EN 10303:2015
(Main)Thin magnetic steel strip and sheet for use at medium frequencies
Thin magnetic steel strip and sheet for use at medium frequencies
This European Standard defines the grades of thin non-oriented magnetic steel strip and sheet in nominal thicknesses of 0,05 mm, 0,10 mm, 0,15 mm, 0,20 mm, 0,25 mm, 0,27 mm,0,30 mm and 0,35 mm, and of thin grain-oriented magnetic steel strip and sheet in nominal thicknesses of 0,05 mm, 0,10 mm, 0,15 mm and 0,18 mm. In particular, it gives general requirements, magnetic properties, geometric characteristics and tolerances and technological characteristics, as well as inspection procedure.
This European Standard applies to magnetic steel strip and sheet supplied in the finally annealed condition in coils and intended for the construction of magnetic circuits used at frequencies equal to or higher than 100 Hz.
Dünnes Elektroband und -blech aus Stahl zur Verwendung bei mittleren Frequenzen
Die vorliegende Europäische Norm enthält die Anforderungen an dünnes nichtkornorientiertes Elektroblech und -band der Nenndicken 0,05 mm; 0,10 mm; 0,15 mm; 0,20 mm; 0,25 mm; 0,27 mm; 0,30 mm und 0,35 mm sowie dünnes kornorientiertes Elektroblech und -band der Nenndicken 0,05 mm, 0,10 mm; 0,15 mm und 0,18 mm. Im Einzelnen sind die allgemeinen Anforderungen, die magnetischen Eigenschaften, die geometrischen Eigenschaften und Toleranzen, die technologischen Eigenschaften sowie die Prüfverfahren festgelegt.
Diese Europäische Norm gilt für Elektroblech und -band im schlussgeglühten Zustand in der Form von Rollen, das für die Herstellung magnetischer Kreise bei Frequenzen von 100 Hz und mehr bestimmt ist.
Bandes et tôles extra-minces en acier électrique pour utilisation à moyennes fréquences
La présente Norme européenne définit les nuances de tôles et bandes magnétiques extra-minces en acier à grains non orientés d'épaisseurs nominales 0,05 mm, 0,10 mm, 0,15 mm, 0,20 mm, 0,25 mm, 0,27 mm, 0,30 mm et 0,35 mm et de tôles et bandes magnétiques extra-minces en acier à grains orientés d'épaisseurs nominales 0,05 mm, 0,10 mm, 0,15 mm et 0,18 mm. Elle donne en particulier les prescriptions générales, les caractéristiques magnétiques, les caractéristiques géométriques et les tolérances et les caractéristiques technologiques ainsi que les conditions de contrôle.
La présente Norme européenne est applicable aux tôles et bandes magnétiques en acier livrées après recuit final, en bobines et destinées à la construction de circuits magnétiques utilisés pour des fréquences égales ou supérieures à 100 Hz.
Tanka magnetna jeklena pločevina in trakovi za uporabo pri srednjih frekvencah
Ta evropski standard določa vrste tankih neorientiranih magnetnih jeklenih pločevin in trakov z nazivnimi debelinami 0,05 mm, 0,10 mm, 0,15 mm, 0,20 mm, 0,25 mm in 0,30 mm ter tankih orientiranih magnetnih jeklenih pločevin in trakov z nazivnimi debelinami 0,05 mm, 0,10 mm, 0,15 mm. Posebej določa splošne zahteve, magnetne lastnosti, geometrijske lastnosti in tolerance, tehnološke lastnosti ter postopke pregledovanja.
Ta evropski standard se uporablja za magnetno jekleno pločevino in trakove, dobavljene v končnem žarjenem stanju v obliki tuljav, in je namenjen konstruiranju magnetnih krogov, uporabljenih na frekvencah, ki so enake ali večje od 100 Hz.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Dünnes Elektroblech und -band aus Stahl zur Verwendung bei mittleren FrequenzenTôles et bandes magnétiques extra-minces en acier pour utilisation à moyennes fréquencesThin magnetic steel sheet and strip for use at medium frequencies77.140.50SROL]GHONLFlat steel products and semi-products77.140.40Jekla s posebnimi magnetnimi lastnostmiSteels with special magnetic propertiesICS:Ta slovenski standard je istoveten z:EN 10303:2015SIST EN 10303:2016en,fr,de01-januar-2016SIST EN 10303:2016SLOVENSKI
STANDARDSIST EN 10303:20021DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10303
October
t r s w ICS
y yä s v rä v râ
y yä s v rä w r Supersedes EN
s r u r uã t r r sEnglish Version
Thin magnetic steel strip and sheet for use at medium frequencies Bandes et tôles extraæminces en acier électrique pour utilisation à moyennes fréquences
Dünnes Elektroband und æblech aus Stahl zur Verwendung bei mittleren Frequenzen This European Standard was approved by CEN on
t { August
t r s wä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s w CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s r u r uã t r s w ESIST EN 10303:2016
Minimum stacking factor for non-oriented coated products . 18 Annex B (informative)
Maximum specific total loss at 1,0T and 700 Hz and at 1,5T and 400Hz for non-oriented products . 19 Annex C (informative)
Density determination . 20 Annex D (informative)
Mechanical properties for non-oriented products . 21 Annex E (informative)
Changes to the previous version EN 10303:2001 . 22 Bibliography . 23
EN 10303:20
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.