EN ISO 15874-3:2013/A2:2021

SLOVENSKI STANDARD
SIST EN ISO 15874-3:2013/A2:2021
01-december-2021
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo -
Polipropilen (PP) - 3. del: Fitingi - Dopolnilo A2 (ISO 15874-3:2013/Amd 2:2021)
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3:
Fittings - Amendment 2 (ISO 15874-3:2013/Amd 2:2021)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polypropylen
(PP) - Teil 3: Formstücke - Änderung 2 (ISO 15874-3:2013/Amd 2:2021)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Polypropylène (PP) - Partie 3: Raccords - Amendement 2 (ISO 15874-3:2013/Amd
2:2021)
Ta slovenski standard je istoveten z: EN ISO 15874-3:2013/A2:2021
ICS:
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 15874-3:2013/A2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 15874-3:2013/A2:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 15874-3:2013/A2:2021


EN ISO 15874-3:2013/A2
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2021
EUROPÄISCHE NORM
ICS 23.040.45; 91.140.60
English Version

Plastics piping systems for hot and cold water installations
- Polypropylene (PP) - Part 3: Fittings - Amendment 2 (ISO
15874-3:2013/Amd 2:2021)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Polypropylène Kaltwasserinstallation - Polypropylen (PP) - Teil 3:
(PP) - Partie 3: Raccords - Amendement 2 (ISO 15874- Formstücke - Änderung 2 (ISO 15874-3:2013/Amd
3:2013/Amd 2:2021) 2:2021)
This amendment A2 modifies the European Standard 2776471; it was approved by CEN on 1 October 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15874-3:2013/A2:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 15874-3:2013/A2:2021
EN ISO 15874-3:2013/A2:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 15874-3:2013/A2:2021
EN ISO 15874-3:2013/A2:2021 (E)
European foreword
This document (EN ISO 15874-3:2013/A2:2021) has been prepared by Technical Committee ISO/TC
138 "Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical
Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held
by NEN.
This Amendment to the European Standard EN ISO 15874-3:2013 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by April 2022, and
conflicting national standards shall be withdrawn at the latest by April 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, B
...