications et méthodes d'essai
ICS: 23.020.35
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 11118:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 11118:2024
ISO/DIS 11118:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 11118
ISO/TC 58/SC 3 Secretariat: BSI
Voting begins on: Voting terminates on:
Gas cylinders — Non-refillable metallic gas cylinders —
Specification and test methods
Bouteilles à gaz — Bouteilles à gaz métalliques non rechargeables — Spécifications et méthodes d'essai
ICS: 23.020.35
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 11118:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 11118:2024
ISO/DIS 11118:2023(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols . 3
5 Materials . 4
5.1 General requirements . 4
5.2 Material types . 4
5.2.1 Carbon and low-alloy steels . . 4
5.2.2 Aluminium and aluminium alloy . 5
5.2.3 Austenitic stainless steels . 5
5.3 Chemical compositions . 5
5.3.1 Carbon and low-alloy steels . . 5
5.3.2 Aluminium and aluminium alloys. 6
6 Inspection and testing .6
7 Design . 6
7.1 General requirements . 6
7.2 Calculation of pressure containing parts . 7
7.3 Design drawings . 7
8 Construction and workmanship .8
8.1 Construction . 8
8.1.1 Types of construction of cylinder shell . 8
8.1.2 Cylinder non-refillability.12
8.1.3 Pressure relief devices .12
8.2 Workmanship . 12
9 Type approval procedure .12
9.1 General requirements . 12
9.2 Prototype tests . .13
9.2.1 General .13
9.2.2 Material tests . 13
9.2.3 Tensile tests . 14
9.2.4 Burst tests .15
9.2.5 Drop tests . 16
9.2.6 Dimension checks . 17
9.2.7 Valve to cylinder interface test . 18
9.3 Design type approval . 18
10 Batch tests . .18
10.1 General requirements . 18
10.2 Failure to meet test requirements . 18
11 Tests on every cylinder .18
11.1 Visual inspection . 18
11.2 Proof pressure test . 19
11.3 Leak testing . 19
11.4 Rejection criteria . 19
11.5 Repairs . 19
12 Markings .19
12.1 General . 19
12.2 Manufacturing and operational markings . 19
iii
oSIST prEN ISO 11118:2024
ISO/DIS 11118:2023(E)
12.3 Other markings .20
13 Test reports and certificate of conformance .20
Annex A (normative) Non-refillable sealing devices — Specifications and prototype testing .21
Annex B (informative) Type approval certificate .27
Annex C (informative) Certificate of conformance .29
Annex D (informative) Yield point elongation (YPE) .31
Bibliography .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.