EN 13285:2010
(Main)Unbound mixtures - Specifications
Unbound mixtures - Specifications
This European Standard specifies requirements for unbound mixtures used for construction and maintenance of roads, airfields and other trafficked areas. The requirements are defined with appropriate cross-reference to EN 13242.
This European Standard applies to unbound mixtures of natural, artificial and recycled aggregates with a upper sieve size (D) from 8 mm to 90 mm and lower sieve size (d) = 0 at the point of delivery.
NOTE 1 Mixtures with an upper sieve size (D) greater than 90 mm are not covered by this European Standard but may be specified in the place of use.
NOTE 2 Water content of the mixture and the density of the installed layer are not specified mixture requirements. Both parameters are related to the control of the construction of the layer and are outside the scope of this European Standard.
Ungebundene Gemische - Anforderungen
Diese Europäische Norm legt Anforderungen an ungebundene Gemische fest, die beim Bau und bei der Instandhaltung von Straßen, Flugplätzen und anderen Verkehrsflächen angewendet werden. Die Anforde-rungen werden unter entsprechenden Querverweisen auf EN 13242 festgelegt. Diese Europäische Norm gilt für ungebundene Gemische aus natürlichen, künstlichen und rezyklierten Gesteinskörnungen mit einer oberen Siebgröße (D) von 8 mm bis 90 mm und einer unteren Siebgröße (d) = 0 bei der Auslieferung. ANMERKUNG 1 Gemische mit einer oberen Siebgröße (D) größer als 90 mm werden in dieser Europäischen Norm nicht erfasst, dürfen jedoch unter den am Verwendungsort geltenden Bedingungen eingesetzt werden. ANMERKUNG 2 Der Wassergehalt des Gemisches und die Dichte der eingebauten Schicht sind keine für die Gemische vorgeschriebenen Anforderungen. Beide Eigenschaften hängen von der Überwachung der eingebauten Schicht ab und liegen außerhalb des Anwendungsbereiches dieser Europäischen Norm.
Graves non traitées - Spécifications
Cette Norme européenne spécifie les exigences relatives aux mélanges non traités utilisés pour la
construction et l'entretien des routes, des aérodromes et d'autres aires de trafic. Ces exigences sont définies
en accord avec l'EN 13242.
Cette Norme européenne s'applique aux mélanges non traités de granulats naturels, artificiels et recyclés
ayant une dimension maximale des grains (D) comprise entre 8 mm et 90 mm et une dimension minimale des
grains (d) = 0 à la livraison.
NOTE 1 Les mélanges dont la dimension maximale des grains (D) dépasse 90 mm ne sont pas couverts par cette
Norme européenne, mais peuvent être spécifiés sur les lieux d'utilisation.
NOTE 2 La teneur en eau du mélange et la masse volumique de la couche mise en place ne sont pas des exigences
spécifiées. Ces deux paramètres concernent le contrôle de la construction de la couche et sortent du cadre de cette
Norme européenne.
Nevezane zmesi - Zahteve
Ta evropski standard določa zahteve za nevezane zmesi, ki se uporabljajo za gradnjo in vzdrževanje cest, letaliških stez in drugih povoznih območij. Zahteve so opredeljene z ustreznim navzkrižnim sklicevanjem na EN 13242. Ta evropski standard velja za nevezane zmesi naravnih, umetnih in recikliranih agregatov z zgornjo velikostjo zrn (D) med 8 mm in 90 mm ter spodnjo velikostjo zrn (d) = 0 na točki dostave. OPOMBA 1: Ta evropski standard ne zajema zmesi z zgornjo velikostjo zrn (D), ki presega 90 mm, vendar se lahko določijo na mestu uporabe. OPOMBA 2: Delež vode v zmesi in gostota nameščene plasti nista opredeljeni zahtevi za zmesi. Oba parametra sta povezana z nadzorom gradnje plasti in nista predmet tega evropskega standarda.
General Information
- Status
- Withdrawn
- Publication Date
- 14-Sep-2010
- Withdrawal Date
- 20-Jan-2026
- Technical Committee
- CEN/TC 227 - Road materials
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 27-Jun-2018
- Completion Date
- 28-Jan-2026
Relations
- Effective Date
- 18-Sep-2010
- Effective Date
- 15-Jul-2018
- Refers
EN 1744-1:2009+A1:2012 - Tests for chemical properties of aggregates - Part 1: Chemical analysis - Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
Frequently Asked Questions
EN 13285:2010 is a standard published by the European Committee for Standardization (CEN). Its full title is "Unbound mixtures - Specifications". This standard covers: This European Standard specifies requirements for unbound mixtures used for construction and maintenance of roads, airfields and other trafficked areas. The requirements are defined with appropriate cross-reference to EN 13242. This European Standard applies to unbound mixtures of natural, artificial and recycled aggregates with a upper sieve size (D) from 8 mm to 90 mm and lower sieve size (d) = 0 at the point of delivery. NOTE 1 Mixtures with an upper sieve size (D) greater than 90 mm are not covered by this European Standard but may be specified in the place of use. NOTE 2 Water content of the mixture and the density of the installed layer are not specified mixture requirements. Both parameters are related to the control of the construction of the layer and are outside the scope of this European Standard.
This European Standard specifies requirements for unbound mixtures used for construction and maintenance of roads, airfields and other trafficked areas. The requirements are defined with appropriate cross-reference to EN 13242. This European Standard applies to unbound mixtures of natural, artificial and recycled aggregates with a upper sieve size (D) from 8 mm to 90 mm and lower sieve size (d) = 0 at the point of delivery. NOTE 1 Mixtures with an upper sieve size (D) greater than 90 mm are not covered by this European Standard but may be specified in the place of use. NOTE 2 Water content of the mixture and the density of the installed layer are not specified mixture requirements. Both parameters are related to the control of the construction of the layer and are outside the scope of this European Standard.
EN 13285:2010 is classified under the following ICS (International Classification for Standards) categories: 93.080.20 - Road construction materials. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 13285:2010 has the following relationships with other standards: It is inter standard links to EN 13285:2003, EN 13285:2018, EN 1744-1:2009+A1:2012, EN 13286-5:2003, EN 13286-4:2021, EN 13242:2002+A1:2007, EN 933-1:2012, EN 13286-1:2021, EN 13286-2:2010, EN 13286-3:2003. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 13285:2010 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Nevezane zmesi - ZahteveUngebundene Gemische - AnforderungenGraves non traitées - SpécificationsUnbound mixtures - Specifications93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 13285:2010SIST EN 13285:2010en,fr,de01-december-2010SIST EN 13285:2010SLOVENSKI
STANDARDSIST EN 13285:20041DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13285
September 2010 ICS 93.080.20 Supersedes EN 13285:2003English Version
Unbound mixtures - Specifications
Graves non traitées - Spécifications
Ungebundene Gemische - Anforderungen This European Standard was approved by CEN on 29 July 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13285:2010: ESIST EN 13285:2010
Use of the supplier declared value. 14A.1 Terminology . 14A.2 Overall grading range . 14A.3 Supplier declared value grading range . 15A.4 Supplier declared value . 15A.5 Tolerances for comparison with the supplier declared value . 15Annex B (informative)
Guidance on the assessment of the mechanical behaviour of unbound mixtures . 16Annex C (normative)
Factory production control . 17C.1 Introduction . 17C.2 Organization . 17C.2.1 Responsibility and authority . 17C.2.2 Management representative for factory production control . 17C.2.3 Management review . 17C.3 Control procedures. 17C.3.1 Document and data control . 17C.3.2 Sub-contract services . 18C.3.3 Knowledge of mixture components . 18C.4 Management of the production . 18C.5 Inspection and test . 18C.5.1 General . 18C.5.2 Equipment . 18C.5.3 Frequency and location of inspections, sampling and tests . 19C.6 Records . 20C.7 Control of non-conforming product . 20SIST EN 13285:2010
When required, the percentage of particles passing the 0,063 mm sieve shall also be greater than the values given in Table 3, according to the category chosen. Table 3 — Minimum fines content Percentage passing 0,063 mm sieve by mass Category ≥ 2 LF2 ≥ 4 LF4 ≥ 8 LF8 No requirement LFN
The categories in Table 2 and Table 3 shall be chosen so that the difference between the maximum fines content and the minimum fines content is not less than 3 %. SIST EN 13285:2010
4.4 Grading requirements 4.4.1 General grading curve When required, the percentage by mass passing sieve A, sieve B, sieve C, sieve E and where specified in Table 6 sieve F and sieve G determined in accordance with EN 933-1 using the sieves defined in Table 5 shall be within the overall grading range appropriate to the category selected from Table 6. SIST EN 13285:2010
In addition, for categories GA, GB, GC, GO and GP the mean value calculated from all gradings shall be within the supplier declared value grading range appropriate to the category selected from Table 6. SIST EN 13285:2010
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...