Adhesives for load-bearing timber structures - Test methods - Part 5: Determination of maximum assembly time under referenced conditions

This European Standard specifies a laboratory method of determining the maximum assembly time at two spread rate levels in standard atmosphere [20/65].
This European Standard is intended for obtaining a reliable base of comparison of the maximum assembly time between adhesives at referenced conditions.

Klebstoffe für tragende Holzbauteile - Prüfverfahren - Teil 5: Bestimmung der maximalen Wartezeit bei Referenzbedingungen

Diese Europäische Norm legt ein Labor-Verfahren zur Bestimmung der maximalen Wartezeit von Klebstoffen bei zwei unterschiedlichen aufgetragenen Klebstoffmengen im Normalklima 20/65 fest.
Diese Europäische Norm dient dazu, eine zuverlässige Grundlage zum Vergleich der maximalen Wartezeit von Klebstoffen unter Referenzbedingungen zu erhalten.

Adhésifs pour structures portantes en bois - Méthodes d'essai - Partie 5: Détermination du temps d'assemblage maximal dans des conditions de référence

La présente Norme européenne spécifie une méthode de laboratoire permettant de déterminer le temps d'assemblage maximal pour deux niveaux de grammage en atmosphère normale [20/65].
La présente Norme européenne vise à fournir une base fiable de comparaison de la durée conventionnelle maximale d'assemblage entre les adhésifs dans des conditions de référence.

Lepila za nosilne lesene konstrukcije - Preskusne metode - 5. del: Določanje najdaljšega časa za montažo (sestavo) pri referenčnih pogojih

Ta evropski standard določa laboratorijsko metodo za določanje najdaljšega časa za montažo (sestavo) pri dveh hitrostih nanašanja v standardni atmosferi [20/65]. Ta evropski standard je namenjen za pridobivanje zanesljive podlage za primerjavo najdaljšega časa za montažo med lepili pri referenčnih pogojih.

General Information

Status
Withdrawn
Publication Date
26-Mar-2013
Withdrawal Date
13-Apr-2025
ICS
83.180 - Adhesives
Technical Committee
CEN/TC 193 - Adhesives
Drafting Committee
CEN/TC 193/SC 1/WG 8 - Revision of EN 301 and EN 302
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
15-Feb-2023
Completion Date
14-Apr-2025
Ref Project
SIST EN 302-5:2013 - Adhesives for load-bearing structures - Test methods - Part 5: Determination of maximum assembly time under referenced conditions

Relations

Replaces
ENV 302-5:2001 - Adhesives for load-bearing timber structures - Test methods - Part 5: Determination of the conventional assembly time
Effective Date
28-Aug-2010
Replaced By
EN 302-5:2023 - Adhesives for load-bearing timber structures - Test methods - Part 5: Determination of maximum assembly time under referenced conditions
Effective Date
18-Sep-2019

Frequently Asked Questions

EN 302-5:2013 is a standard published by the European Committee for Standardization (CEN). Its full title is "Adhesives for load-bearing timber structures - Test methods - Part 5: Determination of maximum assembly time under referenced conditions". This standard covers: This European Standard specifies a laboratory method of determining the maximum assembly time at two spread rate levels in standard atmosphere [20/65]. This European Standard is intended for obtaining a reliable base of comparison of the maximum assembly time between adhesives at referenced conditions.

This European Standard specifies a laboratory method of determining the maximum assembly time at two spread rate levels in standard atmosphere [20/65]. This European Standard is intended for obtaining a reliable base of comparison of the maximum assembly time between adhesives at referenced conditions.

EN 302-5:2013 is classified under the following ICS (International Classification for Standards) categories: 83.180 - Adhesives. The ICS classification helps identify the subject area and facilitates finding related standards.

EN 302-5:2013 has the following relationships with other standards: It is inter standard links to ENV 302-5:2001, EN 302-5:2023. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

You can purchase EN 302-5:2013 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Klebstoffe für tragende Holzbauteile - Prüfverfahren - Teil 5: Bestimmung der maximalen Antrockenzeit bei ReferenzbedingungenAdhésifs pour structures portantes en bois - Méthodes d'essai - Partie 5: Détermination du temps d’assemblage maximal dans des conditions de référenceAdhesives for load-bearing structures - Test methods - Part 5: Determination of maximum assembly time under referenced conditions91.080.20Lesene konstrukcijeTimber structures83.180LepilaAdhesivesICS:Ta slovenski standard je istoveten z:EN 302-5:2013SIST EN 302-5:2013en,de01-maj-2013SIST EN 302-5:2013SLOVENSKI
STANDARDSIST ENV 302-5:20021DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 302-5
March 2013 ICS 83.180 Supersedes ENV 302-5:2001English Version
Adhesives for load-bearing structures - Test methods - Part 5: Determination of maximum assembly time under referenced conditions
Adhésifs pour structures portantes en bois - Méthodes d'essai - Partie 5: Détermination du temps d'assemblage maximal dans des conditions de référence
Klebstoffe für tragende Holzbauteile - Prüfverfahren - Teil 5: Bestimmung der maximalen Wartezeit bei Referenzbedingungen This European Standard was approved by CEN on 5 February 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 302-5:2013: ESIST EN 302-5:2013

These European Standards have the following titles: EN 301, Adhesives, phenolic and aminoplastic, for load-bearing timber structures — Classification and performance requirements EN 15425, Adhesives — One component polyurethane for load performance requirements prEN 16254, Adhesives — Emulsion polymerized isocyanate (EPI) for load-Classification and performance requirements EN 302, Adhesives for load-bearing timber structures — Test methods
 Part 1: Determination of longitudinal tensile shear strength  Part 2: Determination of resistance to delamination  Part 3: Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength  Part 4: Determination of the effects of wood shrinkage on the shear strength  Part 5: Determination of maximum assembly time under referenced conditions  Part 6: Determination of the minimum pressing time under referenced conditions  Part 7: Determination of the working life under referenced conditions EN 15416, Adhesives for load bearing timber structures other than phenolic and aminoplastic — Test methods  Part 2: Static load test of multiple bondline specimens in compression shear  Part 3: Creep deformation test at cyclic climate conditions with specimens loaded in bending shear  Part 4: Determination of open assembly time for one component polyurethane adhesives  Part 5: Determination of conventional pressing time
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...

The article discusses a European standard, EN 302-5:2013, which outlines a laboratory method for determining the maximum assembly time for adhesives used in load-bearing timber structures. The standard aims to provide a reliable basis for comparing maximum assembly times between different adhesives under specified conditions.

기사 제목 : EN 302-5:2013 - 하중지지목구조용 접착제 - 시험 방법 - 제 5부: 기준 조건에서 최대 조립 시간 결정 기사 내용: 이 유럽 표준은 표준 대기 조건 [20/65]에서 두 가지 분포율 수준에서 최대 조립 시간을 결정하는 실험실 방법을 명시합니다. 이 유럽 표준은 기준 조건에서 다양한 접착제 사이의 최대 조립 시간을 비교하기 위한 신뢰할 수 있는 기준을 제공하는 것을 목표로 합니다.

記事のタイトル：EN 302-5：2013 - 負荷を支える木造構造物のための接着剤 - 試験方法 - 第5部：参照条件下での最大組み立て時間の決定 記事の内容：この欧州標準は、標準大気（20/65）における2つの広げ率レベルで最大組み立て時間を決定するための実験室の方法を指定しています。 この欧州標準は、参照条件下での異なる接着剤の最大組み立て時間を比較するための信頼性のある基準を提供することを目的としています。