CEN ISO/TS 19392-6:2026

SLOVENSKI STANDARD
01-maj-2026
Nadomešča:
SIST-TS CEN ISO/TS 19392-6:2024
Barve in laki - Premazni sistemi za lopatice rotorjev vetrnih turbin - 6. del:
Ugotavljanje in vrednotenje oprijema ledu z uporabo centrifuge (ISO/TS 19392-
6:2026)
Paints and varnishes - Coating systems for wind-turbine rotor blades - Part 6:
Determination and evaluation of ice adhesion using centrifuge (ISO/TS 19392-6:2026)
Beschichtungsstoffe - Beschichtungssysteme für Rotorblätter von Windenergieanlagen -
Teil 6: Bestimmung und Bewertung der Eisadhäsion mittels Zentrifuge (ISO/TS 19392-
6:2026)
Peintures et vernis - Matériaux de revêtement pour pales de turbines éoliennes - Partie
6: Détermination et évaluation de l'adhésion de la glace à l'aide d'une centrifugeuse
(ISO/TS 19392-6:2026)
Ta slovenski standard je istoveten z: CEN ISO/TS 19392-6:2026
ICS:
27.180 Vetrne elektrarne Wind turbine energy systems
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

CEN ISO/TS 19392-6
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
February 2026
TECHNISCHE SPEZIFIKATION
ICS 87.040 Supersedes CEN ISO/TS 19392-6:2024
English Version
Paints and varnishes - Coating systems for wind-turbine
rotor blades - Part 6: Determination and evaluation of ice
adhesion using centrifuge (ISO/TS 19392-6:2026)
Peintures et vernis - Matériaux de revêtement pour Beschichtungsstoffe - Beschichtungssysteme für
pales de turbines éoliennes - Partie 6: Détermination et Rotorblätter von Windenergieanlagen - Teil 6:
évaluation de l'adhésion de la glace à l'aide d'une Bestimmung und Bewertung der Eisadhäsion mittels
centrifugeuse (ISO/TS 19392-6:2026) Zentrifuge (ISO/TS 19392-6:2026)
This Technical Specification (CEN/TS) was approved by CEN on 23 February 2026 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 19392-6:2026 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (CEN ISO/TS 19392-6:2026) has been prepared by Technical Committee ISO/TC 35
"Paints and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes”
the secretariat of which is held by DIN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TS 19392-6:2024.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO/TS 19392-6:2026 has been approved by CEN as CEN ISO/TS 19392-6:2026 without any
modification.
Technical
Specification
ISO/TS 19392-6
Second edition
Paints and varnishes — Coating
2026-02
systems for wind-turbine rotor
blades —
Part 6:
Determination and evaluation of ice
adhesion using centrifuge
Peintures et vernis — Matériaux de revêtement pour pales de
turbines éoliennes —
Partie 6: Détermination et évaluation de l'adhésion de la glace à
l'aide d'une centrifugeuse
Reference number
ISO/TS 19392-6:2026(en) © ISO 2026

ISO/TS 19392-6:2026(en)
© ISO 2026
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO/TS 19392-6:2026(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Sampling . 2
7 Test panels . 3
7.1 Substrate .3
7.2 Preparation .3
7.3 Conditioning.3
7.4 Coating thickness .3
7.5 Roughness of coating .4
8 Procedure . 4
8.1 Number of determinations .4
8.2 Examination before exposure . .4
8.3 Sample preparation (ice formation) .4
8.4 Ice adhesion testing .5
8.5 Examination after testing .5
9 Evaluation . 5
10 Precision . 6
11 Test report . 6
Annex A (informative) Example of parameters for ice formation processes . 8
Bibliography . 9

iii
ISO/TS 19392-6:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139, Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO/TS 19392-6:2023), which has been technically
revised.
The main changes are as follows:
— in Clause 1 a note has been added to give more information on the different methods for the determination
of ice adhesion;
— ISO 2808 has been added as a normative reference;
— in 8.3, in the seventh paragraph, considerations on the presence of mould were added;
— in 8.4, Table 1, a header and a separate column for the units were inserted;
— in Clause 9, Formula (1), ω was corrected to the angular momentum ω and the explanation of symbols
was updated;
— in Annex A an introductory sentence was added;
— in Table A.1 a separate column for the units was inserted.
A list of all parts in the ISO 19392 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
---------------------- Page
...