EN ISO 10545-1:2014

SLOVENSKI STANDARD
01-januar-2015
1DGRPHãþD
SIST EN ISO 10545-1:1998
.HUDPLþQHSORãþLFHGHO9]RUþHQMHLQRVQRYH]DVSUHMHP,62
Ceramic tiles - Part 1: Sampling and basis for acceptance (ISO 10545-1:2014)
Keramische Fliesen und Platten - Teil 1: Probename und Grundlagen für die Annahme
(ISO 10545-1:2014)
Carreaux et dalles céramiques - Partie 1: Échantillonnage et conditions de réception
(ISO 10545-1:2014)
Ta slovenski standard je istoveten z: EN ISO 10545-1:2014
ICS:
91.100.23 .HUDPLþQHSORãþLFH Ceramic tiles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 10545-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2014
ICS 91.100.23 Supersedes EN ISO 10545-1:1997
English Version
Ceramic tiles - Part 1: Sampling and basis for acceptance (ISO
10545-1:2014)
Carreaux et dalles céramiques - Partie 1: Échantillonnage Keramische Fliesen und Platten - Teil 1: Probename und
et conditions de réception (ISO 10545-1:2014) Grundlagen für die Annahme (ISO 10545-1:2014)
This European Standard was approved by CEN on 6 September 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10545-1:2014 E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 10545-1:2014) has been prepared by Technical Committee ISO/TC 189 “Ceramic
tile” in collaboration with Technical Committee CEN/TC 67 “Ceramic tiles” the secretariat of which is held by
UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2015, and conflicting national standards shall be withdrawn at the
latest by April 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10545-1:1997.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10545-1:2014 has been approved by CEN as EN ISO 10545-1:2014 without any modification.

INTERNATIONAL ISO
STANDARD 10545-1
Second edition
2014-10-01
Ceramic tiles —
Part 1:
Sampling and basis for acceptance
Carreaux et dalles céramiques —
Partie 1: Échantillonnage et conditions de réception
Reference number
ISO 10545-1:2014(E)
©
ISO 2014
ISO 10545-1:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

ISO 10545-1:2014(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Terms and definitions . 1
3 Principle . 2
4 Constitution of inspection lots . 2
5 Extent of the inspection . 2
6 Sampling . 2
7 Inspection . 2
8 Determination of acceptability of inspection lots . 3
8.1 Inspection by attributes . 3
8.2 Inspection by the average value . 3
9 Acceptance Report . 3
Bibliography . 8
ISO 10545-1:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 189, Ceramic Tiles.
This second edition cancels and replaces the first edition (ISO 10545-1:1995), which has been technically
revised.
ISO 10545 consists of the following parts, under the general title Ceramic Tiles:
— Part 1: Sampling and basis for acceptance
— Part 2: Determination of dimensions and surface quality
— Part 3: Determination of water absorption, apparent porosity, apparent relative density and bulk
density
— Part 4: Determination of modulus of rupture and breaking strength
— Part 5: Determination of impact resistance by measurement of coefficient of restitution
— Part 6: Determination of resistance to deep abrasion for unglazed tiles
— Part 7: Determination of resistance to surface abrasion for glazed tiles
— Part 8: Determination of linear thermal expansion
— Part 9: Determination of resistance to thermal shock
— Part 10: Determination of moisture expansion
— Part 11: Determination of crazing resistance for glazed tiles
— Part 12: Determination of frost resistance
— Part 13: Determination of chemical resistance
— Part 14: Determination of resistance to stains
iv © ISO 2014 – All rights reserved

ISO 10545-1:2014(E)
— Part 15: Determination of lead and cadmium given off by glazed tiles
— Part 16: Determination of small colour differences
INTERNATIONAL STANDARD ISO 10545-1:2014(E)
Ceramic tiles —
Part 1:
Sampling and basis for acceptance
1 Scope
This part of ISO 10545 specifies rules for batching, sampling, inspection, and acceptance/rejection of
ceramic tiles.
2 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
2.1
order
quantity of tiles ordered at one time
Note 1 to entry: An order may consist of one or more consignments.
2.2
consignment
quantity of tiles delivered during a period of 2 d
2.3
homogeneous consignment/subconsignment
consignment or subconsignment that consists of tiles from one manufacturer, produced under conditions
and with properties that are presumed uniform
2.4
inspection lot
quantity of tiles submitted for inspection manufactured by one manufacturer under conditions and
with properties that are presumed uniform
2.5
sample
specified number of tiles taken from an inspection lot
2.6
sample size
number of tiles to be tested for each property
2.7
requirement
required characteristic as specified for the property in the relevant product standard
2.8
non-conforming unit
tile that does not meet the requirement for the property concerned
ISO 10545-1:2014(E)
3 Principle
This part of ISO 10545 provides for a sampling inspection system with a double sampling plan, partly
for the method of inspection by attributes (individual values) and partly for a method of inspection by
average values (variables).
The number of tiles to be tested varies for each property (see Table 1).
4 Constitution of inspection lots
An inspection lot can consist of one or more homogeneous consignments or subconsignments.
Any consignment which is not homogeneous shall be divided into subconsignments which are assumed
to be homogeneous and which might then constitute inspection lots.
If non-homogeneity is not relevant to the properties to be tested, by agreement between the supplier
and consumer, the consignment can be treated as homogeneous.
NOTE For example, a consignment of tiles, of the same type with different glazes, can be homogeneous with
regard to dimensions and water absorption and non-homogeneous with regard to surface quality. In the same
way, accessories which differ only in shape from the remaining tiles in the sample can be considered homogeneous
with respect to the other properties.
5 Extent of the inspection
The choice of properties to be considered for inspection shall be subject to agreement between the
supplier and consumer and might depend on the size of the inspection lot.
NOTE In principle, a complete range of tests has to only be executed f
...