EN ISO 25649-2:2017

SLOVENSKI STANDARD
01-december-2017
1DGRPHãþD
SIST EN 15649-2:2010+A2:2013
3ODYDMRþLSULSRPRþNL]DSURVWLþDVNLVHXSRUDEOMDMRQDYRGLLQYQMHMGHO
,QIRUPDFLMH]DSRWURãQLND,62
Floating leisure articles for use on and in the water - Part 2: Consumer information (ISO
25649-2:2017)
Schwimmende Freizeitartikel zum Gebrauch auf und im Wasser - Teil 2:
Verbraucherinformation (ISO 25649-2:2017)
Articles de loisirs flottants à utiliser sur ou dans l'eau - Partie 2 : Information des
consommateurs (ISO 25649-2:2017)
Ta slovenski standard je istoveten z: EN ISO 25649-2:2017
ICS:
97.220.40 Oprema za športe na Outdoor and water sports
prostem in vodne športe equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 25649-2
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2017
EUROPÄISCHE NORM
ICS 97.220.40; 97.020 Supersedes EN 15649-2:2009+A2:2013
English Version
Floating leisure articles for use on and in the water - Part
2: Consumer information (ISO 25649-2:2017)
Articles de loisirs flottants à utiliser sur ou dans l'eau - Schwimmende Freizeitartikel zum Gebrauch auf und
Partie 2: Informations aux consommateurs (ISO im Wasser - Teil 2: Verbraucherinformation (ISO
25649-2:2017) 25649-2:2017)
This European Standard was approved by CEN on 24 June 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25649-2:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 25649-2:2017) has been prepared by Technical Committee ISO/TC 83 “Sports
and other recreational facilities and equipment” in collaboration with Technical Committee
CEN/TC 136 “Sports, playground and other recreational facilities and equipment” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be
withdrawn at the latest by April 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15649-2:2009+A2:2013.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 25649-2:2017 has been approved by CEN as EN ISO 25649-2:2017 without any
modification.
INTERNATIONAL ISO
STANDARD 25649-2
First edition
2017-08
Floating leisure articles for use on and
in the water —
Part 2:
Consumer information
Articles de loisirs flottants à utiliser sur ou dans l'eau —
Partie 2: Informations aux consommateurs
Reference number
ISO 25649-2:2017(E)
©
ISO 2017
ISO 25649-2:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 25649-2:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Consumer information . 1
4.1 General . 1
4.2 Consumer information at point of sale (information before buying) . 2
4.2.1 General. 2
4.2.2 General information to be provided . 2
4.3 Information related to preparation for use . 2
4.4 Information related to maintenance, repair and storage . 2
5 Requirements related to printing . 2
5.1 General . 2
5.2 Durability of printings on the product . 2
5.3 Language and letter size for plain text information on the product . 3
5.3.1 Requirements . 3
5.3.2 Testing . 3
6 Product safety label . 3
6.1 General . 3
6.2 Supplementary safety information symbol . 3
6.2.1 Supplementary safety information symbols related to warnings . 3
6.2.2 Supplementary safety information symbols related to prohibition . 4
6.2.3 Supplementary safety information symbols related to mandatory instruction . 7
6.3 Safety sign .11
6.4 Position of supplementary safety information symbol and safety sign .12
6.5 Colour of supplementary safety information symbols and safety sign .12
6.6 Size of supplementary safety information symbol and safety sign .12
6.7 Allocation of the supplementary safety information symbols .13
7 Instructions .17
7.1 General .17
7.2 Safety information .17
8 Mislabelling.17
Annex A (informative) Array of supplementary safety information symbols and safety
signs (Example) .18
Bibliography .22
ISO 25649-2:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
ISO 25649-2 was prepared by the European Committee Standardization (CEN) Technical Committee
CEN/TC 136, Spo
...