EN ISO 10545-2:2018
(Main)Ceramic tiles - Part 2: Determination of dimensions and surface quality (ISO 10545-2:2018)
Ceramic tiles - Part 2: Determination of dimensions and surface quality (ISO 10545-2:2018)
This document specifies methods for determining the dimensional characteristics (length, width, thickness, straightness of sides, rectangularity, surface flatness) and the surface quality of ceramic tiles.
Tiles with areas less than 4 cm2 are excluded from measurements of length, width, straightness of sides, rectangularity and surface flatness.
NOTE Spacer lugs and glaze blobs and other irregularities of the sides are intended to be ignored when measuring length, width, straightness of sides, rectangularity, if these are subsequently hidden in the joints after fixing (installation).
Keramische Fliesen und Platten - Teil 2: Bestimmung der Maße und der Oberflächenbeschaffenheit (ISO 10545-2:2018)
Carreaux céramiques - Partie 2: Détermination des caractéristiques dimensionnelles et de la qualité de surface (ISO 10545-2:2018)
Le présent document spécifie des méthodes pour la détermination des caractéristiques dimensionnelles (longueur, largeur, épaisseur, rectitude des arêtes, angularité, planéité) et de la qualité de surface de tous les carreaux et dalles céramiques.
Les carreaux ayant une surface inférieure à 4 cm2 ne sont pas soumis aux mesurages de longueur, de largeur, de rectitude des arêtes, d'angularité et de planéité.
NOTE Les tétons d'espacement, les bavures d´émail et autres irrégularités des côtés ne doivent pas être pris en considération pour le mesurage de la longueur, de la largeur, de la rectitude des arêtes et de l'angularité, si ceux-ci sont ultérieurement cachés dans les joints après la pose (installation).
Keramične ploščice - 2. del: Mere in kakovost površine (ISO 10545-2:2018)
Ta dokument določa metode za ugotavljanje dimenzijskih značilnosti (dolžina, širina, debelina, ravnost strani, pravokotnost, ploskost površine) in kakovosti površine keramičnih ploščic. Ploščice s površino manj kot 4 cm2 so izvzete iz meritev dolžine, širine, ravnosti strani, pravokotnosti in ploskosti površine.
OPOMBA: Distančniki, ostanki glazure in druge nepravilnosti so med merjenjem dolžine, širine, ravnosti strani in pravokotnosti prezrti, vendar morajo biti po pritrjevanju (nameščanju) naknadno skriti v spojih.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN ISO 10545-2:1998
.HUDPLþQHSORãþLFHGHO 0HUHLQNDNRYRVWSRYUãLQH ,62
Ceramic tiles - Part 2: Determination of dimensions and surface quality (ISO 10545-
2:2018)
Keramische Fliesen und Platten - Teil 2: Bestimmung der Maße und der
Oberflächenbeschaffenheit (ISO 10545-2:2018)
Carreaux céramiques - Partie 2: Détermination des caractéristiques dimensionnelles et
de la qualité de surface (ISO 10545-2:2018)
Ta slovenski standard je istoveten z: EN ISO 10545-2:2018
ICS:
91.100.23 .HUDPLþQHSORãþLFH Ceramic tiles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 10545-2
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 91.100.23 Supersedes EN ISO 10545-2:1997
English Version
Ceramic tiles - Part 2: Determination of dimensions and
surface quality (ISO 10545-2:2018)
Carreaux céramiques - Partie 2: Détermination des Keramische Fliesen und Platten - Teil 2: Bestimmung
caractéristiques dimensionnelles et de la qualité de der Maße und der Oberflächenbeschaffenheit (ISO
surface (ISO 10545-2:2018) 10545-2:2018)
This European Standard was approved by CEN on 16 October 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10545-2:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 10545-2:2018) has been prepared by Technical Committee ISO/TC 189
"Ceramic tile" in collaboration with Technical Committee CEN/TC 67 “Ceramic tiles” the secretariat of
which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10545-2:1997.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10545-2:2018 has been approved by CEN as EN ISO 10545-2:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 10545-2
Second edition
2018-09
Ceramic tiles —
Part 2:
Determination of dimensions and
surface quality
Carreaux et dalles céramiques —
Partie 2: Détermination des caractéristiques dimensionnelles et de la
qualité de surface
Reference number
ISO 10545-2:2018(E)
©
ISO 2018
ISO 10545-2:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
ISO 10545-2:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Measurement of length and width . 3
4.1 Apparatus . 3
4.2 Test specimens . 3
4.3 Procedure . 3
4.4 Expression of results . 3
4.5 Test report . 3
5 Measurement of thickness . 4
5.1 Apparatus . 4
5.2 Test specimens . 4
5.3 Procedure . 4
5.4 Expression of results . 4
5.5 Test report . 4
6 Measurement of straightness of sides . 5
6.1 Calculation . 5
6.2 Apparatus . 5
6.3 Test specimens . 6
6.4 Procedure . 6
6.5 Test report . 7
7 Measurement of rectangularity . 7
7.1 Calculation . 7
7.2 Apparatus . 8
7.3 Test specimens . 9
7.4 Procedure . 9
7.5 Test report . 9
8 Measurements of surface flatness (curvature and warpage) . 9
8.2 Apparatus .10
8.2.1 For tiles larger than 40 mm × 40 mm .10
8.2.2 For tiles of dimensions 40 mm × 40 mm or less .10
8.3 Test specimens .10
8.4 Procedure .10
8.4.1 For tiles larger than 40 mm × 40 mm .10
8.4.2 For tiles of dimensions 40 mm × 40 mm or less .12
8.5 Expression of results .12
8.6 Test report .12
9 Surface quality .12
9.1 Surface defects and intentional effects.12
9.2 Apparatus .12
9.3 Test specimens .13
9.4 Procedure .13
9.5 Expression of results .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.