EN ISO 14096-2:2020

SLOVENSKI STANDARD
01-junij-2020
Nadomešča:
SIST EN 14096-2:2004
Neporušitvene preiskave - Kvalificiranje sistemov za digitaliziranje radiogramov -
2. del: Minimalne zahteve (ISO 14096-2:2005)
Non-destructive testing - Qualification of radiographic film digitisation systems - Part 2:
Minimum requirements (ISO 14096-2:2005)
Zerstörungsfreie Prüfung - Qualifizierung von Röntgenfilm-Digitalisierungssystemen -
Teil 2: Mindestanforderungen (ISO 14096-2:2005)
Essais non destructifs - Qualification des systèmes de numérisation des films
radiographiques - Partie 2: Exigences minimales (ISO 14096-2:2005)
Ta slovenski standard je istoveten z: EN ISO 14096-2:2020
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
37.040.25 Radiografski filmi Radiographic films
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 14096-2
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2020
EUROPÄISCHE NORM
ICS 37.040.25 Supersedes EN 14096-2:2003
English Version
Non-destructive testing - Qualification of radiographic film
digitisation systems - Part 2: Minimum requirements (ISO
14096-2:2005)
Essais non destructifs - Qualification des systèmes de Zerstörungsfreie Prüfung - Qualifizierung von
numérisation des films radiographiques - Partie 2: Röntgenfilm-Digitalisierungssystemen - Teil 2:
Exigences minimales (ISO 14096-2:2005) Mindestanforderungen (ISO 14096-2:2005)
This European Standard was approved by CEN on 6 January 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14096-2:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 14096-2:2005 has been prepared by Technical Committee ISO/TC 135 "Non-destructive
testing” of the International Organization for Standardization (ISO) and has been taken over as
which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2020, and conflicting national standards
shall be withdrawn at the latest by September 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14096-2:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 14096-2:2005 has been approved by CEN as EN ISO 14096-2:2020 without any
modification.
INTERNATIONAL ISO
STANDARD 14096-2
First edition
2005-06-15
Non-destructive testing — Qualification
of radiographic film digitisation
systems —
Part 2:
Minimum requirements
Essais non destructifs — Qualification des systèmes de numérisation
des films radiographiques —
Partie 2: Exigences minimales
Reference number
ISO 14096-2:2005(E)
©
ISO 2005
ISO 14096-2:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved

ISO 14096-2:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14096-2 was prepared by the European Committee for Standardization (CEN) (as EN 14096-2:2003) and
was adopted, under a special “fast-track procedure”, by Technical Committee ISO/TC 135, Non-destructive
testing, Subcommittee SC 5, Radiation methods, in parallel with its approval by the ISO member bodies.
ISO 14096 consists of the following parts, under the general title Non-destructive testing — Qualification of
radiographic film digitisation systems:
 Part 1: Definitions, quantitative measurements of image quality parameters, standard reference film and
qualitative control
 Part 2: Minimum requirements
ISO 14096-2:2005(E)
EN 14096-2:2003 (E)
Page
Contents
Foreword .3
Introduction.4
1 Scope.5

2 Normative references .5
3 Terms and definitions.5
4 Digitisation quality classes.7
5 Minimum requirements for film digitisation quality classes .7
iv © ISO 2005 – All rights reserved

ISO 14096-2:2005(E)
EN 14096-2:2003 (E)
Foreword
This document (EN 14096-2:2003) has been prepared by Technical Committee CEN/TC 138, "Non-destructive
testing", the secretariat of which is held by AFNOR.
This European Standard shall be given the sta
...