EN 15719:2009

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.GLUDQLKSanitärausstattungsgegenstände - Badewannen, hergestellt aus schlagzäh-modifizierten coextrudierten ABS/Acrylplatten - Anforderungen und PrüfverfahrenAppareils sanitaires - Baignoires en feuilles coextrudées ABS/Acrylique modifié choc - Prescriptions et méthodes d'essaiSanitary appliances - Baths made from impact modified coextruded ABS/acrylic sheets - Requirements and test methods91.140.70Sanitarne napraveSanitary installationsICS:Ta slovenski standard je istoveten z:EN 15719:2009SIST EN 15719:2010en,fr,de01-marec-2010SIST EN 15719:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15719
December 2009 ICS 91.140.70 English Version
Sanitary appliances - Baths made from impact modified coextruded ABS/acrylic sheets - Requirements and test methods Appareils sanitaires - Baignoires en feuilles coextrudées ABS/acrylique modifié choc - Prescriptions et méthodes d'essai
Sanitärausstattungsgegenstände - Badewannen, hergestellt aus schlagzäh-modifizierten coextrudierten ABS/Acrylplatten - Anforderungen und Prüfverfahren This European Standard was approved by CEN on 7 November 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15719:2009: ESIST EN 15719:2010

Bath test methods.9A.1 Sequence of tests .9A.2 Geometric deviations .9A.2.1 Test apparatus .9A.2.2 Squaring .9A.2.3 Straightness of the rim side . 10A.2.4 Straightness of the bottom edge of the rim . 11A.2.5 Flatness of the top surface of the rim. 12A.3 Resistance to temperature change . 13A.3.1 Test apparatus . 13A.3.2 Procedure . 13A.4 Resistance to impact . 14A.4.1 Test apparatus . 14A.4.2 Test procedure . 15A.5 Determination of deflections . 15A.5.1 General . 15A.5.2 Test apparatus . 15A.5.3 Installation methods . 16A.5.4 Preloading . 18A.5.5 Deflection test 1 – Deflection of the rim and the bottom due to a load on the bottom . 18A.5.6 Deflection test 2 – Deflection of the bottom and rim due to a load on the bottom . 19SIST EN 15719:2010

Geometric deviations 4.10.1 General The straight sides or edges of the bath that might abut independent surroundings or supporting structures shall comply with the requirements of 4.10.2 to 4.10.4 and all baths shall comply with 4.10.5. These requirements are not applicable to sides or edges that are purposely designed as curves or slopes. 4.10.2 Squaring When tested in accordance with A.2.2 the deviation from square, ûq, shall be less than or equal to 5 mm. 4.10.3 Straightness of the rim sides When tested in accordance with A.2.3 the deviation from straightness of the rim sides, ûs, shall be less than or equal to 5 mm. SIST EN 15719:2010

Flatness of the top surface of the rim When tested in accordance with A.2.5 the deviation from flatness of the top surface of the rim, c, shall be less than or equal to 5 mm. 4.11 Bottom of the bath When the bath is installed in accordance with the manufacturer's instructions and the waste outlet hole is open, all water shall empty from the bath unless prevented by surface tension. 4.12 Resistance to temperature changes When tested in accordance with A.3 baths shall show no evidence of distortion or other defects that impair the appearance or functioning of the bath and any deflection shall be less than or equal to 4 mm. 4.13 Resistance to impact When tested in accordance with A.4 the bottom and the rim of the bath shall show no evidence of distortion or other defects that impair the appearance or functioning of the bath. 4.14
Permitted deflections When tested in accordance with A.5 the deflections shall be less than or equal to the values given in Table 1. Table 1 — Permitted deflections
Test method Maximum deflections a under load and permitted residual deflections for installation methods b mm a) b) c) d) e) A.5.5 ≤ 1 on the four free rims ≤ 2 on the bottom ≤ 1 on the three free rims ≤ 0,5 on the fixed rim ≤ 2 on the bottom ≤ 1 on the two free rims ≤ 0,5 on the two fixed rims ≤ 2 on the bottom ≤ 1 on the free rim ≤ 0,5 on the three fixed rims ≤ 2 on the bottom ≤ 0,5 on all rims ≤ 2 on the bottom A.5.6 ≤ 2 on the four free rims ≤ 3 on the bottom ≤ 2 on the three free rims ≤ 0,5 on the fixed rim ≤ 3 on the bottom ≤ 2 on the two free rims ≤ 0,5 on the two fixed rims ≤ 3 on the bottom ≤ 2 on the free rim ≤ 0,5 on the three fixed rims ≤ 3 on the bottom ≤ 0,5 on all rims ≤ 3 on the bottom A.5.7 ≤ 4 on the rim ≤ 0,3 residual ≤ 4 on the rim ≤ 0,3 residual ≤ 4 on the rim ≤ 0,3 residual ≤ 4 on the rim ≤ 0,3 residual Not applicable A.5.8 ≤ 4 on the rim ≤ 0,3 residual ≤ 4 on the rim ≤ 0,3 residual ≤ 4 on the rim ≤ 0,3 residual Not applicable Not applicable a Values in addition to any deflection of the test rig (see A.5.2). b See A.5.3. SIST EN 15719:2010
...