EN ISO 2507-3:2017
(Main)Thermoplastics pipes and fittings - Vicat softening temperature - Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings (ISO 2507-3:1995)
Thermoplastics pipes and fittings - Vicat softening temperature - Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings (ISO 2507-3:1995)
Specifies the particular test conditions for determining the Vicat softening temperature of ABS and ASA pipes and fittings (the general test method is given in ISO 2507-1). Also gives, for information, the corresponding basic specifications.
Rohre und Formstücke aus Thermoplasten - Vicat-Erweichungstemperatur - Teil 3: Prüfbedingungen für Rohre und Formstücke aus Acrylnitril-Butadien-Styrol (ABS) und Acrylnitril-Styrol-Acrylester (ASA) (ISO 2507-3:1995)
Dieser Teil von ISO 2507 legt die spezifischen Testbedingungen zur Ermittlung der Vicat-Erweichungstemperatur von Rohren und Formstücken aus Acrylnitril-Butadien-Styrol (ABS) und Acrylnitril-Styrol-Acrylester (ASA) fest.
Außerdem sind zur Information die entsprechenden grundlegenden Festlegungen enthalten.
ANMERKUNG 1 Das allgemeine Prüfverfahren zur Ermittlung der Vicat-Erweichungstemperatur von Rohren und Formstücken aus Thermoplasten ist in ISO 2507-1 angegeben.
Tubes et raccords en matières thermoplastiques - Température de ramollissement Vicat - Partie 3: Conditions particulières d'essai pour tubes et raccords en acrylonitrile/butadiène/styrène (ABS) et en acrylonitrile/styrène/ester acrylique (ASA) (ISO 2507-3:1995)
L’IEC 60679-1:2017 spécifie les exigences générales relatives aux oscillateurs piézoélectriques, diélectriques et électrostatiques, y compris les oscillateurs à résonateur diélectrique (DRO - Dielectric Resonator Oscillators) et les oscillateurs à résonateurs à ondes acoustiques de volume à couches (FBAR) (ci-après dénommés "Oscillateur"), sous assurance qualité par les procédures d’agrément de savoir-faire ou les procédures d’homologation.
NOTE Les oscillateurs DRO et FBAR sont à l’étude.
Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) le titre a été modifié;
b) des éléments supplémentaires relatifs aux oscillateurs utilisant un résonateur OAS ou MEMS ont été ajoutés dans "Termes, définitions et informations générales";
c) les méthodes de mesure de l’IEC 60679-1:2007 ont été supprimées (elles seront intégrées à la série IEC 62884);
d) le contenu de l’Annexe A a été enrichi;
e) un nouveau terme et sa définition, “DIXO” (digital interfaced crystal oscillator - oscillateur à quartz à interface numérique), ont été ajoutés;
f) un nouveau terme et sa définition, “SSXO” (spread spectrum crystal oscillator - oscillateur à quartz à spectre étalé), ont été ajoutés;
g) l’Annexe D a été ajoutée.
Plastomerne cevi in fitingi - Temperatura zmehčišča po Vicatu - 3. del: Preskusni pogoji za cevi in fitinge iz akrilonitril/butadien/stirena (ABS) in akrilonitril/stiren/akril estra (ASA) (ISO 2507-3:1995)
Določa posebne preskusne pogoje za določevanje temperature zmehčišča Vicat cevi ter fitingov ABS in ASA (splošna preskusna metoda je podana v standardu ISO 2507-1). Podaja tudi ustrezne osnovne specifikacije za informativne namene.
General Information
- Status
- Published
- Publication Date
- 17-Oct-2017
- Withdrawal Date
- 30-Oct-2020
- Technical Committee
- CEN/TC 155 - Plastics piping systems and ducting systems
- Drafting Committee
- CEN/TC 155 - Plastics piping systems and ducting systems
- Current Stage
- 6060 - Definitive text made available (DAV) - Publishing
- Start Date
- 18-Oct-2017
- Due Date
- 30-Mar-2019
- Completion Date
- 18-Oct-2017
Relations
- Effective Date
- 08-Jun-2022
- Effective Date
- 21-Feb-2024
Overview
EN ISO 2507-3:2017 is a European and international standard specifying test conditions for determining the Vicat softening temperature (VST) of thermoplastic pipes and fittings made from acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA). Developed by ISO Technical Committee ISO/TC 138 and adopted by the European Committee for Standardization (CEN), this standard complements the general test method detailed in ISO 2507-1 by providing material-specific test parameters. It enables manufacturers and testing laboratories to assess the thermal softening behavior of ABS and ASA piping components accurately.
Key Topics
- Scope: Defines particular conditions for testing the Vicat softening temperature of ABS and ASA pipes and fittings, ensuring precise thermal property evaluation tailored to these materials.
- Testing Method: Describes the use of an oven heating method (substituting the general heating bath) to condition test pieces, following guidelines from ISO 2507-1 for consistent procedure adoption.
- Test Specimens: Specifies requirements for test pieces preparation and conditioning, including preliminary drying at 90°C and stabilization at standard laboratory conditions (23°C ± 2°C and 50% ± 5% relative humidity).
- Test Reporting: Recommends standardized reporting formats aligned with ISO 2507-1, facilitating clear communication of Vicat softening temperature results.
- Basic Specifications: Provides informative annexes outlining minimum Vicat softening temperature thresholds of 90°C for ABS and ASA pipes and fittings, with allowance for more stringent values per specific product standards.
- Normative References: Relies on ISO 2507-1 as the normative basis for the general test method, ensuring coherence across related testing procedures.
Applications
EN ISO 2507-3:2017 is essential for quality control and material certification in industries that utilize ABS and ASA thermoplastic pipes and fittings, including:
- Building and Construction: Ensuring reliable thermal resistance of piping systems used in plumbing, drainage, and HVAC applications.
- Automotive and Transportation: Verifying material performance in vehicle fluid transport systems subjected to temperature variations.
- Industrial Fluid Handling: Assessing suitability of ABS and ASA pipes for chemical transport and process piping where heat resistance is critical.
- Manufacturing and R&D: Supporting product development through precise thermal property measurements, facilitating material selection and component design.
By adhering to this standard, manufacturers can guarantee consistent product performance, comply with regulatory requirements, and reduce risks associated with thermal deformation.
Related Standards
- ISO 2507-1: General test method for Vicat softening temperature determination of thermoplastic pipes and fittings.
- EN ISO 2507-2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), and high-impact resistant poly(vinyl chloride) (PVC-HI) pipes and fittings.
- EN 727:1994: The superseded version of the standard, replaced by EN ISO 2507-3:2017.
- Product-Specific Standards: Individual standards that specify minimum Vicat softening temperature requirements exceeding the baseline 90°C for ABS and ASA piping systems.
Keywords: EN ISO 2507-3, Vicat softening temperature, ABS pipes, ASA pipes, thermoplastics testing, plastic pipe standards, thermal softening test, thermostability, plastic fittings, European standards for plastics, ISO plastics testing, thermoplastic pipe quality, CEN standards for ABS and ASA
Frequently Asked Questions
EN ISO 2507-3:2017 is a standard published by the European Committee for Standardization (CEN). Its full title is "Thermoplastics pipes and fittings - Vicat softening temperature - Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings (ISO 2507-3:1995)". This standard covers: Specifies the particular test conditions for determining the Vicat softening temperature of ABS and ASA pipes and fittings (the general test method is given in ISO 2507-1). Also gives, for information, the corresponding basic specifications.
Specifies the particular test conditions for determining the Vicat softening temperature of ABS and ASA pipes and fittings (the general test method is given in ISO 2507-1). Also gives, for information, the corresponding basic specifications.
EN ISO 2507-3:2017 is classified under the following ICS (International Classification for Standards) categories: 23.040.20 - Plastics pipes; 23.040.45 - Plastics fittings. The ICS classification helps identify the subject area and facilitates finding related standards.
EN ISO 2507-3:2017 has the following relationships with other standards: It is inter standard links to EN 727:1994, FprEN ISO 2507. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN ISO 2507-3:2017 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2018
1DGRPHãþD
SIST EN 727:1997
3ODVWRPHUQHFHYLLQILWLQJL7HPSHUDWXUD]PHKþLãþDSR9LFDWXGHO 3UHVNXVQL
SRJRML]DFHYLLQILWLQJHL]DNULORQLWULOEXWDGLHQVWLUHQD $%6 LQ
DNULORQLWULOVWLUHQDNULOHVWUD $6$ ,62
Thermoplastics pipes and fittings - Vicat softening temperature - Part 3: Test conditions
for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA)
pipes and fittings (ISO 2507-3:1995)
Rohre und Formstücke aus Thermoplasten - Vicat-Erweichungstemperatur - Teil 3:
Prüfbedingungen für Rohre und Formstücke aus Acrylnitril-Butadien-Styrol (ABS) und
Acrylnitril-Styrol-Acrylester (ASA) (ISO 2507-3:1995)
Tubes et raccords en matières thermoplastiques - Température de ramollissement Vicat
- Partie 3: Conditions particulières d'essai pour tubes et raccords en
acrylonitrile/butadiène/styrène (ABS) et en acrylonitrile/styrène/ester acrylique (ASA)
(ISO 2507-3:1995)
Ta slovenski standard je istoveten z: EN ISO 2507-3:2017
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 2507-3
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2017
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45 Supersedes EN 727:1994
English Version
Thermoplastics pipes and fittings - Vicat softening
temperature - Part 3: Test conditions for
acrylonitrile/butadiene/styrene (ABS) and
acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings
(ISO 2507-3:1995)
Tubes et raccords en matières thermoplastiques - Rohre und Formstücke aus Thermoplasten - Vicat-
Température de ramollissement Vicat - Partie 3: Erweichungstemperatur - Teil 3: Prüfbedingungen für
Conditions particulières d'essai pour tubes et raccords Rohre und Formstücke aus Acrylnitril-Butadien-Styrol
en acrylonitrile/butadiène/styrène (ABS) et en (ABS) und Acrylnitril-Styrol-Acrylester (ASA) (ISO
acrylonitrile/styrène/ester acrylique (ASA) (ISO 2507- 2507-3:1995)
3:1995)
This European Standard was approved by CEN on 19 September 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2507-3:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 2507-3:1995 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes,
fittings and valves for the transport of fluids” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 2507-3:2017 by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be
withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 727:1994.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 2507-3:1995 has been approved by CEN as EN ISO 2507-3:2017 without any
modification.
INTERNATIONAL
ISO
STANDARD
2507-3
First edition
1995-02-15
Thermoplastics pipes and fittings -
Vicat softening temperature -
Part 3:
Test conditions for
acrylonitrile/butadiene/styrene (ABS) and
acrylonitri
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...