EN ISO 11623:2015
(Main)Gas cylinders - Composite construction - Periodic inspection and testing (ISO 11623:2015, Corrected version 2017-02)
Gas cylinders - Composite construction - Periodic inspection and testing (ISO 11623:2015, Corrected version 2017-02)
ISO 11623:2015 specifies the requirements for periodic inspection and testing and to verify the integrity for further service of hoop-wrapped and fully-wrapped composite transportable gas cylinders, with aluminium-alloy, steel or non-metallic liners or of linerless construction (Types 2, 3, 4, and 5), intended for compressed, liquefied or dissolved gases under pressure, of water capacity from 0,5 l up to 450 l.
ISO 11623:2015 is written to address the periodic inspection and testing of composite cylinders constructed to ISO 11119‑1, ISO 11119‑2, and ISO 11119‑3 standards and can be applied to other composite cylinders designed to comparable standards when authorized by the competent authority.
As far as practicable, this International Standard also can be applied to cylinders of less than 0,5 l water capacity.
Gasflaschen - Verbundbauweise (Composite-Bauweise) - Wiederkehrende Inspektion und Prüfung (ISO 11623:2015, korrigierte Fassung 2017-02)
Diese Internationale Norm legt die Anforderungen an die wiederkehrende Inspektion und Prüfung von umfangs- und vollumwickelten ortsbeweglichen Gasflaschen aus Verbundwerkstoffen (Composite-Flaschen) mit Linern aus Aluminiumlegierungen, Stahl oder nichtmetallischen Werkstoffen oder Flaschenbauweisen ohne Liner mit einem Fassungsraum von 0,5 l bis 450 l fest, welche zur Verwendung mit verdichteten, verflüssigten oder unter Druck gelösten Gasen vorgesehen sind.
Diese Norm wurde geschrieben, um die wiederkehrende Inspektion und Prüfung von nach ISO 11119-1, ISO 11119-2 und ISO 11119-3 ausgelegten Composite-Flaschen zu beschreiben und darf mit Genehmigung der zuständigen Behörde auch für nach vergleichbaren Normen ausgelegte Composite-Flaschen angewendet werden.
Soweit möglich, darf diese Internationale Norm auch für Flaschen mit einem Fassungsraum kleiner als 0,5 l angewendet werden.
Diese Internationale Norm legt die Anforderungen an die wiederkehrende Inspektion und Prüfung fest, um die Unversehrtheit solcher Gasflaschen für den weiteren Betrieb zu überprüfen.
Bouteilles à gaz - Construction composite - Contrôles et essais périodiques (ISO 11623:2015, Version corrigée 2017-02)
ISO 11623:2015 spécifie les exigences relatives au contrôle et essais périodiques des bouteilles à gaz en matériau composite transportables, frettées ou entièrement bobinées, dotées ou non d'un liner en alliage d'aluminium, en acier ou non-métallique (Types 2, 3, 4, et 5), destinées à contenir des gaz comprimés, liquéfiés ou dissous sous pression et ayant une capacité en eau comprise entre 0,5 l et 450 l inclus, ainsi que la vérification de leur intégrité pour leur maintien en service.
ISO 11623:2015 est élaborée afin de couvrir les contrôles et essais périodiques des bouteilles gaz en matériau composite construites conformément aux normes ISO 11119‑1, ISO 11119‑2, et ISO 11119‑3 et peut être étendue à d'autres bouteilles en matériau composite conçues conformément à des normes comparables lorsque l'autorité compétente l'autorise.
Dans la mesure du possible, la présente Norme internationale peut également être appliquée aux bouteilles ayant une capacité inférieure à 0,5 l.
Plinske jeklenke - Kompozitni materiali - Periodični pregledi in preskusi (ISO 11623:2015)
Ta mednarodni standard opredeljuje zahteve za periodične preglede in preskuse ter preverjanje celovitosti za namen nadaljnje uporabe premičnih jeklenk za plin, obročasto in popolnoma obvitih s kompozitno maso, s tuljavami iz aluminijeve zlitine, jekla ali materiala, ki ni kovina, ali s konstrukcijo brez tuljav (tipi 2, 3, 4 in 5), ki so namenjeni za stisnjene, utekočinjene ali raztopljene pline pod tlakom, s prostornino vode od 0,5 do 450 l.
Ta mednarodni standard obravnava periodične preglede in preskuse kompozitnih jeklenk, izdelanih v skladu s standardi ISO 11119-1, ISO 11119-2 in ISO 11119-3, pri čemer ga je mogoče uporabiti za druge kompozitne jeklenke, zasnovane v skladu s primerljivimi standardi, če to odobri pristojni organ. V smislu praktičnosti je mogoče ta mednarodni standard uporabiti za jeklenke s prostornino vode, manjšo od 0,5 l.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2016
1DGRPHãþD
SIST EN ISO 11623:2002
3OLQVNHMHNOHQNH.RPSR]LWQLPDWHULDOL3HULRGLþQLSUHJOHGLLQSUHVNXVL ,62
Gas cylinders - Composite construction - Periodic inspection and testing (ISO
11623:2015)
Gasflaschen - Verbundbauweise - Wiederkehrende Inspektion und Prüfung (ISO
11623:2015)
Bouteilles à gaz transportables - Contrôles et essais périodiques des bouteilles à gaz en
matériau composite (ISO 11623:2015)
Ta slovenski standard je istoveten z: EN ISO 11623:2015
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 11623
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2015
EUROPÄISCHE NORM
ICS 23.020.30 Supersedes EN ISO 11623:2002
English Version
Gas cylinders - Composite construction - Periodic
inspection and testing (ISO 11623:2015)
Bouteilles à gaz - Construction composite - Contrôles et Gasflaschen - Verbundbauweise - Wiederkehrende
essais périodiques (ISO 11623:2015) Inspektion und Prüfung (ISO 11623:2015)
This European Standard was approved by CEN on 3 October 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11623:2015 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 11623:2015) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be
withdrawn at the latest by June 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 11623:2002.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11623:2015 has been approved by CEN as EN ISO 11623:2015 without any modification.
INTERNATIONAL ISO
STANDARD 11623
Second edition
2015-12-01
Gas cylinders — Composite
construction — Periodic inspection
and testing
Bouteilles à gaz — Construction composite — Contrôles et essais
périodiques
Reference number
ISO 11623:2015(E)
©
ISO 2015
ISO 11623:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
ISO 11623:2015(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Due dates for periodic inspection and testing . 4
5 Procedures for periodic inspection and testing . 4
5.1 List of procedures . 4
5.2 Heat exposure . 4
6 Identification of cylinder and preparation for periodic inspection and testing .5
7 External visual inspection . 5
7.1 Preparation . 5
7.2 Inspection procedures . 6
7.3 Damage . 6
7.3.1 General. 6
7.3.2 Identification label . 6
7.3.3 Damage levels . 6
7.3.4 Types of damage . 8
7.4 Repairs . 9
8 Internal visual inspection .10
8.1 Safe removal of valve .10
8.2 Internal inspection and cleaning .10
8.2.1 General.10
8.2.2 Metallic liners .10
8.2.3 Linerless and non-metallic liners .10
8.3 Inspection of cylinder neck/shoulder .11
9 Pressure test .12
10 Leak test .12
11 Inspection of valve .12
12 Final operations .12
12.1 Drying and cleaning .12
12.2 Painting .12
12.3 Cylinder re-valving .13
12.4 Check on cylinder tare .13
12.5 Marking .13
12.6 Reference to next test date .13
12.7 Identification of contents .14
12.8 Records .14
13 Rejection and rendering cylinders unserviceable .14
Annex A (normative) Damage criteria for steel wire wound, aluminium-alloy cylinders .22
Annex B (normative) Internal inspection of translucent cylinders .23
Annex C (informative) Intervals between periodic inspection and testing .24
Bibliography .27
ISO 11623:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organization
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.