EN ISO 11118:2015/A1:2020

SLOVENSKI STANDARD
01-junij-2020
Plinske jeklenke - Kovinske plinske jeklenke za enkratno polnitev - Specifikacija in
preskusne metode - Dopolnilo A1 (ISO 11118:2015/Amd 1:2019)
Gas cylinders - Non-refillable metallic gas cylinders - Specification and test methods -
Amendment 1 (ISO 11118:2015/Amd 1:2019)
Gasflaschen - Metallische Einwegflaschen - Spezifikationen und Prüfverfahren -
Änderung 1 (ISO 11118:2015/Amd 1:2019)
Bouteilles à gaz - Bouteilles à gaz métalliques non rechargeables - Spécifications et
méthodes d'essai - Amendement 1 (ISO 11118:2015/Amd 1:2019)
Ta slovenski standard je istoveten z: EN ISO 11118:2015/A1:2020
ICS:
23.020.35 Plinske jeklenke Gas cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 11118:2015/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2020
EUROPÄISCHE NORM
ICS 23.020.35
English Version
Gas cylinders - Non-refillable metallic gas cylinders -
Specification and test methods - Amendment 1 (ISO
11118:2015/Amd 1:2019)
Bouteilles à gaz - Bouteilles à gaz métalliques non Gasflaschen - Metallische Einwegflaschen -
rechargeables - Spécifications et méthodes d'essai - Spezifikationen und Prüfverfahren - Änderung 1 (ISO
Amendement 1 (ISO 11118:2015/Amd 1:2019) 11118:2015/Amd 1:2019)
This amendment A1 modifies the European Standard EN ISO 11118:2015; it was approved by CEN on 21 October 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11118:2015/A1:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 11118:2015/A1:2020) has been prepared by Technical Committee ISO/TC 58
"Gas cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This Amendment to the European Standard EN ISO 11118:2015 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by October 2020,
and conflicting national standards shall be withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11118:2015/Amd 1:2019 has been approved by CEN as EN ISO 11118:2015/A1:2020
without any modification.
INTERNATIONAL ISO
STANDARD 11118
Second edition
2015-09-15
AMENDMENT 1
2019-10
Gas cylinders — Non-refillable
metallic gas cylinders — Specification
and test methods
AMENDMENT 1
Bouteilles à gaz — Bouteilles à gaz métalliques non rechargeables —
Spécifications et méthodes d'essai
AMENDEMENT 1
Reference number
ISO 11118:2015/Amd.1:2019(E)
©
ISO 2019
ISO 11118:2015/Amd.1:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 11118:2015/Amd.1:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 3,
Cylinder design.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
ISO 11118:2015/Amd.1:2019(E)
Gas cylinders — Non-refillable metallic gas cylinders —
Specification and test methods
AMENDMENT 1
Normative references
Add the following new reference:
ISO 14732, Welding personnel — Qualification testing of weld
...