prEN 9300-007

SLOVENSKI STANDARD
01-julij-2023
Nadomešča:
SIST EN 9300-007:2017
Aeronavtika - LOTAR - Dolgoročno arhiviranje in pridobivanje digitalne tehnične
dokumentacije o izdelkih, kot so podatki o 3D, CAD in PDM - 007. del: Izrazi in
reference
Aerospace series - LOTAR -LOng Term Archiving and Retrieval of digital technical
product documentation such as 3D, CAD and PDM data - Part 007: Terms and
references
Luft- und Raumfahrt - LOTAR - Langzeit-Archivierung und -Bereitstellung digitaler
technischer Produktdokumentationen, wie zum Beispiel von 3D-, CAD- und PDM-Daten -
Teil 007: Begriffe und Verweisungen
Série aérospatiale - LOTAR - Archivage long terme et récupération des données
techniques produits numériques telles que CAD 3D et PDM - Partie 007 : Termes and
réferences
Ta slovenski standard je istoveten z: prEN 9300-007
ICS:
01.110 Tehnična dokumentacija za Technical product
izdelke documentation
35.240.30 Uporabniške rešitve IT v IT applications in information,
informatiki, dokumentiranju in documentation and
založništvu publishing
49.020 Letala in vesoljska vozila na Aircraft and space vehicles in
splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2023
ICS 35.240.30; 01.110; 35.240.60; 49.020 Will supersede EN 9300-007:2017
English Version
Aerospace series - LOTAR -LOng Term Archiving and
Retrieval of digital technical product documentation such
as 3D, CAD and PDM data - Part 007: Terms and references
Série aérospatiale - LOTAR - Archivage long terme et Luft- und Raumfahrt - LOTAR - Langzeit-Archivierung
récupération des données techniques produits und -Bereitstellung digitaler technischer
numériques telles que CAD 3D et PDM - Partie 007 : Produktdokumentationen, wie zum Beispiel von 3D-,
Termes and réferences CAD- und PDM-Daten - Teil 007: Begriffe und
Verweisungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 9300-007:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 General terms, definitions and abbreviations. 5
3.1 Terms and references . 5
3.2 Abbreviations . 34
4 Applicability . 38
Bibliography . 39

European foreword
This document (prEN 9300-007:2022) has been prepared by the Aerospace and Defence Industries
Association of Europe — Standardization (ASD-STAN).
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 9300-007:2017.
Introduction
This document was prepared jointly by AIA, ASD-STAN, PDES, Inc., AFNet and the prostep ivip
Association.
The AFNeT non-profit association has operated for more than 30 years a multi-sectoral “Think Tank”
articulated with a “Do Tank”, with digital transformation projects or standardization projects in many
industries. These activities have led to the emergence of a network of recognized and highly skilled
actors from the manufacturing industry, IT businesses, and research companies. Its members represent
leading industrial companies, SMEs, French governmental agencies, software vendors, universities, and
research organisations. AFNeT has conducted voluntary and innovative actions in order to develop
competitiveness and innovation in industry by setting up collaboration projects or programs in the
industrial sectors (Aerospace & Defence, Automotive, Rail, Shipbuilding, Nuclear, Energy, etc.) to enable
the digital thread for the extended enterprise processes such as Product Lifecycle Management, Supply-
Chain Management, Manufacturing, Maintenance & Operations, Integrated Logistics Support, and
Identification. AFNet promotes the development, testing and usage of a set of coherent international
standards for supporting these activities, especially in the PLM and the SCM domains.
The prostep ivip Association is an international non-profit association in Europe. For establishing
leadership in IT-based engineering it offers a moderated platform to its nearly 200 members from
leading industries, system vendors and research institutions. Its product and process data
standardization activities at European and worldwide levels are well known and accepted. The prostep
ivip Association sees this standard and the related parts as a milestone of product data technology.
PDES, Inc. is an international non-profit association in USA. The mission of PDES, Inc. is to accelerate the
development and implementation of ISO 10303, enabling enterprise integration and PLM
interoperability for member companies. PDES, Inc. gathers members from leading manufacturers,
national government agencies, PLM vendors and research organisations. PDES, Inc. supports this
standard as an industry resource to sustain the interoperability of digital product information, ensuring
and maintaining authentic longevity throughout their product lifecycle.
Readers of this document should note that all standards undergo periodic revisions and that any
reference made herein to any other standard implies its latest edition, unless otherwise stated
The standards will be published under two different standards organisations using different prefixes.
ASD-STAN will publish the standard under the number EN 9300–xxx. AIA will publish the standard
under the number NAS 9300–xxx. The content in the EN 9300 and NAS 9300 documents will be the
same. The differences will be noted in the reference documentation (i.e. for EN 9300 Geometric
Dimensioning & Tolerancing will be referenced in ISO 1101 and ISO 16792, and for NAS 9300 the same
information will be referenced in ASME Y14.5M and Y 14.41). The document formatting etc., will follow
that of the respective editorial rules of ASD-STAN and AIA.
1 Scope
This document defines the common terms, abbreviations and references used through the EN 9300
series of standard parts.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 14721, Space data and information transfer systems — Open archival information system (OAIS) —
Reference model
NAS 9300 (all parts), Aerospace series — LOTAR — LOng Term Archiving and Retrieval of digital
technical and product documentation such as 3D, CAD and PDM data
3 General terms, definitions and abbreviations
3.1 Terms and references
For the purposes of this document, the terms and definitions given in NAS 9300 (all parts) and the
following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
The following section provides a list of general terms that occur in the NAS 9300 set of documentation,
together with a description of what the terms mean. As the meaning of a term may change with context,
this section records the usage of those terms in the context of NAS 9300 and is provided to enable the
correct interpretation of the NAS 9300 standard. These descriptions are not otherwise normative.
3.1.1
3D annotation
text, notes, flag notes, dimensions, tolerances, or GD&T that is modelled in 3D space with leaders
pointing to the solid model features
3.1.2
3D model-based definition/model-based definition
MBD
set of concepts, processes, and tools that allow the creation of an annotated 3D product definition based
on a 3D solid model
Note 1 to entry: The MBD dataset includes all Engineering Intent requirements (including process
specifications, geometric dimensioning and tolerancing (GD&T), product and manufacturing information (PMI),
and other required information). Combined with product lifecycle management (PLM) attributes, a parts list, and
general notes, this constitutes an authoritative, single source of master product definition data that does not
include or depend upon traditional 2D drawings; the MBD dataset defines complete requirements for a product in
its nominal condition as well as permissible limits of variation and other acceptance criteria, providing all the data
needed to plan, fabricate, and validate an article of product hardware.
3.1.3
access
from the OAIS model, the process of recovering data from the archive
3.1.4
adhesive
substance used to bind two or more other components together via surface contact
Note 1 to entry: The adhesive can be a film, paste or liquid.
3.1.5
administration
management of the archive and its daily operation according to OAIS
3.1.6
administrator
organisation or person responsible for management of the archive and its daily operation
3.1.7
advanced composite structure
hybrid structure in which composite laminates of materials with high strength and stiffness with a resin
matrix (thermoset or thermoplastic) are used in combination with other components (like core, fibre
optics, active electronics, passive electronics, metal, .) in order to create a multi-functional design
3.1.8
allowable
material strength, strain or load which can be used as a basis for generating a margin of safety from
3.1.9
analysis and simulation models
single domain, multi-domain, or domain unspecific models which can be used to describe and validate
the functional architecture, or estimate the operational performance, control or behaviour of a
component, system or product
Note 1 to entry: The models are an assessment of temporal, physics-based, or mathematical properties. The
models may support the development or prototyping of production software, code generation and network
integration. These specialized models support design optimization, validation and reduce risk. Simulation models
use the basis of the analysis to represent the interactions between topologies, systems, subsystems or component
designs based on time or other event sequences.
3.1.10
anisotropic
exhibiting different properties along axes in different directions
3.1.11
application activity model
AAM
model of activities that defines the context for a particular application protocol
[SOURCE: STEP]
3.1.12
application interpreted model
AIM
one of the STEP information models, historically used as the basis for implementation
3.1.13
application protocol
AP
one of the major parts of the standard that provides an implementable data exchange in a particular
context
[SOURCE: STEP]
3.1.14
application reference model
ARM
information model that describes the information requirements and constraints of a specific application
context
[SOURCE: STEP]
3.1.15
archival information package
AIP
information package consisting of the content information and the associated preservation description
information (PDI), which is preserved within an OAIS
Note 1 to entry: This is the package actually retained by the archive, containi
...