EN ISO 11199-2:2005

SLOVENSKI STANDARD
01-julij-2005
1DGRPHãþD
SIST EN ISO 11199-2:2000
3ULSRPRþNL]DKRMRNLVHXSUDYOMDMR]REHPDURNDPD=DKWHYHLQSUHVNXVQH
PHWRGHGHO5RODWRUML,62
Walking aids manipulated by both arms - Requirements and test methods - Part 2:
Rollators (ISO 11199-2:2005)
Gehhilfen für beidarmige Handhabung - Anforderungen und Prüfverfahren - Teil 2:
Rollatoren (ISO 11199-2:2005)
Aides a la marche manipulées avec les deux bras - Exigences et méthodes d'essai -
Partie 2: Déambulateurs (ISO 11199-2:2005)
Ta slovenski standard je istoveten z: EN ISO 11199-2:2005
ICS:
11.180.10 3ULSRPRþNLLQSULODJRGLWYH]D Aids and adaptation for
JLEDQMH moving
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11199-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2005
ICS 11.180.10 Supersedes EN ISO 11199-2:1999
English version
Walking aids manipulated by both arms - Requirements and test
methods - Part 2: Rollators (ISO 11199-2:2005)
Aides à la marche manipulées avec les deux bras - Gehhilfen für beidarmige Handhabung - Anforderungen und
Exigences et méthodes d'essai - Partie 2: Déambulateurs Prüfverfahren - Teil 2: Rollatoren (ISO 11199-2:2005)
(ISO 11199-2:2005)
This European Standard was approved by CEN on 14 April 2005.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11199-2:2005: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 11199-2:2005) has been prepared by Technical Committee ISO/TC
173 "Technical systems and aids for disabled or handicapped persons" in collaboration with
Technical Committee CEN/TC 293 "Technical aids for disabled persons", the secretariat of
which is held by SIS.
This document supersedes EN ISO 11199-2:1999.

This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by October 2005, and conflicting national
standards shall be withdrawn at the latest by October 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 11199-2:2005 has been approved by CEN as EN ISO 11199-2:2005 without
any modifications.
INTERNATIONAL ISO
STANDARD 11199-2
Second edition
2005-04-15
Walking aids manipulated by both
arms — Requirements and test
methods —
Part 2:
Rollators
Aides à la marche manipulées avec les deux bras — Exigences et
méthodes d'essai —
Partie 2: Déambulateurs
Reference number
ISO 11199-2:2005(E)
©
ISO 2005
ISO 11199-2:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved

ISO 11199-2:2005(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Requirements . 7
4.1 Manoeuvrability. 7
4.2 Stability . 7
4.3 Brakes . 7
4.4 Handgrip. 8
4.5 Leg section and tip . 8
4.6 Resting seat. 8
4.7 Mechanical durability. 8
4.8 Adjusting devices . 8
4.9 Folding mechanism . 9
4.10 Adjustment of handles . 9
4.11 Materials and finish. 9
5 Test methods. 9
5.1 General. 9
5.2 Sampling and inspection. 9
5.3 Forward-direction stability test . 10
5.4 Backward-direction stability test. 11
5.5 Sideway-direction stability test . 11
5.6 Accessory equipment. 12
5.7 Brake tests. 13
5.8 Handgrip test . 14
5.9 Rubber tip test. 14
5.10 Resting seat test . 14
5.11 Static loading test . 14
5.12 Fatigue test . 16
5.13 Final inspection. 17
6 Information supplied by the manufacturer. 17
6.1 General. 17
6.2 Information marked on the product and / or accessories . 17
6.3 Documentation . 18
7 Test report. 18
Annex A (informative) Recommendations . 19
Bibliography . 22

ISO 11199-2:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11199-2 was prepared by Technical Committee ISO/TC 173, Assistive products for persons with disability.
This second edition cancels and replaces the first edition (ISO 11199-2:1999), which has been technically
revised.
ISO 11199 consists of the following parts, under the general title Walking aids manipulated by both arms —
Requirements and test methods:
 Part 1: Walking frames
 Part 2: Rollators
 Part 3: Walking tables
iv © ISO 2005 – All rights reserved

INTERNATIONAL STANDARD ISO 11199-2:2005(E)

Walking aids manipulated by both arms — Requirements
and test methods —
Part 2:
Rollators
1 Scope
This part of ISO 11199 specifies requirements and methods of testing the static stability braking capabilities,
static strength and fatigue of rollators being used as walking aids with wheels, manipulated by the hands,
without accessories, unless specified in the particular test procedure. This part of ISO 11199 also gives
requirements relating to safety, ergonomics, performance, and information supplied by the manufacturer
including marking and labelling.
The requirements and tests are based on every-day usage of rollators as walking aids, for a maximum user
mass as specified by the manufacturer. This part of ISO 11199 includes rollators specified for a user mass of
no less than 35 kg.
This part of ISO 11199 is not applicable to rollators with horizontal forearm supports, classified as walking
tables, for which ISO 11199-3 is applicable.
N
...