EN 13482:2013

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.LMDGummischläuche und -schlauchleitungen für Asphalt und Bitumen - SpezifikationTuyaux et flexibles en caoutchouc pour asphalte et bitume - SpécificationRubber hoses and hose assemblies for asphalt and bitumen - Specification83.140.40Gumene ceviHosesICS:Ta slovenski standard je istoveten z:EN 13482:2013SIST EN 13482:2014en,fr,de01-maj-2014SIST EN 13482:2014SLOVENSKI
STANDARDSIST EN 13482:20021DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13482
October 2013 ICS 23.040.70 Supersedes EN 13482:2001English Version
Rubber hoses and hose assemblies for asphalt and bitumen - Specification
Tuyaux et flexibles en caoutchouc pour asphalte et bitume -Spécification
Gummischläuche und -schlauchleitungen für Asphalt und Bitumen - Spezifikation This European Standard was approved by CEN on 7 September 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13482:2013: ESIST EN 13482:2014

Test method for change in length at proof pressure .9 A.1 Test medium and temperature .9 A.2 Procedure .9 Annex B (normative)
Test method for bend and burst pressure . 10 Annex C (normative)
Type and routine tests . 11 Annex D (informative)
Recommended test frequency for production acceptance tests . 12 Annex E (informative)
Environmental checklist . 13 Bibliography . 15
1 Scope This European Standard specifies requirements for two types of hose and hose assembly (Type 1 and Type 2) identified by their maximum working pressures (Type
1 7 bar and Type 2 15 bar) and main use, i.e. Type 1 is for road and rail tanker use and Type 2 is for dockside use. The types are further divided into two classes related to the maximum temperature of the product to be conveyed (Class A up to 175 °C and Class B up to 200 °C). The hose constructions may be smooth bore (SB) or rough bore (RB). NOTE These types of hose or hose assemblies are not necessarily suitable for all types of petroleum based products or coal tar, or products containing coal tar. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 14023, Bitumen and bituminous binders - Specification framework for polymer modified bitumens EN ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671) EN ISO 7233:2008, Rubber and plastics hoses and hose assemblies — Determination of resistance to vacuum (ISO 7233:2006) EN ISO 7326, Rubber and plastics hoses — Assessment of ozone resistance under static conditions (ISO 7326) EN ISO 8031, Rubber and plastics hoses and hose assemblies — Determination of electrical resistance and conductivity (ISO 8031) EN ISO 8330:2008, Rubber and plastics hoses and hose assemblies – Vocabulary (ISO 8330:2007) EN ISO 10619-1, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 1: Bending tests at ambient temperature (ISO 10619-1) ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties ISO 4649:2010, Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 8330:2008 apply. 4 Classification Hoses and hose assemblies shall be one of the following types: Type 1 maximum working pressure 7 bar for road and rail tanker hose and hose assemblies; Type 2 maximum working pressure 15 bar for dockside hose and hose assemblies. Each type shall be available in SB or RB construction and these additional letters shall be part of the identification. SIST EN 13482:2014

 an ozone resistant rubber cover of minimum thickness 2,0 mm. Internally, hoses shall have rubber linings that are smooth and free from delamination and blisters. 5.2 Type 1 and Type 2 hoses — rubber rough bore (RB) These hoses shall have the following construction:
 an internal steel wire helix of flat or round cross-section;  a synthetic rubber and/or textile lining matrix;  reinforcing plies of textile or steel wire;  additional helix reinforcement, if specified; and  an ozone resistant rubber cover of minimum thickness 2,0 mm. Overlapped joins in the lining matrix above the internal wire helix may be visible between the pitch of the helix. 5.3 End fittings End fittings for all hose assemblies shall be of one of the following types. a) ‘Built-in’ during manufacture of the hose. b) ‘Swaged-on’, either internally or externally according to the manufacturer’s design, after manufacture of the hose. c) ‘Clamped-on’ after manufacture of the hose. ‘Clamped-on’ fittings are NOT recommended for dockside hoses. For each type of end connection to the hose, an assembly type test shall be carried out, in accordance with 8.2. SIST EN 13482:2014

Nominal Inside
Tolerances Minimum bend radius bore diameter
Smooth bore hoses Rough bore hoses
mm mm mm mm 50 50 ± 0,6 275 485 51 51 ± 0,6 280 495 63 63 ± 0,6 345 502 65 65 ± 0,6 350 510 75 75 ± 0,8 450 600 76 76 ± 0,8 456 608 100 100 ± 1,2 600 750 101 101 ± 1,2 606 758 125 125 ± 1,6 730 880 127 127 ± 1,6 742 894 150 150 ± 2,0 850 1 000 152 152 ± 2,0 861 1 013 200 200 ± 2,0 1 100 1 250 203 203 ± 2,0 1 117 1 269
6.2 Lengths and tolerances The finished length of a hose assembly shall have a tolerance of + 2 % to - 1 % of the ordered length, after conclusion of the pressure test. Special short lengths, distance pieces etc., may not be able to be bent to the minimum radii as specified in Table 1. The purchaser should agree requirements of lengths less than 2 m with the manufacturer. 6.3 Concentricity When measured in accordance with EN ISO 4671, the concentricity based on a total indicator reading shall be
1,0 mm for hoses of nominal bore 50 to 76 inclusive and 1,5 mm for hoses of nominal bore 100 to 203 inclusive. SIST EN 13482:2014
...