iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

CEN ISO/TS 21432:2005/AC:2009

(Corrigendum)

Non-destructive testing - Standards test method for determining residual stresses by neutron diffraction (ISO 21432:2005/Cor 1:2008)

Non-destructive testing - Standards test method for determining residual stresses by neutron diffraction (ISO 21432:2005/Cor 1:2008)

ISO - Taking over of an ISO Technical Corrigendum

Zerstörungsfreie Prüfung - Standardprüfverfahren zur Bestimmung von Eigenspannungen durch Neutronenbeugung (ISO/TS 21432:2005/Cor 1:2008)

Essais non destructifs - Méthode normalisée de détermination des contraintes résiduelles par diffraction de neutrons (ISO 21432:2005/Cor 1:2008)

Neporušitveno preskušanje - Standardizirane preskusne metode za ugotavljanje zaostalih napetosti z uklonom nevtronskih žarkov (ISO 21432:2005/Cor 1:2008)

General Information

Status
Withdrawn
Publication Date
07-Apr-2009
Withdrawal Date
22-Sep-2020
ICS
19.100 - Non-destructive testing
Technical Committee
CEN/TC 138 - Non-destructive testing
Drafting Committee
CEN/TC 138 - Non-destructive testing
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
23-Sep-2020
Ref Project
SIST-TS CEN ISO/TS 21432:2005/AC:2009 - Non-destructive testing - Standards test method for determining residual stresses by neutron diffraction (ISO 21432:2005/Cor 1:2008)

Relations

Replaced By
EN ISO 21432:2020 - Non-destructive testing - Standard test method for determining residual stresses by neutron diffraction (ISO 21432:2019)
Effective Date
28-Oct-2020
Corrects
CEN ISO/TS 21432:2005 - Non-destructive testing - Standards test method for determining residual stresses by neutron diffraction (ISO 21432:2005)
Effective Date
22-Dec-2008

Buy Standard

TS CEN ISO/TS 21432:2005/AC:2009TS CEN ISO/TS 21432:2005/AC:2009
PreviousNext
Corrigendum
TS CEN ISO/TS 21432:2005/AC:2009
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Neporušitveno preskušanje - Standardizirane preskusne metode za ugotavljanje zaostalih napetosti z uklonom nevtronskih žarkov (ISO 21432:2005/Cor 1:2008)Zerstörungsfreie Prüfung - Standardprüfverfahren zur Bestimmung von Eigenspannungen durch Neutronenbeugung (ISO/TS 21432:2005/Cor 1:2008)Essais non destructifs - Méthode normalisée de détermination des contraintes résiduelles par diffraction de neutrons (ISO 21432:2005/Cor 1:2008)Non-destructive testing - Standards test method for determining residual stresses by neutron diffraction (ISO 21432:2005/Cor 1:2008)19.100Neporušitveno preskušanjeNon-destructive testingICS:Ta slovenski standard je istoveten z:CEN ISO/TS 21432:2005/AC:2009SIST-TS CEN ISO/TS 21432:2005/AC:2009en,fr,de01-junij-2009SIST-TS CEN ISO/TS 21432:2005/AC:2009SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMCEN ISO/TS 21432:2005/ACApril 2009Avril 2009April 2009ICS 19.100English versionVersion FrançaiseDeutsche FassungNon-destructive testing - Standards test method for determining residualstresses by neutron diffraction (ISO 21432:2005/Cor 1:2008)Essais non destructifs - Méthodenormalisée de détermination descontraintes résiduelles par diffraction deneutrons (ISO 21432:2005/Cor 1:2008)Zerstörungsfreie Prüfung -Standardprüfverfahren zur Bestimmung vonEigenspannungen durchNeutronenbeugung (ISO/TS21432:2005/Cor 1:2008)This corrigendum becomes effective on 8 April 2009 for incorporation in the three official languageversions of the EN.Ce corrigendum prendra effet le 8 avril 2009 pour incorporation dans les trois versions linguistiquesofficielles de la EN.Die Berichtigung tritt am 8.April 2009 zur Einarbeitung in die drei offiziellen Sprachfassungen der ENin Kraft.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Tous droits d'exploi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 16810:2024(Main)
Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2024)
SIST EN ISO 16810:2025

This document specifies the general principles for the ultrasonic testing of industrial products that permit the transmission of ultrasound.
The specific conditions of application and use of ultrasonic testing, which depend on the type of product to be tested, are described in documents which can include:
—     product standards;
—     specifications;
—     codes;
—     contractual documents;
—     written procedures.
This document specifies the minimum applicable requirements, unless otherwise specified in the referencing documents.
This document does not specify:
—     extent of testing and scan plans;
—     acceptance criteria.
This document describes only conventional probes, however, the general principles for ultrasonic testing also apply to ultrasonic testing using array techniques. If array techniques are used, then additional steps or verifications can be needed.

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15708-1:2024(Main)
Non-destructive testing - Radiation methods for computed tomography - Part 1: Vocabulary (ISO 15708-1:2024)
SIST EN ISO 15708-1:2025

This document defines terms used in the field of computed tomography (CT). It presents vocabulary that is not only CT-specific but which also includes other more generic terms and definitions spanning imaging and radiography. Some of the definitions represent discussion points aimed at refocusing their terms in the specific context of computed tomography.

  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18563-2:2024(Main)
Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2: Array probes (ISO 18563-2:2024)
SIST EN ISO 18563-2:2024

This document specifies characterization tests to be performed at the end of the fabrication of an array probe. It defines both methodology and acceptance criteria.
This document is applicable to the following array probes used for ultrasonic non-destructive testing [phased array technique or signal processing technique, e.g. full-matrix capture (FMC) and total-focusing technique (TFM)] in contact technique (with or without a wedge or delay line) or in immersion technique, with centre frequencies in the range 0,5 MHz to 10 MHz:
a)       array probes with elements in one direction:
—    1-D-linear array (linear array);
—    1-D-curved array;
—    annular array;
b)       array probes with elements in two directions:
—    2-D-array (matrix array);
—    sectorial annular array;
—    partial sectorial annular array.
This document does not give methods and acceptance criteria to characterize the performance of an ultrasonic phased array instrument or the performance of a complete system, which are given in ISO 18563–1 and in ISO 18563–3.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19675:2024(Main)
Non-destructive testing - Ultrasonic testing - Specification for a calibration block for phased array testing (PAUT) (ISO 19675:2017)
SIST EN ISO 19675:2024

The document specifies requirements for the dimensions, material and manufacture of a steel
block for calibrating ultrasonic test equipment used in ultrasonic testing with the phased array
technique

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18081:2024(Main)
Non-destructive testing - Acoustic emission testing (AT) - Leak detection by means of acoustic emission (ISO 18081:2024)
SIST EN ISO 18081:2024

This document specifies the general principles required for leak detection by acoustic emission testing (AT). It is addressed to the application of the methodology on structures and components, where a leak flow as a result of pressure differences appears and generates acoustic emission (AE).
It describes phenomena of the AE generation and influence of the nature of fluids, shape of the gap, wave propagation and environment.
The different application techniques, instrumentation and presentation of AE results are discussed. Also included are guidelines for the preparation of application documents which describe specific requirements for the application of the acoustic emission testing.
Annex A gives procedures for some leak-testing applications.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16946:2024(Main)
Non-destructive testing - Ultrasonic testing - Specification for a step wedge standard block (ISO 16946:2024)
SIST EN ISO 16946:2024

This document specifies the requirements for the dimensions, material, and manufacture of a steel step wedge standard block for the setting of an ultrasonic instrument.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18563-3:2024(Main)
Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 3: Complete systems (ISO 18563-3:2024)
SIST EN ISO 18563-3:2024

This document addresses ultrasonic test systems implementing array probes, for contact technique (with or without wedge) or for immersion technique, with centre frequencies in the range of 0,5 MHz to 10 MHz.
This document provides methods and acceptance criteria for determining the compliance of the complete system (see 3.2). Its purpose is for the verification of the correct operation of the system prior to testing or verification of the absence of degradation of the system.
The methods are not intended to prove the suitability of the system for particular applications but are intended to prove the capability of the complete system (used for an application) to operate correctly according to the settings used. Tests can be performed on individual ultrasonic beams (for phased array technique, see 9.4.4) or on resulting images (for phased array technique and total focusing technique, see 9.4.3).
The tests can be limited to the functions that are intended to be used for a certain application.
This document does not cover the sensitivity setting of the system for a specific application. Nor does it apply to the characterization or verification of the mechanical scanning equipment. It is intended that these items will be covered by the test procedure.
This document does not address the phased array technique using tandem technique.
The characterization of beams, as recommended in case of dead elements or for more in-depth knowledge of the beams, is presented in Annex A. It is not applicable for signal processing technology using arrays.
NOTE            Unless stated otherwise, in this document ‘TFM’ and ‘TFM technique’ refer to the total focusing technique as defined in ISO 23243, and to related techniques, see for example ISO 23865 and ISO 23234.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5580:2023(Main)
Non-destructive testing - Industrial radiographic illuminators - Minimum requirements (ISO 5580:2023)
SIST EN ISO 5580:2024

The function of an industrial radiographic illuminator is to provide sufficient diffuse light for viewing of developed radiographic films (radiographs).
This document specifies the minimum requirements for industrial radiographic illuminators used for viewing radiographs.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 7963:2022(Main)
Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 2 (ISO 7963:2022)
SIST EN ISO 7963:2023

This document specifies the requirements for the dimensions, material, manufacture and methods of use for calibration block No. 2 for setting and checking ultrasonic test equipment.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18563-1:2022(Main)
Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 1: Instruments (ISO 18563-1:2022)
SIST EN ISO 18563-1:2022

This document specifies the functional characteristics of multi-channel ultrasonic phased array instruments used for array probes and provides methods for their measurement and verification.
This document is also applicable to ultrasonic phased array instruments in automated systems; but other tests can be needed to ensure satisfactory performance. When the phased array instrument is a part of an automated system, the acceptance criteria can be modified by agreement between the parties involved.
This document also can partly be applicable to FMC instruments and TFM instruments.
This document gives the extent of the verification and defines acceptance criteria within a frequency range of 0,5 MHz to 10 MHz.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day