EN 13445-3:2002/A3:2007
(Amendment)Unfired pressure vessels - Part 3: Design
Unfired pressure vessels - Part 3: Design
Design by formula (alternative design factor).
Alternative Design By Formulae method considering a reduced safety factor on tensile strength in order to reduce thicknesses (the so called Alternative Route)
Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Récipients sous pression non soumis à la flamme - Partie 3: Conception
Neogrevane tlačne posode - 3. del: Konstruiranje
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2009
1HRJUHYDQHWODþQHSRVRGHGHO.RQVWUXLUDQMH
Unfired pressure vessels - Part 3: Design
Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Récipients sous pression non soumis a la flamme - Partie 3: Conception
Ta slovenski standard je istoveten z: EN 13445-3:2002/A3:2007
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 13445-3:2002/A3
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2007
ICS 23.020.30
English Version
Unfired pressure vessels - Part 3: Design
Récipients sous pression non soumis à la flamme - Partie Unbefeuerte Druckbehälter - Teil 3: Konstruktion
3: Conception
This amendment A3 modifies the European Standard EN 13445-3:2002; it was approved by CEN on 29 December 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-3:2002/A3:2007: E
worldwide for CEN national Members.
Contents Page
Foreword.3
6.2 Steels (except castings) other than austenitic steels covered by 6.4 and 6.5 .4
6.3 Alternative route for steels (except castings) other than austenitic steels covered by 6.4
and 6.5.4
6.3.1 Normal operating load cases.4
6.3.2 Testing load cases.4
6.4 Austenitic steels (except castings) with a minimum rupture elongation, as given in the
relevant technical specification for the material, greater than 30 % up to 35 %.5
6.4.1 Normal operating load cases.5
6.4.2 Testing load cases.5
6.5 Austenitic steels (except castings) with a minimum rupture elongation, as given in the
relevant technical specification for the material, greater than 35 %.5
6.5.1 Normal operating load cases.5
6.5.2 Testing load cases.5
6.6 Cast Steels.5
Foreword
This document (EN 13445-3:2002/A3:2007) has been prepared by Technical Committee CEN/TC 54 “Unfired
pressure vessels”, the secretariat of which is held by BSI.
This Amendment to the European Standard EN 13445-3:2002 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by October 2007, and conflicting
national standards shall be withdrawn at the latest by October 2007.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.