EN ISO 10535:2021

SLOVENSKI STANDARD
01-januar-2022
Nadomešča:
SIST EN ISO 10535:2007
Tehnični pripomočki - Dvigala za prestavljanje oseb - Zahteve in preskusne
metode (ISO 10535:2021)
Assistive products - Hoists for the transfer of persons - Requirements and test methods
(ISO 10535:2021)
Lifter zum Transfer von Menschen mit Behinderungen - Anforderungen und
Prüfverfahren (ISO 10535:2021)
Produits d'assistance - Lève-personnes pour transférer des personnes - Exigences et
méthodes d'essais (ISO 10535:2021)
Ta slovenski standard je istoveten z: EN ISO 10535:2021
ICS:
11.180.10 Pripomočki in prilagoditve za Aids and adaptation for
gibanje moving
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 10535
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2021
EUROPÄISCHE NORM
ICS 11.180.10 Supersedes EN ISO 10535:2006
English Version
Assistive products - Hoists for the transfer of persons -
Requirements and test methods (ISO 10535:2021)
Produits d'assistance - Lève-personnes pour transférer Lifter zum Transfer von Menschen mit Behinderungen
des personnes - Exigences et méthodes d'essais (ISO - Anforderungen und Prüfverfahren (ISO 10535:2021)
10535:2021)
This European Standard was approved by CEN on 31 August 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10535:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 10535:2021) has been prepared by Technical Committee ISO/TC 173 "Assistive
products" in collaboration with Technical Committee CEN/TC 293 “Assistive products and accessibility”
the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2022, and conflicting national standards shall be
withdrawn at the latest by May 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10535:2006.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 10535:2021 has been approved by CEN as EN ISO 10535:2021 without any modification.

INTERNATIONAL ISO
STANDARD 10535
Third edition
2021-10
Assistive products — Hoists for the
transfer of persons — Requirements
and test methods
Produits d'assistance — Lève-personnes pour transférer des
personnes — Exigences et méthodes d'essais
Reference number
ISO 10535:2021(E)
ISO 10535:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 10535:2021(E)
Contents Page
Foreword .vii
Introduction .viii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 General requirements and test methods . 8
4.1 General requirements . 8
4.1.1 Risk management . 8
4.1.2 Ergonomic factors . 8
4.1.3 Noise and vibration . 8
4.1.4 Safety of moving and folding parts . 9
4.1.5 Prevention of traps for parts of the human body . 10
4.1.6 V-shaped openings . 11
4.2 General test methods . 11
4.2.1 Test conditions . 11
4.2.2 Apparatus . 11
4.2.3 Permissible errors of test equipment .12
4.2.4 Test report .12
4.2.5 Safety and performance requirements . 16
4.2.6 Test methods for general safety requirements . 19
4.3 Requirements for body-support units . 22
4.4 Central suspension point .22
4.4.1 Requirements for central suspension point . 22
4.4.2 Test method for the central suspension point .22
4.5 Spreader bar .22
4.5.1 Requirements for spreader bar . 22
4.5.2 Test methods for the spreader bar . 23
4.6 Performance . 23
4.6.1 Requirements for performance . 23
4.6.2 Test methods for performance . 23
4.7 Rate of movements of the hoist . 24
4.7.1 Requirements for rate of lifting and lowering . 24
4.7.2 Test methods for rate of lifting and lowering . 24
4.7.3 Requirements for rate of powered horizontal movement . 24
4.7.4 Test methods for rate of powered horizontal movement . 24
4.8 Operating forces/torques . 24
4.8.1 Requirements for operating forces/torques . . 24
4.8.2 Test methods for operating forces/torques . 25
4.9 Durability . 25
4.9.1 Requirements for durability . 25
4.9.2 Test methods for durability . 25
4.10 Hydraulic components . 27
4.10.1 Requirements for hydraulic components . 27
4.10.2 Test methods for hydraulic components .28
4.11 Pneumatic components .28
4.11.1 Requirements for pneumatic components .28
4.11.2 Test methods for pneumatic components .28
4.12 Machine washable hoists . 29
4.12.1 Requirements for machine washable hoists .29
4.12.2 Test methods for machine washable hoists . .29
4.13 Requirement for information supplied by the manufacturer .30
4.13.1 General .30
4.13.2 Instructions for use. 30
iii
ISO 10535:2021(E)
4.13.3 Labelling . 32
5 Mobile hoists — Specific requirements and test methods .37
5.1 General requirements . 37
5.2 Static strength . . 37
5.2.1 Requirements for static strength . 37
5.2.2 Test methods for static strength . 37
5.3 Static stability .38
5.3.1 Requirements for static stability .38
5.3.2 Test methods for static stability .38
5.4 Immobilizing device (brakes) .38
5.4.1 Requirements for immobilizing device (brakes) .38
5.4.2 Test methods for immobilizing device (brakes) .38
5.5 Moving forces . .39
5.5.1 Requirements for moving forces .39
5.5.2 Test methods for moving forces.39
5.6 Requirement for information supplied by the manufacturer .40
5.6.1 Pre-sale information .40
6 Mobile hoists for transferring a person in standing position— Specific requirements
and test methods.41
6.1 General requirements . 41
6.2 Static strength . . 41
6.2.1 Requirements for static strength . 41
6.2.2 Test method for static strength. 41
6.3 Static stability . 41
6.3.1 Requirements for static stability . 41
6.3.2 Test methods for static stability . 42
6.4 Immobilizing device (brakes) . 43
6.4.1 Requirements for immobilizing device (brakes) . 43
6.4.2 Test methods for immobilizing device (brakes) . 43
6.5 Moving forces . . 43
6.5.1 Requirements for moving forces . 43
6.5.2 Test methods for moving forces. 43
6.6 Durability . 43
6.6.1 Requirements for durability . 43
6.6.2 Test methods for durability . 43
6.7 Requirement for information supplied by the manufacturer .44
6.7.1 Pre-sale information .44
7 Stationary hoists — Specific requirements and test methods . 44
7.1 General requirements .44
7.2 Specific safety requirements . 45
7.2.1 Requirements for specific safety requirements . 45
7.2.2 Test methods for specific safety requirements . 45
7.3 Static strength (free-standing stationary hoists only) . 45
7.3.1 Requirements for static strength (free-standing stationary hoists only) . 45
7.3.2 Test methods for static strength (free-standing stationary hoists only) . 45
7.4 Static stability (free-standing stationary hoists only) .46
7.4.1 Requirements for static stability (free-standing stationary hoists only) .46
7.4.2 Test methods for static stability (free-standing stationary hoists only) .46
7.5 Static strength for all other stationary hoists . 47
7.5.1 Requirements for static strength for all other stationary hoists . 47
7.5.2 Test methods for static strength for all other stationary hoists . 47
7.6 Requirement for information supplied by the manufacturer . 47
7.6.1 User information . 47
8 Non-rigid body-support units — Specific requirements and test methods .47
8.1 General requirements . 47
8.2 Requirements for material and seams of the non-rigid body-support unit . 47
iv
ISO 10535:2021(E)
8.3 Test methods for non-rigid body-support unit .48
8.3.1 Test methods for non-rigid body-support unit designed to be laundered .48
8.3.2 Test method for durability for non-rigid body-support unit .48
8.4 Requirement for information supplied by the manufacturer .48
8.4.1 Pre-sale information .48
8.4.2 User information .48
8.4.3 Labelling .49
9 Rigid body-support units — Specific requirements and test methods .49
9.1 General requirements .49
9.2 Requirements for backrest .50
9.3 Requirements and test methods for durability .50
9.4 Requirement for information supplied by the manufacturer .50
9.4.1 User information .50
9.4.2 Labelling . 50
10 Bathtub hoists — Specific requirements and test methods .51
10.1 General requirements . 51
10.1.1 General . 51
10.1.2 Risk analysis . 51
10.1.3 Ergonomic factors . 51
10.1.4 Noise . 51
10.1.5 Safety of moving and folding parts . 51
10.1.6 Prevention of traps for parts of the human body . 51
10.1.7 V-shaped openings . 51
10.2 General test methods . 52
10.2.1 Test conditions . 52
10.2.2 Test equipment . 52
10.2.3 Permissible errors of test equipment . 52
10.2.4 Test report . 52
10.3 Safety requirements . 52
10.3.1 General safety requirements . 52
10.3.2 Test methods for general safety requirements . 52
10.4 Body-support units . 53
10.5 Spreader bar .53
10.6 Performance .53
10.7 Rate of movements of the hoist . 53
10.8 Operating forces/torques .53
10.9 Durability . 53
10.9.1 Requirements for durability . 53
10.9.2 Test methods for durability . 53
10.10 Static strength and stability .54
10.10.1 Requirements for static strength and stability .54
10.10.2 .
Test methods for static strength and stability .54
10.11 Hydraulic components .54
10.12 Pneumatic components . 55
10.13 Specific safety requirements . 55
10.13.1 Requirements for specific safety requirements . 55
10.13.2 .
Test methods for specific safety requirements . . 55
10.14 Non-rigid body-support units .55
10.15 Rigid body-support units — Requirements . 55
10.16 Requirement for information supplied by the manufacturer . 55
10.16.1 General .55
10.16.2 .
Instructions for use.55
10.16.3 .
Labelling . 55
v
ISO 10535:2021(E)
Annex A (informative) Rationale for specific safety requirements .56
Annex B (informative) Periodic inspection and maintenance .58
Annex C (informative) Compatibility of hoist/spreader bar/body-support units .61
Annex D (informative) Guidelines for colour coding for size of non-rigid body-support units .74
Bibliography .75
vi
ISO 10535:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 173, Assistive products, in collaboration
with the European Committee for Standardization (CEN) Technical Committee CEN/TC 293, Assistive
products and accessibility, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 10535:2006), which has been technically
revised.
The main changes are as follows:
— aspects on hoists with robotic features has been included;
— guidelines regarding compatibility of hoists/body-support units have been included;
— the informative annex on Inspection has been further developed;
— lowering of minimum capacity of a mobile hoist from 120 kg to 100 kg;
— requirement of emergency lowering device for mobile hoist and standing/raising hoists has been
included.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
vii
ISO 10535:2021(E)
Introduction
It appears from studies that the nursing and caring profession involves many physically burdening
factors in the caring for and nursing of persons with disabilities. A hoist offers a safe means of
supportive lifting and moving, either assisted or independently.
This document specifies requirements and test methods that are relevant to hoists for the transfer of
persons with disabilities. This document addresses further needs in terms of providing safety for both
the person with a disability and the attendant, while taking into account the potential new development
within robotic technology on hoist solutions.
viii
INTERNATIONAL STANDARD ISO 10535:2021(E)
Assistive products — Hoists for the transfer of persons —
Requirements and test methods
1 Scope
This document specifies requirements and test methods for hoists and body-support units intended for
the transfer of persons with disabilities. The document applies to the following products classified in
1)
ISO 9999:— .
— 12 36 03 Mobile hoists for transferring a person in sitting position with sling seats;
— 12 36 04 Mobile hoists for transferring a person in standing position;
— 12 36 06 Mobile hoists for transferring a person in sitting position with solid seats;
— 12 36 09 Mobile hoists for transferring a person in lying position;
— 12 36 12 Stationary hoists fixed to walls, floor or ceiling;
— 12 36 15 Stationary hoists fixed to, or mounted in or on, another product;
— 12 36 18 Stationary free-standing hoists;
— 12 36 21 Body-support units for hoists.
This document covers different types of mobile and stationary hoists. Some of the requirements and
test methods are general and others are only valid for specific product types.
Annexes A, B and C provide general recommendations.
This document does not apply to devices that transport persons between two levels (floors) of a
building.
It does not include methods for the determination of ageing or corrosion of such hoists and units.
It does not include methods to qualify individual units prior to use.
The requirements of this document are formulated with regard to the needs of both the persons being
hoisted and the attendant using the hoist.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3746, Acoustics — Determination of sound power levels and sound energy levels of noise sources using
sound pressure — Survey method using an enveloping measurement surface over a reflecting plane
ISO 3758, Textiles — Care labelling code using symbols
ISO 10993-1, Biological evaluation of medical devices — Part 1: Evaluation and testing within a risk
management process
ISO 14971, Medical devices — Application of risk management to medical devices
1) Under preparation. Stage at the time of publication: ISO/FDIS 9999:2021.
ISO 10535:2021(E)
ISO 15223-1:2021, Medical devices — Symbols to be used with information to be supplied by the
manufacturer — Part 1: General requirements
ISO 20417, Medical devices — Information to be supplied by the manufacturer
IEC 60204-1, Safety of machinery - Electrical equipment of machines - Part 1: General requirements
IEC 60529, Degrees of protection provided by enclosures (IP Code)
IEC 60601-1:2005+AMD1: 2012+ AMD2: 2020, Medical electrical equipment — Part 1: General requirements
for basic safety and essential performance
IEC 60601-1-2:2014+AMD1: 2020, Medical electrical equipment — Part 1-2: General requirements for
safety — Collateral standard: Electromagnetic compatibility — Requirements and tests
IEC 60601-1-11, Medical electrical equipment — Part 1-11: General requirements for basic safety and
essential performance - Collateral Standard: Requirements for medical electrical equipment and medical
electrical systems used in the home healthcare environment
IEC 61672-1, Electroacoustics — Sound level meters — Part 1: Specifications
EN 853, Rubber hoses and hose assemblies — Wire braid reinforced hydraulic type — Specification
EN 854, Rubber hoses and hose assemblies — Textile reinforced hydraulic type — Specification
EN 1021-1, Furniture — Assessment of the ignitability of upholstered furniture — Part 1: Ignition source
smouldering cigarette
EN 1021-2, Furniture — Assessment of the ignitability of upholstered furniture — Part 2: Ignition source
match flame equivalent
EN 13480-3:2017, Metallic industrial piping — Part 3: Design and calculation
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
adverse condition
condition in which failure is most likely to occur
3.2
attendant
person who operates the hoist if not the person with disability (3.36)
3.3
backrest
part of the body-support unit (3.6) that provides support to the back of the person being lifted in a hoist
3.4
backwards
180° to the forwards (3.20) direction of travel
ISO 10535:2021(E)
3.5
bathtub hoist
equipment specifically designed to be used in or adjacent to a bathtub for transferring by lifting and
moving a person in an area limited by the system
3.6
body-support unit
device for providing support to a person being lifted, transferred or moved in a hoist, with its associated
attachment structure
EXAMPLE A sling, seat or stretcher.
3.7
ceiling hoist
equipment for transferring by lifting and moving a person in a specific location by an overhead mounted
system fixed to the ceiling or wall(s), including the tracking system
3.8
central suspension point
CSP
reference point on the hoist to be used for measurements
Note 1 to entry: This point may be a connecting point.
3.9
connecting point
part to which the body-support unit (3.6) attaches
3.10
control device
part or parts of the hoist that operate the lifting and lowering
...