EN ISO 10545-14:2015

SLOVENSKI STANDARD
01-december-2015
1DGRPHãþD
SIST EN ISO 10545-14:1998
.HUDPLþQHSORãþLFHGHO8JRWDYOMDQMHRGSRUQRVWLSURWLPDGHåHP,62

Ceramic tiles - Part 14: Determination of resistance to stains (ISO 10545-14:2015)
Keramische Fliesen und Platten - Teil 14: Bestimmung der Beständigkeit gegen
Fleckenbildner (ISO 10545-14:2015)
Carreaux et dalles céramiques - Partie 14 : Détermination de la résistance aux taches
(ISO 10545-14:2015)
Ta slovenski standard je istoveten z: EN ISO 10545-14:2015
ICS:
91.100.23 .HUDPLþQHSORãþLFH Ceramic tiles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 10545-14
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2015
EUROPÄISCHE NORM
ICS 91.100.23 Supersedes EN ISO 10545-14:1997
English Version
Ceramic tiles - Part 14: Determination of resistance to
stains (ISO 10545-14:2015)
Carreaux et dalles céramiques - Partie 14 : Keramische Fliesen und Platten - Teil 14: Bestimmung
Détermination de la résistance aux taches (ISO 10545- der Beständigkeit gegen Fleckenbildner (ISO 10545-
14:2015) 14:2015)
This European Standard was approved by CEN on 31 July 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10545-14:2015 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
European foreword
This document (EN ISO 10545-14:2015) has been prepared by Technical Committee ISO/TC 189
“Ceramic tile” in collaboration with Technical Committee CEN/TC 67 “Ceramic tiles” the secretariat of
which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2016, and conflicting national standards shall be
withdrawn at the latest by April 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 10545-14:1997.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10545-14:2015 has been approved by CEN as EN ISO 10545-14:2015 without any
modification.
INTERNATIONAL ISO
STANDARD 10545-14
Second edition
2015-09-15
Ceramic tiles —
Part 14:
Determination of resistance to stains
Carreaux et dalles céramiques —
Partie 14: Détermination de la résistance aux taches
Reference number
ISO 10545-14:2015(E)
©
ISO 2015
ISO 10545-14:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

ISO 10545-14:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative reference . 1
3 Principle . 1
4 Staining agents . 1
4.1 Stains leaving a trace (pastes) . 1
4.2 Stains having chemical/oxidizing action . 1
4.3 Stains forming a film . 1
5 Cleaning . 2
5.1 Cleaning agents . 2
5.2 Cleaning procedures and apparatus . 2
5.2.1 Procedure A . 2
5.2.2 Procedure B . 2
5.2.3 Procedure C . 2
5.2.4 Procedure D . . 2
5.3 Auxiliary apparatus . 3
6 Test specimens. 3
7 Procedure. 3
7.1 Application of the staining agent . 3
7.2 Attempts to remove stains . 3
8 Classification of results . 3
9 Test report . 4
Annex A (normative) Specifications for “green staining agent in light oil” .6
Annex B (normative) Specifications for “red staining agent in light oil” . 7
Annex C (normative) Example of preparation of test solutions . 8
ISO 10545-14:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 189, Ceramic tiles
This second edition cancels and replaces the first edition (ISO 10545-14:1995), which has been
technically revised. It also incorporates the Technical Corrigendum ISO 10545-14:1995/Cor.1:1997.
ISO 10545 consists of the following parts, under the general title Ceramic tiles:
— Part 1: Sampling and basis for acceptance
— Part 2: Determination of dimensions and surface quality
— Part 3: Determination of water absorption, apparent porosity, apparent relative density and bulk density
— Part 4: Determination of modulus of rupture and breaking strength
— Part 5: Determination of impact resistance by measurement of coefficient of restitution
— Part 6: Determination of resistance to deep abrasion for unglazed tiles
— Part 7: Determination of resistance to surface abrasion for glazed tiles
— Part 8: Determination of linear thermal expansion
— Part 9: Determination of resistance to thermal shock
— Part 10: Determination of moisture expansion
— Part 11: Determination of crazing resistance for glazed tiles
— Part 12: Determination of frost resistance
— Part 13: Determination of chemical resistance
— Part 14: Determination of resistance to stains
— Part 15: Determination of lead and cadmium given off by glazed tiles
iv © ISO 2015 – All rights reserved

ISO 10545-14:2015(E)
— Part 16: Determination of small colour differences
INTERNATIONAL STANDARD ISO 10545-14:2015(E)
Ceramic tiles —
Part 14:
Determination of resistance to stains
1 Scope
This part of ISO 10545 specifies a method for determining the resistance to stains of the proper surface
of ceramic tiles.
2 Normative reference
The following documents, in whole or in part, are normatively referenced in this document and a
...