EN ISO 13262:2017

SLOVENSKI STANDARD
01-januar-2018
1DGRPHãþD
SIST EN 1979:2000
Plastomerni cevni sistemi za odpadno vodo in kanalizacijo, položeni v zemljo, ki
delujejo po težnostnem principu - Plastomerne cevi s spiralno strukturirano steno
cevi - Ugotavljanje nateznih trdnosti spojev (ISO 13262:2010)
Thermoplastics piping systems for non-pressure underground drainage and sewerage -
Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile
strength of a seam (ISO 13262:2010)
Erdverlegte Rohrleitungssysteme aus Thermoplasten für Abwasserkanäle und -leitungen
- Thermoplastische Spiralrohre mit profilierter Wandung - Bestimmung der Zugfestigkeit
einer Verbindungsnaht (ISO 13262:2010)
Systèmes de canalisations thermoplastiques pour branchements et collecteurs
d'assainissement enterrés sans pression - Tubes thermoplastiques à paroi structurée
enroulés en hélice - Détermination de la résistance en traction de la ligne de soudure
(ISO 13262:2010)
Ta slovenski standard je istoveten z: EN ISO 13262:2017
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 13262
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2017
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 91.140.80; 93.030 Supersedes EN 1979:1999
English Version
Thermoplastics piping systems for non-pressure
underground drainage and sewerage - Thermoplastics
spirally-formed structured-wall pipes - Determination of
the tensile strength of a seam (ISO 13262:2010)
Systèmes de canalisations thermoplastiques pour Erdverlegte Rohrleitungssysteme aus Thermoplasten
branchements et collecteurs d'assainissement enterrés für Abwasserkanäle und -leitungen - Thermoplastische
sans pression - Tubes thermoplastiques à paroi Spiralrohre mit profilierter Wandung - Bestimmung
structurée enroulés en hélice - Détermination de la der Zugfestigkeit einer Verbindungsnaht (ISO
résistance en traction de la ligne de soudure (ISO 13262:2010)
13262:2010)
This European Standard was approved by CEN on 19 September 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13262:2017 E
worldwide for CEN national Members.

Contents Page
European Foreword . 3

European Foreword
The text of ISO 13262:2010 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes,
fittings and valves for the transport of fluids” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 13262:2017 by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2018 and conflicting national standards shall be
withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1979:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 13262:2010 has been approved by CEN as a EN ISO 13262:2017 without any
modification.
INTERNATIONAL ISO
STANDARD 13262
First edition
2010-05-15
Thermoplastics piping systems for non-
pressure underground drainage and
sewerage — Thermoplastics spirally-
formed structured-wall pipes —
Determination of the tensile strength of a
seam
Systèmes de canalisations thermoplastiques pour branchements et
collecteurs d'assainissement enterrés sans pression — Tubes
thermoplastiques à paroi structurée enroulés en hélice — Détermination
de la résistance en traction de la ligne de soudure

Reference number
ISO 13262:2010(E)
©
ISO 2010
ISO 13262:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
...