EN ISO 10545-6:1997

SLOVENSKI STANDARD
01-april-1998
.HUDPLþQHSORãþLFHGHO8JRWDYOMDQMHRGSRUQRVWLQHORãþHQLKSORãþLFSURWL
JORELQVNLREUDEL
Ceramic tiles - Part 6: Determination of resistance to deep abrasion for unglazed tiles
(ISO 10545-6:1995)
Keramischen Fliesen und Platten - Teil 6: Bestimmung des Widerstandes gegen
Teifenverschließ-Unglasierte Fliesen und Platten (ISO 10545-6:1995)
Carreaux et dalles céramiques - Partie 6: Détermination de la résistance a l'abrasion
profonde pour les carreaux non emaillés (ISO 10545-6:1995)
Ta slovenski standard je istoveten z: EN ISO 10545-6:1997
ICS:
91.100.23 .HUDPLþQHSORãþLFH Ceramic tiles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

ISO
INTERNATIONAL
STANDARD 1054545
First edition
1995-11-01
Ceramic tiles -
Part 6:
Determination of resistance to deep abrasion for
unglazed tiles
Carreaux et dalles ckramiques -
Partie 6: Determination de Ia rhistance A I’abrasion profonde pour les
carreaux non 6mailk
Reference number
ISO 10545-6:1995(E)
ISO 10545=6:1995(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide fed-
eration of national Standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO tech-
nical committees. Esch member body interested in a subject for which a
technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO collab-
orates closely with the International Electrotechnical Commission (IEC) on
all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are cir-
culated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 10545-6 was prepared by Technical Committee
lSO/TC 189, Ceramic tile.
ISO 10545 consists of the following Parts, under the general title Ceramic
tiles:
- Part 7: Sampling and basis for acceptance
- Part 2: Determination of dimensions and surface quality
- Part 3: Determination of wa ter absorption, apparen t porosity, apparen t
relative density and bulk density
- Part 4: Determination of modulus of rupture and breaking strength
coef-
- Part 5: Determination of impac t resistance by measurement of
ficien t of restitution
- Part 6: Determination of resis tance to deep abrasion for unglazed tiles
0 ISO 1995
All rights reserved. Unless otherwise specified, no patt of this publication may be reproduced
or utilized in any form or by any means, electronie or mechanical, including photocopying and
microfilm, without Permission in writing from the publisher.
zation for Standardization
International Organi
CH-l 2 11 Geneve 20 l Swi tzerland
Case postale 56 l
Printed in Switzerland
ISO 105456:1995(E)
0 ISO
- Part 7: Determination of resistance to surface abrasion for glazed tiles
- Part 8: Determination of linear thermal expansion
- Part 9: Determination of resistance to thermal shock
- Part IO: Determination o f mois ture expansion
- Part I 7: De fermination of crazing resistance for glazed tiles
- Part 12: Determination of fros t resistance
- Part 73: Determination of Chemical resistance
- Part 14: Determination of resistance to stains
- Part 15: Determination of lead and Cadmium given off by glazed tiles
- Part 16: Determination of small colour differentes
- Part 77: Determination of coefficient of friction

This page intentionally left blank

INTERNATIONAL STANDARD 0 ISO ISO 1054506:1995(E)
Ceramic tiles -
Part 6:
Determination of resistance to deep abrasion for unglazed tiles
1 Scope 4 Apparatus
4.1 Abrasion apparatus, (see figure l), consisting
This part of ISO 10545 specifies a test method for
essentially of a rotating disc, a storage hopper with a
determining the resistance to deep abrasion of all
dispensing device for the abrasive material, a test
unglazed ceramic tiles used for floor coverings.
specimen support and a counterweight.
The disc is made of E 235 A (Fe 360 A) (ISO 630-1)
with a diameter of (200 + 0,2) mm and thickness at
2 Normative refer
...