EN 12059:2008+A1:2011
(Main + Amendment)Natural stone products - Dimensional stone work - Requirements
Natural stone products - Dimensional stone work - Requirements
This European Standard specifies requirements for the following stone units:
a) Structural solid stone units:
i. Load bearing stone elements, typically subject to prevailing compression stresses, such as solid columns, arches and similar;
ii. Solid stone elements used for parapets, handrails, balustrades, copings and the like, intended to withstand horizontal live loadings in addition to any dead load.
b) Finishing solid stone units:
i. Curved cladding panels, for the external finishing of walls, columns or pilasters;
ii. Stone elements for framing one or more side openings in building walls or floors, such as sills, jambs, architraves and similar.
This European Standard does not include stone masonry units, as defined in EN 771-6, stone which is a ‘cast-on’ finish to pre-cast concrete or agglomerated stones. Moreover it does not cover commemorative or funeral stones and sculptures, when they do not show the above mentioned characteristics.
Natursteinprodukte - Steine für Massivarbeiten - Anforderungen
Diese Europäische Norm legt Anforderungen an die folgenden Steinelemente fest: a) Strukturelle feste Steinelemente. i) Lasttragende Steinelemente, üblicherweise den maßgeblichen Druckspannungen ausgesetzt, wie feste Säulen, Bögen und ähnliches; ii) Feste Steinelemente für Brüstungen, Handläufe, Balustraden, Mauerabdeckungen und ähnliches, die zusätzlich zu jeglichen Eigenlasten horizontalen Nutzlasten widerstehen müssen. b) Abschließende feste Steinelemente. i) Gekrümmte Bekleidungsplatten für die Außenbekleidung von Wänden, Säulen oder Wandpfeilern; ii) Steinelemente zur Rahmung einer oder mehrerer Seitenöffnungen in Gebäudewänden oder -decken, wie Schwellen, aufrechte Rahmenteile, Sockel und ähnliches. Diese Europäische Norm gilt nicht für Steinelemente für Mauerwerk, wie in EN 771-6 definiert, Gestein als „angegossene“ Oberfläche von Fertigbeton, oder Gesteinskörnungen. Sie gilt auch nicht für Denkmale und Grabsteine und Skulpturen, wenn sie nicht die oben genannten Merkmale aufweisen.
Produits en pierre naturelle - Pierre de taille - Exigences
La présente Norme européenne fixe les exigences relatives aux éléments de pierre suivants :
a) Éléments de construction massifs en pierre :
i) Éléments porteurs en pierre, généralement soumis à des contraintes en compression, tels que colonnes
et arches massives, par exemple ;
ii) Éléments massifs en pierre, utilisés pour les parapets, mains courantes, balustrades, couronnements et autres
éléments similaires, destinés à résister à des charges horizontales sous tension, en plus de tout poids mort.
b) Éléments de finition massifs en pierre :
i) Panneaux cintrés de revêtement attaché, pour la finition extérieure de murs, colonnes ou pilastres ;
ii) Éléments en pierre utilisés pour encadrer une ou plusieurs ouvertures latérales dans des planchers ou murs
de construction, tels que seuils, huisseries, chambranles et autres éléments similaires.
La présente Norme européenne n’inclut ni les éléments de maçonnerie en pierre définis dans l’EN 771-6, ni les
pierres sous forme de finition moulée sur du béton précontraint, ni les pierres agglomérées. Elle ne couvre pas non
plus les sculptures et pierres funéraires ou commémoratives lorsqu’elles ne présentent pas les caractéristiques
mentionnées plus haut.
Proizvodi iz naravnega kamna - Dimenzijsko obdelan kamen - Zahteve
Ta evropski standard določa zahteve za naslednje zidake iz kamna:
a) konstrukcijski zidaki iz trdnega kamna:
i. nosilni elementi iz kamna, ki so običajno izpostavljeni prevladujočim tlačnim napetostim, kot so trdni stebri, oboki in podobno;
ii. elementi iz trdnega kamna, ki se uporabljajo za parapete, ograje, ograje iz stebričkov, strešne dodatke in podobne konstrukcije, ki morajo poleg lastne teže prenašati tudi vodoravne koristne obremenitve poleg lastne teže.
b) zaključni zidaki iz trdnega kamna:
i. ukrivljeni fasadni paneli za zunanjo zaključno obdelavo zidov, stebrov ali pilastrov;
ii. elementi iz kamna za uokvirjanje ene ali več stranskih odprtin pri grajenju zidov ali tal, kot so pragovi, podboji, arhitravi in podobni elementi.
Ta evropski standard ne zajema zidakov iz kamna iz standarda EN 771-6, ki opisuje kamen kot »nalito« zaključno obdelavo predizdelanega betonskega ali aglomeliranega kamna. Poleg tega ne zajema kamna za spomenike ali nagrobnike in skulpture, kadar nimajo zgoraj navedenih značilnosti.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Proizvodi iz naravnega kamna - Dimenzijsko obdelan kamen - ZahteveNatursteinprodukte - Steine für Massivarbeiten - AnforderungenProduits en pierre naturelle - Pierre de taille - ExigencesNatural stone products - Dimensional stone work - Requirements91.100.15Mineralni materiali in izdelkiMineral materials and productsICS:Ta slovenski standard je istoveten z:EN 12059:2008+A1:2011SIST EN 12059:2008+A1:2012en,fr,de01-februar-2012SIST EN 12059:2008+A1:2012SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12059:2008+A1
December 2011 ICS 91.100.15 Supersedes EN 12059:2008English Version
Natural stone products - Dimensional stone work - Requirements
Produits en pierre naturelle - Pierre de taille - Exigences
Natursteinprodukte - Steine für Massivarbeiten - Anforderungen This European Standard was approved by CEN on 12 January 2008 and includes Amendment 1 approved by CEN on 13 November 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12059:2008+A1:2011: ESIST EN 12059:2008+A1:2012
Sampling . 14A.1General . 14A.2Principles of sampling . 14A.3Taking bulk samples . 14A.4Preparing a sampling plan . 14A.5Sampling apparatus . 15A.6Sampling methods . 15A.6.1General . 15A.6.2Sampling from quarries . 15A.6.3Sampling from plants . 16A.6.4Sampling from buildings . 16A.7Marking, packaging and dispatch of the samples . 16A.8Sampling report . 16Bibliography . 18 SIST EN 12059:2008+A1:2012
a) Structural solid stone units: i. Load bearing stone elements, typically subject to prevailing compression stresses, such as solid columns, arches and similar; ii. Solid stone elements used for parapets, handrails, balustrades, copings and the like, intended to withstand horizontal live loadings in addition to any dead load. b) Finishing solid stone units: i. Curved cladding panels, for the external finishing of walls, columns or pilasters; ii. Stone elements for framing one or more side openings in building walls or floors, such as sills, jambs, architraves and similar. This European Standard does not include stone masonry units, as defined in EN 771-6, stone which is a ‘cast-on’ finish to pre-cast concrete or agglomerated stones. Moreover it does not cover commemorative or funeral stones and sculptures, when they do not show the above mentioned characteristics. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. !EN 772-1, Methods of test for masonry units — Part 1: Determination of compressive strength" EN 1925, Natural stone test methods — Determination of water absorption coefficient by capillarity EN 1926, Natural stone test methods — Determination of uniaxial compressive strength EN 1936, Natural stone test methods — Determination of real density and apparent density, and of total and open porosity EN 12371, Natural stone test methods — Determination of frost resistance EN 12372, Natural stone test methods — Determination of flexural strength under concentrated load EN 12407, Natural stone test methods — Petrographic examination EN 12440, Natural stone — Denomination criteria EN 12670:2001, Natural stone — Terminology EN 13161, Natural stone test methods — Determination of flexural strength under constant moment EN 13373:2003, Natural stone test methods — Determination of geometric characteristics on units EN 13501-1, Fire classification of construction products and building elements — Part 1: Classification using data from reaction to fire tests EN 13755, Natural stone test methods — Determination of water absorption at atmospheric pressure SIST EN 12059:2008+A1:2012
Tolerance
More than 15 up to and including 30 ± 10 % a More than 30 up to and including 80 ± 3 mm b More than 80 ± 5 mm c a in case of elements to be assembled the tolerance of the visual thickness shall become respectively ± 0,5 mm b in case of elements to be assembled the tolerance of the visual thickness shall become respectively ± 1 mm c in case of elements to be assembled the tolerance of the visual thickness shall become respectively ± 2 mm
Stricter tolerances may be declared by the supplier. SIST EN 12059:2008+A1:2012
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.